Question about 2000 Yamaha DT 125 R

1 Answer

My dt125 was running perfect then it started to die out on the rev now it wont start at all any idias

Posted by on

  • watsy57 Mar 10, 2009

    tryed that got it going today but its doing the same rev it up an it will try to die any ideas thanks for geting bac its a 2000

  • watsy57 Mar 15, 2009

    thanks got it going to much oil put in it thanks any way

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

I know this sounds stupid but change spark plug and check lines for choke the line might be pinched and closing the hole and it might have flooded how old is it?

Posted on Mar 09, 2009

  • Wowjmaster Mar 13, 2009

    another thing you can do is look at the gas line and tank. shut of the gas and make shure theres not a cloged line or the gas tank didnt **** up some stuff out of the bottom of the tank., after you chack all your gas lines try to run it for about 2 min. on choke then go from full choke to med. choke and to no choke, to warm iit up. but it still sounds like your not getting enouph gas or ur air filter might be gunked up. ill check with my friend to see wat else it could be but it sounds like its choking from lack of air or gas.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wont rev 3000 rpm


rpm sensor bad this keeps the car from over tacking.

Feb 26, 2014 | Chrysler Cars & Trucks

1 Answer

Vfr 400 nc30 misfire


hi all got a nc 30 vfr 400.strugle to start it there is spark on all 4.have to hold the start in for like 1-3min then it starts ony if i give it some revs but it doesnt rev past 3000rpm it just dies and doesnt start for like a day then same story again.dont know if it is carbs of what

Feb 26, 2012 | Motorcycles

1 Answer

1982 honda cm250c wont stay running


Sounds like fuel supply problem.Take the carburetor apart and clean it thorough especially the pilot screw (use new o-ring) and the idle jet should be perfect cleaned.Check your rubber insulator where the carburetor plugs on to if it has any cracks and draws extra air in the mixture.

Feb 07, 2012 | Motorcycles

2 Answers

I have a husqvarna 261 chainsaw. it will start half the time....the other half...no chance.i changed the spark plug.and im getting very good spark. took the carb apart and cleaned it. checked the plug when...


Hi, from what you have written I believe you have a faulty cdi unit. Carbys don't generally run perfectly intermittently. To test the cdi theory, close the sparkplug gap to approximately half normal gap. If the saw runs fine you have a faulty cdi, shorting ht lead or stop wire. Regards Phil.

Apr 26, 2011 | Husqvarna Garden

1 Answer

I Have a 1999 blazer that starts but motor dies right away.


Check the fuel delivery, first. It could be fuel pump or an obstruction. The best way is to start the car in park, then run over to the engine compartment and rev up the throttle. Keep idle higher than normal. If it wants to die, rev throttle higher to compensate. If it makes no difference, verify fuel pressure when engine dies. Usually ignition related wont even allow the car to start. Any service engine indication?

Mar 02, 2009 | 1999 Chevrolet Blazer

3 Answers

My dt125 starts but when i put it in gear it cuts out


SOUNDS LIKE IT COULD BE THE SAFETY SWITCH FOR THE KICK STAND ,IF THE SWITCH HAS BEEN DAMAGED IT WILL START UP FINE AND WHEN PUT IN TO GEAR AND CLUTCH IS RELEASED IT WILL DIE.(This is a safety feature)

If that don't fix,Please post back

Please rate this fixya solution

Jan 23, 2009 | 2000 Yamaha DT 125 R

Not finding what you are looking for?
2000 Yamaha DT 125 R Logo

Related Topics:

280 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

mikeuk

Level 2 Expert

61 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1128 Answers

D. E. Hev

Level 3 Expert

1132 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...