Question about 1981 Suzuki GSX 400 F

Open Question

Valve timing marks for suzuki gsx400s katana - 1981 Suzuki GSX 400 F

Posted by on

2 Suggested Answers

ckoira57
  • 267 Answers

SOURCE: where are the valve timing marks for suzuki gn 250

There is an engraved line on inner band of the camshaft sprocket. This should line up horizontally with upper edge of camshaft cup on the HEAD. Ensure crank is at top dead centre by aligning "T" with centre of magneto cover inspection hole. (the 17mm bolt) Pull chain up tight and feed on from front of sprocket, then screw in tensioner bolts to torque. Cheers.

Posted on Apr 29, 2010

Woods Goat
  • 85 Answers

SOURCE: valve clearance 1990 suzuki 600 katana

Intake and exhaust: .004-.006


*Help me out. Rate me!

Posted on Jun 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to adjust carberator floats


  1. Suzuki GSX750F Katana - Motorcycle Specs

    www.motorcyclespecs.co.za/model/suzu/suzuki_gsx750f_05.htm Suzuki GSX 750F Katana. Year. 2004-05. Engine. Four stroke, transverse four cylinder, DOHC, 4 valves per cylinder. Capacity. 748 cc / 45.6 cu.in. Bore x Stroke ...

Apr 28, 2015 | 1996 Suzuki GSX 750 F (Katana)

2 Answers

1996 suzuki 750 katana can you buy just the carb bowl gasket and the gas needle valve


Yes you can buy a needle valve assembly which consists of a needle ,o ring,and needle seat.in the UK they are about £40 each !

Apr 12, 2015 | 1996 Suzuki GSX 750 F (Katana)

2 Answers

. my 99 suzuki katana


replace the fuel
clean the carbs
change the oil
new plugs
clean air filter
check the valve clearances( if any are really wide a valve may be stuck open)
I assume you have already fitted a new battery

May 21, 2011 | 1999 Suzuki GSX 600 F (Katana)

1 Answer

WHERE IS THE TIMING MARKS ON A GSX 600 KATANA


1-on right side of motor remove the cover,the one with suzuki on it,that is the signal generator cover.2-use 17 mm wrench on signal generator rotor and rotate engine clockwise the "T" mark on the rotor should line up center of the pick up coil,to the left.3-there is a notch on the intake camshaft and a notch on the exhuast camshaft they should point away from the motor level with gasket service.timeing mark on rotor is "T" and timeing marks are the notches on the end of camshafts.

Feb 26, 2011 | 1996 Suzuki GSX 600 F (Katana)

1 Answer

What is the capacity of a 93 suzuki katana 600


Displacement: 599.00 ccm (36.55 cubic inches)
Engine type: In-line four, four-stroke
Power: 86.00 HP (62.8 kW)) @ 11000 RPM
Torque: 58.00 Nm (5.9 kgf-m or 42.8 ft.lbs) @ 9500 RPM
Valves per cylinder: 4

Jul 04, 2010 | 1993 Suzuki GSX 600 F (Katana)

1 Answer

Valve clearance 1990 suzuki 600 katana


Intake and exhaust: .004-.006


*Help me out. Rate me!

May 30, 2010 | 1991 Suzuki GSX 600 F (Katana)

1 Answer

How much oil does a 1996 gsx suzuki katana take for an oil change


it takes about 4.2 quarts, top it off so the oil is just at the center mark of the oil level site glass in the clutch cover

May 24, 2010 | 1996 Suzuki GSX 600 F (Katana)

2 Answers

Do u know the firing order for a 89 suzuki


89 Katana uses two coils, one fires cylinders 1 and 4 together and the other fires 2 and 3 together. It's a waste spark system. So your firing order is either one coil or the other every revolution.

May 02, 2010 | 1989 Suzuki GSX 750 F (Katana)

Not finding what you are looking for?
1981 Suzuki GSX 400 F Logo

Related Topics:

466 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4477 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...