Question about 2003 kawasaki KX 125

1 Answer

I need to know how much tansmission oil should go

I need to know how much transmission oil should go i kx 125 2005... nobody gives a straight answer...

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

There will be a number on the crank case by the place where you pour the oil in. It will be im millileters so you will need to convert or measure with mL, usually its about 650mL or so for 125s.

Posted on Feb 20, 2009

  • destroyerbmx Feb 20, 2009

    650mL is roughly 2/3 of a quart.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is tansmission oil coming out of dipstick hole. Allision MT 643 on cummins diesel


check the vent on the transmission, if its plugged up it will spit the fluid out the dipstick

Oct 13, 2015 | Cars & Trucks

1 Answer

How can i tell if the belts need replaced or if transmission is bad it will spin but not aggitate


in order to answer your question i need to know the brand when oil is arround belt the transmission is the problem also it has to make noise when spinning that will prove the transmission is bad. on the other hand on same washers when tansmission goes bad it leaks by the seal, son the motor has a speed sensor that when it gets wet it goes bad an the motor will spin but will not agitate.

Nov 02, 2014 | Washing Machines

1 Answer

Tansmission solenoid


  • It is inside the transmission, attached to the valve body. You have to remove the transmission oil pan and valve body to access.

Mar 16, 2014 | 2004 Chrysler Sebring

1 Answer

Code Po734 means on my BMW 2002 (3 series)?? I


PO734 is Gear 4 Ratio Incorrect, slip detected.

Possible causes:
  • Transmission Oil Level Low
  • Output speed sensor problem
  • Engine speed signal circuit between ECM and TCM: Open/Short circuit.
  • Transmission Mechanical Failure.

Sep 24, 2013 | Cars & Trucks

1 Answer

1998 chevrolet k1500 transmission


Try trans oil change, check oil level first ,

Apr 06, 2013 | 1998 Chevrolet K1500

1 Answer

I have a 92 Kawasaki 250 just got it but the thing is I Dnt know wht kind of oil to use for it


You must be more specific about exactly what model 250 you have. ie; KX, Ninja, KLR???? Also in which area does this oil go as in the KX, it would use a 2cycle oil in the gasoline premix and a transmission oil in the gearbox.

Jan 14, 2013 | Motorcycles

1 Answer

1999 Mazda protege has a oily leak just under the radiator what could it be


If the oil you are referring to is pink or red, then it is your transmission fluid. If this is the oil type then I would check the upper and lower tansmissions lines that are routed into your radiator. The purposem of these lines is to cool the transmission fluid. Please see the attached for additional help:

http://www.ehow.com/how_5073604_remove-transmission-cooler-lines.html

Feb 21, 2011 | 2004 Mazda 6

3 Answers

Where is transmission filter located? Is there a way to change filter without removing transmission?


it is inside the xmission..just drop the bottom plate and you will see the filter...do not have to drop transmission to replace

Jan 23, 2011 | 2000 Mercury Mystique

1 Answer

Won.t shift into grear, how do i replace the tansmission filter?


TO DO A TRANSMISSION FLUID CHANGE YOU NEED HAVE TRANSMISSION FLUID ON HAND YOU NEED TRANSMISSION FILTER AND GASKET.YOU NEED 3/8 WRENCH THE RATCHET TYPE WITH METRIC SOCKETS. YOU NEED JACK TO RAISE VECHICLE SUPPORT VECHICLE ON JACK STANDS.YOU NEED A DRAIN PAN. ONCE YOU GET VECHICLE OFF GROUND.PLACE DRAIN PAN UNDER TRANSMISSION OIL PAN REMOVE OIL PAN DRAIN BOLT.LET FLUID DRAIN OUT IN DRAIN PAN THEN SCREW DRAIN PLUG BACK IN PLACE DONT OVER TIGHTEN.REMOVE OIL PAN AND GASKET. BESURE TO HAVE PAPER TOWEL ON HAND.MAKE SURE TRANSMISSION OIL PAN GASKET SURFACE CLEAN BEFORE INSTALLING NEW PAN GASKET. ONCE TRANSMISSION OIL PAN REMOVED. REMOVE THE OLD TRANSMISSION FILTER INSTALL THE NEW FILTER.THEN WITH NEW GASKET ON OIL PAN IN PLACE.OIL PAN NEED TO BE CLEAN SO THE GASKET ADHESIVE WILL HOLD PAN GASKET IN PLACE WHILE INSTALLING PAN AND GASKET TO TRANSMISSION.INSTALL OIL PAN BOLTS INSTALL THEM CRISS CROSS TORQUE PAN BOLTS TO 7 TO 10 FT LBS. LOOK IN OWNERS MANUAL FOR TRANSMISSION FLUID CAPACITY.BUY 10 QUARTS .TO BE ON SAFE SIDE SO YOU WILL HAVE ENOUGH FLUID ON HAND. IF YOU DONT HAVE NO TRANSMISSION FLUID CAPACITY. ADD 7.5 QUARTS FLUID.WAIT FOR 2 MINUTES.CHECK TRANSMISSION FLUID LEVEL ON DIP STICK. SHOULD BE ON THE FULL MARK.CRANK VECHICLE UP.LET IDLE FEW MINUTES CHECK TRANSMISSION DIP FLUID LEVEL IF DROPPED ADD LITTLE MORE.WHILE ENGINE IDLING GETTING WARM UP. KEEP EYE ON FLUID LEVEL.WHEN FLUID LEVEL STOP DROPPING. APPLY BRAKES HOLD FOOT ON BRAKES SHIFT THROUGH ALL GEARS TWO TIMES. THEN CHECK FLUID LEVEL SHOULD BE ON FULL MARK.CHECK FOR LEAKS WHILE ENGINE RUNNING.

Nov 19, 2010 | 1996 Ford F250 Crew Cab

1 Answer

Transmission stuck in neutral (automatic) won't engage drive or reverse


first i would check the transmission oil, do this by starting the engine and leave it running, select all the gears (park, Reverse, neutral etc) then put it back to neutral, leave engine running then locate the transmission dipstick in the engine bay, remove and wipe the dipstick, replace then pull out again, if the oil is showing between the cold and hot marks then level is ok. I shoing lower or none, top up the oil level with automatic tansmission oil, keep rechecking the oil level as adding oil as to ensure it is not over full. will need to select all gears again before checking oil level again.
If the oil level is correct than quite likley a Transmission failure will require mechanic.

May 02, 2009 | 1988 Nissan Pulsar

Not finding what you are looking for?
2003 kawasaki KX 125 Logo

Related Topics:

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

70387 Answers

chris

Level 2 Expert

232 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...