Question about 1997 Honda CBR 600 F(3)V

2 Answers

Noisey transmission when riding pull clutch in noise goes away let clutch out noise reappears 1997 honda cbr 600 any thoughts please

Posted by on

  • baddad1969 Apr 04, 2009

    has any one told you wot it may be as mine is doing the same

  • Anonymous Mar 19, 2014

    There is an odd noise In my transmission esp. the clutch Looking forward for your help

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

When you squeeze the clutch you put pressure on several components in the clutch assembly. The clutch throw-out bearing, and the assembly that pushes on throw-out bearing. When you release the clutch that bearing floats as the clutch spins. What you are most likely hearing is the bearing floating. After about 30,000 miles this is fairly normal, and due to the cost, repair is only warranted when the clutch is due for replacement.
I am surprised no one has posted this answer in nearly 18 months.
Good luck.

Posted on Apr 01, 2012

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

Where the noise is coming from?

Head of engine?
Centre of engine?

Do you feel that your bike is riding heavy that is you are forwarding the gears but the load of engine is not lightning.

Please reply me then i will tell you the solution.

Posted on Mar 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1999 Honda CBR 600 f4 and recently it won't start while in gear. Before, I could start it while I gear with the clutch lever pulled. Now it only starts while in neutral. Any ideas?


the neutral light, side stand switch and clutch switch are all wired together.
If the neutral light works.then check the side stand cut out works as normal, finally check the micro switch under the clutch lever, it should make a tiny click when the clutch is activated, also check it with a multi meter, follow the wires back to the plug and check the resistance goes from 0 to 1 with the clutch pulled

Jul 09, 2011 | 1999 Honda CBR 600 F(4)X

1 Answer

Recently there is a lot of scratchy noise coming from an engine of my 2003 V-max when I rev it above 3000 rpm. It goes away when the clutch is pulled. Everything is functioning just fine, except that noise...


If noise goes away when clutch is pulled then it is a loose clutch basket,you need to replace clutch basket and clutch,They make complete replacment kits.Its not a big deal but I would stop riding it till you replace worn parts.Running it the way it is will result in a blown clutch and could do more damage.If you have some mechanical ability you can change this yourself.Good Luck Brian.....

May 29, 2011 | 2000 Yamaha V-Max

1 Answer

94 cbr 600 f2, when rolling down on throttle and reducing speed, i hear chattering noise. once i pull in clutch or throttle up, noise goes away. seem to think its trans syncing or grinding teeth. am i...


No, the syncing only comes into play when you are SHIFTING. What you are likely hearing is a chain hitting something during deceleration. Look into chain thightness. Remember to check the chain at it's tightest spot. That means you need to carefully roll the bike, while feeling the chain, for 10 feet or so. Just find the tightest spot of the chain's normal rotation, and adjust at that spot. )Failure to do this burns out bearings quickly.)

I bet you are just slightly out of adjustment....it is normal. Also, clean your chain and lube it when hot.

May 11, 2011 | 1994 Honda CBR 600 F(2)R

1 Answer

I have an engine knock when the bike idles, this goes away when the clutch is pulled in. It also goes away when the bike ticks over about 900 - 1000 revs?


I have the same thing on my 2002 750 Honda Magna I have 20,000 miles (32,000 kilometers) The motorcycle operates flawlessly except for this noise. What it is, is the wear in the clutch plates allowing them to rattle. When you pull the clutch you have put pressure on these plates and the rattle stops. Also when you increase the revs a little the plates tighten up from centrifugal force. I'm just putting up with it until I have to replace the clutch, after replacement of the worn parts the noise will be gone as well.

Dec 22, 2010 | 1987 Honda CBR 750 Hurricane

1 Answer

Bike wont star and clicking noise from solenoid


Hi
Sounds like you have a discharged battery for some reason
Use jump leads, battery charger or replace it

Ride safe
Bike-Doc
Please mark this as very helpful (if it has been!!) - it helps my ratings

May 10, 2010 | 1997 Honda CBR 600 F(3)V

1 Answer

I have a 98 cbr 600. I was riding and all of the sudden the clutch no longer actuated. When I squeeze it doen't spring back. At first I thought the cable snapped off the grip. But, today I looked at it and...


Since it happened suddenly, the problem is probably in the cable. Look at the end of the cable where it connects to the clutch arm. Pull the lever. Does the arm move? If not, replace the cable. Check also that the spring is not broken. If the arm does move as it should then the shaft the arm connects to may be broken.
b3a3eaf.gif

Nov 17, 2009 | 1998 Honda CBR 600 F(3)W

1 Answer

Hi, I have a 1995 GL1500 and it has a slight light rattle at idle when hot. It has covered 55000 mls, i have checked valve timing and carb balance all seems good. bike runs perfect except for noise, any...


Does the noise stop when in neutral with the clutch handle pulled in? If so it may be normal. I have a 1999 Honda Valkyrie (has the same engine setup as your wing) and it is noisey with the clutch handle released at idle, but the noise goes away when the clutch handle is pulled in.

Another thought.......Have you recently adjusted the valves? If not they may need adjusting.

Hope this helps.

Bob

Nov 12, 2009 | 1995 Honda GL 1500 SE Gold Wing

1 Answer

Noise coming from clutch . goes away when clutch is


this sounds like it could possibly be a noisy thrust bearing in the gearbox itself

Apr 21, 2009 | 2001 Honda CB 600 Hornet F

3 Answers

CBF grinding sound


i got an cbr 600rr and somtimes when u press the clutch in it makes a little clicking kinda noise..its just a noisey down side to honda bikes i guess..or it could be somthing to do with ur clutch cable or somthing..im not to for sure tho and that weezing/rasping sound..i am currently havin the same problem.im not sure if were havin the same issue but when i start off and ride around 0-5000rpms it makes a rasping noise..and iw as told this is the chain tensionor and that they are generally bad on honda bikes...i was told go with a manual one..not sure if these are theproblems ur having but sounds somewhat close..hope this helps

Nov 20, 2008 | 2007 Honda CBF 600 S ABS

Not finding what you are looking for?
1997 Honda CBR 600 F(3)V Logo

Related Topics:

480 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4497 Answers

yadayada
yadayada

Level 3 Expert

63990 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...