Question about 2000 Sachs XTC Racing

1 Answer

Rev counter hi cant get the rev counter to work on the sachs is the rev counter work off a pick up in the crank case as the fly wheel moves passed it

Posted by on

  • scorch1988 May 11, 2010

    there are a few possible causes for this
    1. the cable going in to the back of the rev counter may not be tight .
    2. the spring inside the rev counter may be streched.
    3. the sensor may need replacing in the fly wheel


×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 137 Answers

Ello m8,, i see u have a few testers to try out by scorch there,, all i can anserw 4 yuh to your question,, is electronic rev counters if there is no cable,, work off the coils m8,, u can try a quick tester, by runnin a wire from the live or plus from one of the coils and touching it to the live of the rev counter,, bike must be runnin tho,,try that 2 m8,, cheers

Posted on Feb 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Any one know 4by4 Mitsubishi triton no codes cranks need help urgent


the tachometer ( rev counter) get its impulses from the ignition system or in the case of a diesel from the crankshaft position sensor
if it runs with introduced fuel ( dangerous for a diesel) but then dies, that indicates insufficient fuel pressure to the injectors
could be a diesel pressure pump ( test to 25,000 psi) not producing sufficient pressure to work injectors
problem fuel supply to pump, tank venting, filters , air in system etc

Oct 05, 2016 | Mitsubishi Cars & Trucks

1 Answer

I have a toyota camry 220sei it cranks bt doesnt start. When l push it,it starts. Bt when it starts the rev counter doesnt pass 2 and when it moves doesnt rev more than 2


On the diagnostic plug under the bonnet you can bridge out TE1 and E1 and read the fault code on the cluster if it gives any. Is it a 1993 to 1997 model.

Jun 16, 2016 | Toyota Camry Cars & Trucks

1 Answer

Why does my chain saw lose power and shut off as soon as it gets hot.can't restart until it cools off.


Check coil pic up or the electrical pick up in the pull string housing. Remove that and u will see the fly wheel next to that is the electrical pick up .look at fly wheel make sure magnets are clean surface ,they are in the fly wheel itself.after that remove coil and clean surface that faces fly wheel. Using a match book cover place it between fly wheel and coil ,make sure it moves but not falls out snug ,tighten coil screws and remove match book cover. If it dose it again re place coil look for small engine shop in your area and the can help get u a new one .weak spark means coil,sparkplug

Sep 15, 2014 | Poulan PP4218AV 18" Chain Saw

1 Answer

Rev counter not working


Hi, Anonymous for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix/test or parts inquiry. If necessary transport your vehicle to the dealer or shop and have a professional technician take it for a test drive, if it is in running condition, and give you a written estimate of repairs and answer any specific questions you may have about your issue. For more information about your issue please visit the website below. Good luck and have a nice day. DOWNLOAD 2001 Aprilia Rs 125

Jan 28, 2014 | Aprilia RS 125 Motorcycles

1 Answer

Singer 328 is not stiching


if upper thread correct, check bobbin is wound and inserted correctly. Pulling bobbin thread, the bobbin should turn counter clockwise. make sure thread is under bobbin case tension spring. With cover plate open hold needle thread and turn hand wheel towards you to see if hook picks up needle thread and passes it around bobbin case. if not check hook timing

Jan 05, 2014 | Sewing Machines

1 Answer

Cranks over but has no fire


your car is eqiped with a crank positioning sensor .located on the fly wheel ?not exactly sure on that model cheak the pick up sensor wires make sure to turn TDC and make sure the pick up is attached

Jan 10, 2012 | Cars & Trucks

1 Answer

Golf 2 rev counter stopped working


try he alternator the rev counter should be picked up from the w terminal on the alternator

Nov 27, 2011 | Cars & Trucks

1 Answer

I cannot get the timing marks on Crank and fly wheel alinged


to be honest it not as easy as it sounds to line them both up,,,,you may need to use a locking stud to do this,, and i have seen engines that just wont line up even to half a tooth out,,, but they run just fine anyhow, its all down to just how good the pullys were cut and marked

Feb 16, 2010 | 1994 Volkswagen Jetta

1 Answer

Need original back wheel and sprocket and cant


try of course ebay or poss ebikes in bristol UK

Jul 06, 2009 | Sachs Enduro ZZ Motorcycles

1 Answer

While sewing the bobbin case moves, wheel locks up, needle locks


Im not sure if this will help but thought I would pass it along. My Pfaff 6122 tells me to check bobbin for thread unrolling clockwise before you place it back in the machine. I had mine turned to un roll counter clockwise, this is wrong, the bobbin will fall out when you pull on the thread while you are holding it in your hand. You may just keep putting it in backwards. Hope this works for you. J.R.

Feb 05, 2009 | Brother CS-6000

Not finding what you are looking for?
2000 Sachs XTC Racing Logo

Related Topics:

506 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sachs Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4509 Answers

Are you a Sachs Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...