Question about 1997 Yamaha YZF 750 R

1 Answer

No power to ignition

Jumepd bike off with jumper cables cable acked out lost all power to ignition 4 fuses under seat not blown bike is 1997 Yamaha YZF750

Posted by on

  • joe May 11, 2010

    bike will not start on its own, but will start with a jump?

  • Anonymous Mar 25, 2014

    Any suggestion on what to check

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 69 Answers

Check the main grounds on the bike, also check the main starter relay.

Posted on Mar 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My thundercat wont start, the power comes on and my alarm works. when i start the ignition i hear a ticking coming from a small black box under ther seat but not even a whisper from the engine


Hi, Anonymous and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Security alarm needs a reset.
10. Starter control circuit, relay, or solenoid faulty.
11. Main fuse or circuit breaker may be blown or faulty.
12. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
13. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
YZF600R Forums View topic cat won start relay just clicks
http://www.r1-forum.com/forums/102-00-01-r1-mechanical-help/39482-bike-wont-start-clicking-sound-under-seat.html
Yamaha YZF600 YZF600R 1994 2007 Service Repair Manual PDF Download Manuals...
OEM parts for Yamaha
Yamaha YZF600RP Owner Manual

Jan 07, 2014 | Yamaha YZF 600 R thunder cat Motorcycles

1 Answer

Yamaha 97 wont start


Hi, Anonymous and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Security alarm needs a reset.
10. Starter control circuit, relay, or solenoid faulty.
11. Main fuse or circuit breaker may be blown or faulty.
12. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
13. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
YZF600R Forums View topic Bike wont start help
What to Do Check When Dirt Bike Won Start
Yamaha YZF600 YZF600R 1994 2007 Service Repair Manual PDF Download Manuals...
OEM parts for Yamaha
Yamaha YZF600RP Owner Manual

Feb 01, 2013 | 1997 Yamaha YZF 600 R thunder cat

1 Answer

1993 yamaha fzr 600,started bike and went down road,bike lost power and still no power,battery has power but no power when i turn key on


Hi, Russell and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Faulty starter button/switch.
6. Faulty jiffy stand or clutch pull in switch/sensor.
7. Security alarm needs a reset.
8. Starter control circuit, relay, or solenoid faulty.
9. Main fuse or circuit breaker may be blown or faulty.
10. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue and valuable "FREE" downloads that you will need please visit the websites below. Good luck and have nice a day.
no power to my ignition when turn the key
FZR Won Start The FZR Forum
https://www.tradebit.com/filedetail.php/269137237-yamaha-fzr600-1989-1999-factory-service-repair-manual
OEM parts for Yamaha
http://www.fzrarchives.com/fzr600/600_manual/1999fzr600r.pdf

Aug 31, 2012 | 1993 Yamaha FZR 600

1 Answer

1997 Yamaha YZF 600 keeps blowing ignition fuse


Hi, Irisgt1 before diagnosing your blown fuse issue check the bottom of your seat if it's metal and comes in close proximity to the positive battery post you need to take the necessary steps to ensure there is no contact (electrical tape, thick rubber insulation, hammer a dent in the seat bottom etc.) also you are going to need a wiring from your service manual a test light, an ohmmeter and plenty of extra fuses. If you turn on your ignition switch and immediately blow a fuse you have a hard/dead short and is usually easy to find. With a test light connected to the hot side of the blown fuse holder start stabbing the wire/s that leads away from the fuse holder and towards the ignition switch, you test light will illuminate validating the short. When the test light fails to illuminate you have passed the short and need to back up until the test light illuminates, then look in the immediate area for the short.
If you driving down the road for 30 minutes or 15 miles and blow a fuse you have soft/flying short and may take some time and patience to find.
If the main fuse/circuit breaker constantly blows/trips while riding you probably have a faulty battery terminal connection. Check battery terminals for damage or corrosion, check battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary. Any other fuses that constantly keep blowing while riding are usually caused by a loose or corroded ground wire in the circuit, which means you have to check, inspect, test each and everyone with and ohm meter set on a low ohm scale 100 ohms or less . Simply touch one lead to the ground source and the other lead to the battery negative terminal, a reading of zero indicates a clean solid ground. Any number reading or infinity indicates a poor ground and needs to be repaired. Poor or weak grounds require excessive additional amperage to complete the circuit which in turn blows the small amperage fuse.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
HELP Ignition fuse keeps blowing
http://www.r6messagenet.com/forums/r6-maintenance-technical/71620-help-keep-blowing-ignition-fuse.html
1997 2007 Yamaha YZF600 Service Repair Factory Manual INSTANT DOWNLOAD... $10 cheap
OEM parts for Yamaha
YAMAHA YZF600R Owner Manual

