Question about 2004 Honda CBR 1000 RR Fireblade

1 Answer

How much oil to put in the motor for a oil change

Posted by on

  • george_carau Mar 10, 2009

    great thanks

  • myearwood0 May 11, 2010

    what car /size engine?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 948 Answers

3.5 - 4, depending on if you change the filter or not. I would refill with three quarts, check the oil, then add 1/2 quart at a time until it is full.

Posted on Mar 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After changing the motor oil on my 2005 Denali when started oil came out a breather tube down by the transfer case


check the quantity of oil you put in the sump
if there was no indication before the oil change then it suggests that the sump is over full or the oil you drained out was not engine oil

Jul 20, 2015 | Motorcycles

1 Answer

How to change oil 1978 goldwing gl1000


Get 4 quarts of JASO MA certified motor oil. I recommend synthetic , it will shift better when hot. Amsoil is a good choice. Place an oil pan under the front of the motor. Use a 6 point socket to loosen the bolt on the round finned oil filter cover on the front right corner of the motor and spin it off.Take the oil filter out of the cover and make sure you save the washer that will stick to the rubber seal. Pull bolt out of cover and replace o-ring. put bolt back thru cover, first slide on spring,then washer,and then filter and spin back onto motor pressing filter against engine case. Snug bolt but do not over tighten. Now remove bolt in the middle of the front/bottom of motor(large one in middle , NOT small one under water pump). Check aluminum washer,if bad replace.After oil has drained put bolt back in , do not over tighten.Take off fill plug on right rear corner of motor(by final drive shaft) Using a funnel pour in 4 quarts oil (3.9 is correct amount, 1/10th quart does not seem to bother anything). Put plug back in , start up, and check for leaks.

Jun 02, 2010 | 1978 Honda GL 1000 (K3)

1 Answer

2005 Vegas Ness oil change. I bought the bike used so I don't have a repair manual or owners manual. I just want to change my oil but would like some guidance. Thanks!


Look under the motor and you will see the drain plug. I think it takes a 6mm allen. drain the oil and remove your filter, just like on your car. Your bike should take 5 qrts. make sure you put oil on the new oil filters rubber seal and get it hand tight. after you have replaced the oil plug and filter , pull the dip stick over on the right side and look for the full mark and put the oil in. Put the oil stick
all the way back into the motor, and pull it and check it. Check for leaks and ride safe.

May 29, 2010 | 2005 Victory Vegas

1 Answer

Oil how much oil do i need to put in when i change it and what other thing do i need to change and if u could tell me what kind of oil is recomended for thet bike thank you 


Clean or replace the oil filter screen shown below. Use 10w40 motor oil. NEVER use synthetics or oils with "Special" additives. Technically, the oil quantity is .95 US quarts. Just put in the whole quart can and you will be fine. Please rate my answer. Thanks
e1d234a.gif

Jan 10, 2010 | 2002 Honda XR 200

1 Answer

How to change my oil on a kawasaki ninja 750


Get the bike so it is setting upright.
There a plug on the under side of the motor. Remove the plug and have a catch pan to catch the old oil. The filter will need to be changed also. Do this before you put new oil in. Put the plug back in and open the fill plug on the side of the engine and fill with new motorcycle oil. DO NOT USE OIL FOR CARS!! Watch that you do not over fill it.

Sep 28, 2009 | 1995 kawasaki ZXR 750

1 Answer

I just need to no how much oil i put in my bike


1.06 quarts on standard oil change, 1.16 quarts if filter is changed. Use 10w40 motor oil in the gear box. Don't use any synthetic oils, oil marked "EC", or oil with "special" additives. Stick with the major brands; Pennzoil, Quaker State, Mobil or Shell.

Jun 07, 2009 | 2004 Yamaha YZ 250 F

2 Answers

Gearbox oil change


There should be a drain plug either on the bottom of the gearbox or on the side of the gearbox at the bottom. Put in fresh 10w40 motor oil. There will be an oil fill screw either on the left or right side of the gearbox case.

Apr 28, 2009 | 2005 Hyosung GT 250

4 Answers

Were do you drain the oil on a 1340 evo motor


Evo's drain from the oil tank, not the engine

Apr 20, 2009 | 1996 Daelim VS 125

3 Answers

Oil to use


motor oil and trans lube are 2 different oils

Apr 17, 2009 | Buell X1 lightning Motorcycles

1 Answer

Changeing oil


on the right hand side of the motor is the cover for the oil filter. close to your brake pedal, after draining oil from the drain plug located under the motor, remove this cover take out and replace oil filter, put cover back on, be careful not to over tighten bolts, the strip easily. replace drain plug and fill with oil.... hey presto it's done. about 15 mins.....
http://www.stadiumyamaha.com/pages/parts/viewbybrand/parts.aspx

Mar 01, 2009 | 2001 Yamaha V Star 1100 Classic

Not finding what you are looking for?
2004 Honda CBR 1000 RR Fireblade Logo

Related Topics:

224 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4477 Answers

yadayada
yadayada

Level 3 Expert

60960 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...