Question about Harley Davidson FXDL Dyna Low Rider Motorcycles

1 Answer

Can't remove my battery box from 1997 dyna glide

Need to remove battery box so i can repair loose negative cable

Posted by on

  • scoopwiden Feb 24, 2009

    thank you very much Mitchy 123 you are the man problem solved.be safe ,thanx again, scoop

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 216 Answers

Remove the seat , battery neg. at frame, positive at terminal, then feel around the outside of the box - there is a rear lower bolt and an upper bolt - - this will cause the battery tray to swing down when removed

Posted on Feb 24, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove battery from 2009 bmw 328i


Disconnect the cable attached to the negative terminal first, then remove the cable attached to the positive terminal. Undo the battery securing clamp and lift the battery out. Be careful the battery is filled with dilute sulphuric acid and can give off Hydrogen gas so avoid any naked lights. Refit in reverse order, connecting negative cable last. If you remove the battery you will loose the code of the radio.

Jan 05, 2014 | Cars & Trucks

1 Answer

How to replace battery


Open the hood of your car and locate the battery.
Disconnect the cable terminals from the old battery's terminals (negative/black first and then positive/red)
Connect the cables to the new battery securely - positive to positive and then negative to negative. The cable ends should not be able to move at all; any looseness can prevent your car from starting.

Sep 21, 2012 | 2005 Nissan Quest 3.5 S

1 Answer

Remove battery from 2002 dyna


The Dyna battery can be removed by:
1. Remove the seat.
2. Remove negative connection at frame, and positive connection at battery.
3. Remove the lower rear bolt. (left side of battery box at frame upright)
4. Remove the upper rear bolt, and swing down the battery box.
5. Remove the top cover, nad side cover.
6. Lift battery out, and remove negative cable from battery.

Feb 05, 2011 | 2002 Harley Davidson FXDL Dyna Low Rider

1 Answer

How to get to battery to change it


The Dyna battery can be removed by:
1. Remove the seat.
2. Remove negative connection at frame, and positive connection at battery.
3. Remove the lower rear bolt. (left side of battery box at frame upright)
4. Remove hte upper rear bolt, and swing down the battery box.
5. Remove the top cover, nad side cover.
6. Lift battery out, and remove negative cable from battery.

Jan 20, 2011 | Harley Davidson FLHTCUI Electra Glide...

2 Answers

2008 kia optima break lights not working



  • kia optima brake light
  • Open the hood and locate the battery. Remove the cable from the negative terminal (black cable) by turning the retaining nut on the cable clamp counterclockwise with a socket wrench until the clamp is loose enough to slide off the terminal. You must disconnect the battery's negative terminal to avoid a potential electrical shock when working on any electrical component in your KIA.
  • Open the trunk and pull back the carpet near the tail light assembly.
  • Remove the three nuts holding the lamp assembly in place and pull the lamp assembly out.
  • Remove the bulb assembly by rotating the bulb counterclockwise and pulling the bulb straight out of the housing.
  • Install the new bulb. Installation is the reverse of removal.
  • Reconnect the cable to the negative battery terminal.


  • Aug 11, 2010 | 2008 Kia Optima

    1 Answer

    Hyundai 2002 gx350 making popping noise


    u can take negative cable off battery and repair problem ur self but u will probley loose compuer memory

    Jul 03, 2009 | 2002 Hyundai XG350

    1 Answer

    A month ago I bought A used 2000 elantra it used to start fpr the first try In the same time I changed the engine oil and Trying to put a good battery when I finished it did not start.


    Verify (test) the battery is good/charged. Verify good, clean cable connections (positive & negative, correct polarity). Inspect positive and negative cables for loosness (positive cable condition to starter connection - clean/tight) negative cable condition to ground connection clean/tight). Replace/repair/clean/tighten cable(s) as needed. Did you remove/disconnect any components from the engine when you replaced the battery? If so, did you remember to put/reconnect them back?

    Apr 22, 2009 | 2000 Hyundai Elantra

    2 Answers

    Remove battery from 99 yukon


    your gonna need either a 5/16 or 8mm wrench.  loosen the negative battery cable (black cable) off first and move it to the side where it wont touch the battery or anything metal.  then loosen and take off the positive (red) cable off and then just loosen the battery hold down bolt and the battery should left out. just like a top post battery make sure you dont touch anything metal with the wrench while loosing the bolts.

    Feb 24, 2009 | 2008 GMC Yukon

    1 Answer

    2005 battery replacement


    Yes you do need to remove the brace "bar" above the battery. If I am not mistaken, the fuse box also has to be relocated for clearance. One thing you must do before you start is disconnect the negative cable from the battery. The negative cable is the black one. One of the oldest rules when working on any vehicle battery is negative is disconnected first and reconnected last. Since the vehicle is "negative ground" it will make it impossible to short negative to ground. The bolts that hold the bar in place are either 13mm or 15mm. The battery is held in place with a plastic wedge that is held down with a 13mm bolt. The battery cables are 8mm.

    Jan 04, 2009 | 2006 Pontiac Montana SV6

    Not finding what you are looking for?
    Motorcycles Logo

    Related Topics:

    450 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Harley Davidson Experts

    Arnie Burke
    Arnie Burke

    Level 3 Expert

    4536 Answers

    Mike

    Level 3 Expert

    4341 Answers

    yadayada
    yadayada

    Level 3 Expert

    77202 Answers

    Are you a Harley Davidson Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...