Question about 1986 Suzuki GSX-R 750 G

1 Answer

Cleaning the carbs

I'm about to buy one of these and i was told the carbs need cleaned, how do you do that

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 66 Answers

1st-take off fairings & tank,seat, take carbs off. drain fuel, & turn over on bench. take bowls off.disassemble jets & floats in each carb, do not mix components from each carb.soak in carb cleaner until clean, & no obstructions in jets. soak bowls also.squirt through carb. air & fuel circuits w/ spray carb. cleaner.when everything is cleaned, reassemble carbs. check carb. float needles for leaks. if all ok ,install carbs on bike.now using remote fuel supply bottle, hook up to carb set.start bike & warm it up,now synchronize carb. set w/ vacuum guage set.reassemble tank,seat, and fairings. note:this really is not a job for the novice w/o competent supervision, a service manual is recommended before beginning.

Posted on Feb 20, 2009

2 Suggested Answers

Mr BrokRench
  • 1623 Answers

SOURCE: backfires, idles ok but no

The best way is to have them boiled or ultrasonic cleaned...If you can't do that, soak them in solvent overnight and use some spray carb cleaner and compressed air to clean out all the passages. I have found that a small steel guitar string works best, for the jets.
Good luck, i hope this helps.

Posted on Aug 10, 2011

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 850 and the carb has varnished gas that was ran through it i has no power and won't harly stay running what can i do. I was also told that gas could have got in my oil would this cause it?


if old gas has sat in the carbs and fuel tank for sometime, they should all be removed and thoroughly cleaned and serviced. this will require dissassembly to an extent. the tank will need cleaning as well to ensure nothing gets back in the carbs after they are reinstalled. the carbs will needs resetting and syncronizing. install a new fuel filter at this time also. ensure a clean air filter and if you smell gas in the oil, change it before starting.

Oct 26, 2009 | 1979 Suzuki GS 750 E

1 Answer

Will cleaning my Troy-Bilt TB25CS carburetor heal it?


Since the air from the air filter does not go through the carb, the carb cleaner will not either. If you remove the carb and spry all of it that you can get to, you may get the plug. If you were to open the carb and go through it and clean it you would need to get new gaskets and maybe that will do the job. You may be able to adjust the carb. There is a "hi" and "low" setting. Try adjusting the "hi"...Lee

Aug 24, 2009 | Troy Bilt Tb70ss Gas Trimmer

1 Answer

Statesman Tiller


without knowing if its a briggs and straton or tecumseh engine ( I assume Briggs) the carb is where the throttle and gas line connect to. carb will need to be rebuilt most likely and tank will have to be removed to be cleaned. you can email me and I could do it for you I am in wisconsin kerryjonjon at yahoo.com I am the most reasonable in this area. I could do carb and tank if you want.

Jul 11, 2009 | Garden

1 Answer

Fuel pump or automatic choke [ 1994Chevrolet 1500 Pu]


You can clean the throttle body plate with carb cleaner just to verify if guy #1 is right. The second mech. likely is way "off base" pump or filter would cause engine to run fine at idle and engine would "lay down" at the top of each gear. I'd do some testing before running out and buy anything more than a can of carb cleaner...Use it to clean wires inside the mass air flow sensor too...that can give similar problems .(use a Q-tip to clean gently so you don't break anything)

Jul 07, 2009 | 1994 Chevrolet K1500

1 Answer

I need to replace the carbs on my '82 Suzuki GS650L


of course they want you to buy new carbs these can be taken apart and cleaned the floats should be weighed to make sure they havent gone bad carb cleaner does miracles to gummed up carbs.

Jun 27, 2009 | 1982 Suzuki Gs 550 L

1 Answer

Craftsman chainsaw runs wide open all the time


It sounds like the needle valve in the carburetor is stuck open. The carburetor could just need a simple cleaning or you may need a new carb. kit.
If the carb. parts (needle valve, gasket(s), diaphragm, & small screen) are more than 3 to 4 years old, you should go ahead and buy the carb. kit. Otherwise just clean the carb. If you need advice on how best to clean the carb., just let me know.

Jim

Jun 11, 2009 | Garden

1 Answer

Craftsman grass trimmer stalls when warm


The carburetor needs cleaned. Disassemble the carb. and spray with carb. cleaner. Use a Den Tek brush, (used for cleaning between teeth), to clean the small portals. This works great for this job. Make sure the small screen in carb. is free of debris. Reassemble carb. and try starting.If this still doesn't solve your problem, you will need to buy a carb. kit and replace the appropriate parts.

Jim

Jun 01, 2009 | Craftsman 25cc Gas Line Trimmer

1 Answer

Sluggish at high idle


More than likely, your carburetor needs cleaned. I like to use a Den Tek Brush, (used for cleaning teeth), to clean out the small ports in carb. Make sure that the small screen is clean and free of debris. If after you do this, and it still doesn't run properly, then you will need to buy a carb. kit and replace the gaskets, needle valve, and small screen. You may have extra gaskets left over, but that's o.k. because that is the way they come.

Jim

May 23, 2009 | Poulan Garden

1 Answer

No Gas to Primer Bulb


It sounds like the carburetor needs cleaned. Take the carb. apart and clean it with carb. cleaner. Use a Den Tech Brush, (used for cleaning teeth), they are perfect for cleaning the small ports in carb. If that still doesn't work, you may need to buy a carb. kit for your weed eater. If so, replace the gaskets and valve needle, and also make sure to replace the small screen. this should all come in the new carb. kit.

May 21, 2009 | Poulan/Weed Eater #Wt200 711724 24cc Gas...

Not finding what you are looking for?
1986 Suzuki GSX-R 750 G Logo

Related Topics:

3,724 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

67930 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...