Apr 16, 2017 | 1997 Yamaha YZF 600 R thunder cat

1 Answer

Yamaha wont start


Hi Denver, and the usual suspects are:
1. Ignition switch not in the "ON" position.
2. Engine run switch in the "OFF" position.
3. Discharged battery, loose, corroded or broken battery cables, especially the "NEGATIVE" cable at both ends (solenoid chatters).
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Security alarm needs a reset.
6. Starter control circuit, relay, or solenoid faulty.
7. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue, please visit the websites below. Good luck and have nice a day.
1997 Yamaha Motorcycle Service Repair Manuals

Dec 20, 2011 | 1997 Yamaha YZF Thunder ace 1000 R

1 Answer

My yamaha yzf 600 1997 thundercat just died. Doesn't want to start no lights on dash come on. When I connect jumper cables from car to bike all lights come on and bike starts but dies as soon as jumper...


Hi, Petrusm_jc7 and the usual suspects are:
1. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Air/fuel mixture screw improperly adjusted.
10. Accelerator pump damaged or not working.
11. Water or dirt in the fuel system, carburetor or filter.
12. Restricted, blocked or kinked fuel line.
13. Fuel tank empty.
14. The gas cap is not venting properly or fuel tank venting system blocked.
15. A failed fuel pump, pressure regulator and or fuel injectors.
16. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
17. Needle and seat stuck closed in the float bowl.
For more information about your issue and valuable "FREE" downloads that you need please click on the links below. Good luck and have a nice day.
YZF600R Forums View topic 97 thundercat dies when given throttle
YZF600R Forums View topic Bike wont start help
Yamaha YZF600 YZF600R 1994 2007 Service Repair Manual PDF Download Manuals...
OEM parts for Yamaha
Yamaha YZF600RP Owner Manual

Nov 13, 2011 | 1997 Yamaha YZF 600 R thunder cat

1 Answer

My bike has no power has a good battery and starter solenoid all fuses are also good


Hi, Jakewelbes and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Tip over sensor needs a reset.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Starter control circuit, relay, or solenoid faulty.
10. Main fuse or circuit breaker may be blown or faulty.
11. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
http://www.r1-forum.com/forums/102-00-01-r1-mechanical-help/228208-bike-not-starting-no-power-w-new-battery.html
why doesn my motorcycle power on
2003 2004 Yamaha YZF R6 Service Manual R6 Moto Data Project
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals

May 13, 2011 | 2004 Yamaha YZF-R6

1 Answer

I have a 2000 yamaha xv1600 roadstar. Went for a ride and made a stop. Everything started and ran great. After the stop I went to crank it up and heard a funny noise near the starter and the nothing. ...


Hi, Pawpaw36507 nice novella and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Tip over sensor needs a reset.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Starter control circuit, relay, or solenoid faulty.
10. Main fuse or circuit breaker may be blown or faulty.
11. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
2000 Yamaha XV1600 Wild Star fuse panel location Google Search
Re Fuse box Road Star Forum Yamaha Road Star
Yamaha XV16AL Service Manual
OEM parts for Yamaha
YAMAHA XV1600A Owner Manual

Mar 07, 2017 | 2000 Yamaha XV 1600 Wild Star

3 Answers

I hooked up jumper cables to what appers to be the fuse box under the hood... now I have a bad electical issue all these things don't work: radio, interior lights, Running lights, power windows, seats, nor...


Hi! I am having the same problem. My brother hooked the jumper cables to the fuse box now all the things that went wrong with your car isn't working in mine! Please help! I have a 2002 GMC envoy. What did you do to your car to make it work again

Dec 21, 2010 | 2003 GMC Envoy

1 Answer

Yamaha v star 1100 will not do anything


r u getin fuel-is the tank valve workin-maybe the float is stuck on carb-test to see if getin spark-ignition system could hav bad wire ie plug or coil connect

Aug 20, 2009 | 2003 Yamaha V Star Classic

Not finding what you are looking for?
1997 Yamaha YZF 750 R Logo

Related Topics:

282 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

278 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

D. E. Hev

Level 3 Expert

1167 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...