Question about 2001 Suzuki AN 400 Burgman

Open Question

An 400 burgman 2003 how do i adjust the headlight. the beam is to high

Posted by on

5 Suggested Answers

DickCanFixIt
  • 948 Answers

SOURCE: Headlights don't work on start up

Energy must pass through your switch (hi/low or momentary), then to your headlight, and finally to ground. An interruption anywhere will cause the light to go out. Since both your hi and low beams are not working, I suspect a bad ground connection somewhere. Probably in your switch, but if it is easier to check the headlight socket I would check that too. Use a multi-meter, see if you have power to the switch. If you do, ground the negative lead coming to the switch and see if your headlight comes on. If it does, you know you have a bad ground.

Posted on May 21, 2009

  • 1 Answer

SOURCE: how do I change a headlight on a Suzuki Burgman

you reach under the front of the scooter between the headlight and the fender. find the wire that goes to the connector of the headlight. it is directly behind the headlight. unplug the connector, pull the plug off the headlight. remove the rubber cover/boot off the back of the headlight. this is now the tricky part. there is a clip that needs to be unhooked and moved out of the way. remember how you unhook it because you will have to rehook it when you install the new bulb. this hook is a stiff wire with a loop on one end. push on the loop and move it to one side and it will come off the back of the bulb. the clip is attached and will not come off. you should use gloves to remove the bulb. the oils on your hands are not good for the bulb. use glove on removing just in case the bulb is good and you need to use it again. use gloves to install the new bulb. there is only one way to install the new bulb. there are tabs the extend out from the base of the bulb. you can kneel in front and reach your hand under to install the new bulb while you watch the insertion through the glass. rotate the bulb until you feel the detent that allows the bulb to fit into position. both bulbs have the tabs in the same location, ie. the detent tab is about at the 8 oclock position. replace the clip (insure that it clips on to hold the base), the boot and the connector.

Posted on Jun 28, 2009

SOURCE: Burgman 400 - disassemble the driver's backrest

Place the butrest as much backwards as you can, i.e. as if for long legs riders.. if there is a bit of slack push it just a touch forwards until it clicks.. tiny bit. Now look for two tiny screws, philip ones, on each side of the little under seat light, its hard to see them you may have to disengage the damper.. which is probably on a springclip and tiny washer (dont drop it or loose it) the little screws are actually screwed into the metal of the extending poles so be carefull use the right size screwdriver..once you removed it the butrest should slide out.. they are tiny screws.. you can leave them out so you can clean your saddle all over.. its easier to remove it that way.

Posted on Jan 28, 2010

SOURCE: locatio fuse box burgman an 400

For the K8

The fuse box is under the cover just below the instrument panel on the left hand side. So you need to yank that off first its retained by 4 clip n fit rubber buttons. do side by side.

Posted on Jan 28, 2010

SOURCE: need to replace head lamp on suzuki burgman 400

patience is required. you do not need to take any tupperwear off unless you have particularly large hands.
anyway. turn the wheel the opposite direction of the side lamp you wish to replace.
reach carefully up into the lamp area and you will feel the wireing for the lamp,,,,pull it out . then there is a rubber booty around the light bulb connector...take it off.
now comes the tricky part....the bulb is held in with a small wire clamp. if you look inside the head light lense you will see the part that is holding the lamp. with your fingers , pull it down and it will swing out of the way..be carefull not to take it off as it is held in place. you will notice the bulb then will be free, so take it out carefully....
when replacing your bulb, do not touch the lense and slip it back into place. look at the other bulb to see it fits correctly.
the next tricky part is to get the clamp back on by pressing it down and around the lip of the light bulb into place.
replace the rubber booty...then connect the wires...

Posted on Jan 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2003 kia spectra. Can the headlights be adjusted. On low and high beams they seem to be set to low. I feel they should shine out futher to be able to see more while driving at night


the headlights can be adjusted but you can't adjust the high & low beam separately, you can only adjust the light as a unit unless you have a separate high & low beam lights ( twin lights) ......hope this helps......cheers.

Sep 05, 2011 | 2003 Kia Spectra

2 Answers

Just bought an "04 Burgman 400. Idles rough and


i would say that the carb settings are wrong sounds like the tick over screw is to far in do you know how to adjust this?

if not give me a shout and i will find a manual and tell you

John

Feb 02, 2011 | 2003 Suzuki AN 400 Burgman

1 Answer

In adjusting the headlights on a 2003 Olds Alero, it appears there is only one set of adjusters for both the high and low beam. When the low beams are good, the high beams are too high, when the high beams...


Unless a car has been in an accident it is very rare that the adjustment of haedlights change. the usual problem as in your case sounds as if the headlamp is not installed properly. It is either loose or not seated properly. So check there first.

Dec 31, 2009 | 2003 Oldsmobile Alero

1 Answer

Drivers side headlight assy change, Nissan Sentra 2003, Front lens was cracked and old one became opaque instead of mirrorlike(fogged up).Is it hard to change?


Just unscrew the screws holding down the black tabs on top of the headlights and you have to gently pull the headlight out , be careful because the bottom of the headlight has a tab holding it in place (be patient might have to move it around to release the bottom tab). And do the opposite when putting the new headlights on. Even if the bottom tab breaks. the tabs on the top will old the headlight in place. Once it's changed, you'll need to re-aim the headlights...

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 20, 2009 | 2003 Nissan Sentra

2 Answers

Adjust headlites on a 2003 outlander


There is a screw adjuster on the back side of each headlight, near the outer edge.
Here is a picture of its location, from front and rear:

e7694bd.jpg

Oct 17, 2009 | 2003 Mitsubishi Outlander

2 Answers

How to adjust headlight alignment on Audi A6 2003


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 07, 2009 | 2003 Audi A6

2 Answers

Headlights, regular and high beam, are not adjusted properly. Also the high beam sends light straight up in front of the SUV ?


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Sep 25, 2009 | 2003 GMC Envoy

1 Answer

Adjusting the low beam headlight on a 2003 Hyundai Elantra


thats it my freind one on each side/Plaes rate my response thank you very much

Jan 30, 2009 | Hyundai Motor 2003 Elantra

1 Answer

Adjusting the low beam headlight on a 2003 Hyundai Elantra Adjusting the High beam headlight on a 2003 Hyundai Elantra


its all the same the headlight is a complete unit you adjust both/ look for screws behind the headlight one each side one is for horizontal annd the other is for vertical Please rate my response thank you very much

Jan 30, 2009 | Hyundai Motor 2003 Elantra

Not finding what you are looking for?
2001 Suzuki AN 400 Burgman Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

71525 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...