Question about 2005 Honda CRF 250 R

3 Answers

Oil Change to Honda CRF250r 2004

I have drained out old oil, on Right hand side of motor is filler cap, which shows to fill with 770ml of oil. which i have done.

On the left hand side, is the dip stick, do i fill this with any oil.

Posted by on

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 67 Answers

The left side is the ENGINE oil fill. The right side oil fill plug is THE TRANSMISSION oil. There are 2 separate drain plugs also. Honda sells an engine oil with moly HP4M that you should not put in the trans because it will cause clutch slippage. The best performance and protection for your bike is full synthetic engine oil with a dedicated gear oil in the transmission. Get yourself a manual so you will not be as confused

Posted on Feb 18, 2010

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

The engine has two seperate sides which require oil... your owners manual should break it down step by step, if you dont have one id advise strongly to get one, but if not the right side has a 8mm bolt, remove it with the bike in a perfectly vertical position... if oil comes out its full... along with the dipstick on the left side, its pretty self explanitory on how much, just dont put too much in or you could blow seals and you will lose a slight amount of power... both sides use the same oil so you dont have to worry about clutch oil and all that ****... just use motorcycle 10w 30 or whatever... strogly advise hondas line of oil specially tuned for honda engines. keep up on it and that engine will last longer than you expect. have fun and be safe.

Posted on Apr 14, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 119 Answers

This Engine Shares The Oil In The Crankcase With The Transmission . Put Oil In AT Fill Cap , Check Level At Dip Stick. Also This Engine Has An Oil Filter. Don't Forget To Change It . It Should Be Under A Cover That Has 3 8MM Bolts. Use New O-Ring Here.

Posted on Apr 14, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change oil in a Honda Reflex Scooter


Things You'll Need
  • Socket wrench
  • 17 mm socket
  • Drain pan
Instructions
    • 1 Move the Reflex to a level, well-ventilated work area and lift it onto its center stand. Start the Reflex's engine. Let it idle in place for 3 minutes, then stop the engine and let it cool for 10 minutes.
  • 2 Unscrew the oil filler cap from the right engine cover, which is located near the rear swingarm below the right passenger foot peg, by hand.
  • 3 Unscrew the oil screen cap, located directly below the oil cap, using a socket wrench and a 17 mm socket. Drain the engine oil into a drain pan for a minimum of 5 minutes.
  • 4 Pull the oil strainer screen out of the oil screen port by hand. Spray the inner face of the strainer screen, facing the engine, with a parts cleaning spray to remove sediment or particles trapped in the strainer. Push the strainer screen into the engine.
  • 5 Replace the oil screen cap O-ring with a new O-ring. Screw the oil screen cap into the engine by hand. Tighten the cap to 14 foot-pounds, using a torque wrench and a 17 mm socket.
  • 6 Fill the engine with 1 quart of 10W-30 API SG motorcycle-grade engine oil, using a funnel. Screw the oil cap into place by hand.
  • 7 Start the Reflex's engine. Let it idle for 3 minutes, then stop the engine. Check the oil level, using the dipstick built into the oil cap. Add 2 oz. of 10W-30 API SG motorcycle-grade engine oil into the engine, if the oil level is below the dipstick's lower level mark. Do not add oil into the engine, if the oil level is at or near the center of the dipstick's upper and lower marks. Screw the oil cap into place by hand.
  • Jun 27, 2014 | Honda Motorcycles

    1 Answer

    Warning lights on dash of my cbr 929 rry


    Instructions
      • 1 Place a rear stand under the motorcycle's swing arm to support it.
      • 2 Remove the right side fairing panel from the motorcycle, using a 5 mm Allen wrench to unscrew the fairing's bolts. Pull the fairing slightly away from the motorcycle. Reach behind the fairing and unplug the right front turn signal. Set the fairing aside.
      • 3 Shift the motorcycle into neutral and start the motor. Let it warm up for three minutes, then stop the motor.
      • 4 Place an oil pan beneath the drain plug on the bottom of the motor, centered between the exhaust pipes. Unscrew the filler cap from the clutch cover on the right side of the motorcycle.
      • 5 Unscrew the drain plug, using a 17 mm socket and a socket wrench, and drain the motor's oil into the oil pan. Clean the drain plug with a shop towel and reinsert it into the motor. Use a torque wrench to tighten the drain plug to 22 foot-pounds.
      • 6 Use an oil filter cap wrench to unscrew the oil filter from the right side of the motor.
      • 7 Spread an even coat of 10W40 motor oil over the new oil filter's O-ring. Screw the oil filter onto the motor by hand. Use a torque wrench to tighten the oil filter to 20 foot-pounds.
      • 8 Place a funnel into the clutch cover's filler. Pour up to 3.3 quarts of 10W40 motor oil into the motor. Remove the funnel and screw the filler cap into place.
      • 9 Reinstall the right side fairing panel, using a 5 mm Allen wrench to insert the fairing's bolts.
      • 10 Lower the motorcycle from the rear stand and rest it on its kickstand.

    Jan 16, 2013 | 2001 Honda CBR 929 RR Fireblade

    1 Answer

    Where is the oil plug for my 2004 MTD mower. Model no. 12A-998Q795


    Hello, The 2004 MTD Pro walkbehind doesn't have an oil plug per say. I am guessing you wish to perform an oil change. The oil filler cap/tube assembly is also the drain, as is with many walk-behind mowers. ( Here's a link of the engine breakdown showing the parts: http://www.mowerpartsweb.com/MANUALS/HONDA/GCV160A.PDF )

    Make sure the gas has been drained/run dry - this will prevent accidental spills during this proceedure. Next, for safety, disconnect the spark plug wire. At this point, I usually have a couple of blocks handy to place the side wheels ( the ones on the side with the oil dipstick ) On your model it should be the right hand side. just at the edge of the fan cover cowling. between the blocks, have a container ready to catch the oil, I use one of those square margarine tubs as the sides are low - but any suitable container will do. Bear in mind, it should hold about 1/2 to one litre of oil. Be carefull not to tip the machine with the spark plug down - this will cause the air filter to become contaminated and lead to poor starts or not at all. ( If this happens, replace the air filter.) Now jus tip so the spiggot is over the container and allow to drain. Tip back into normal upright position and fill to propper mark. Simple Tip: save any oil containers - they come in handy for the used oil and are easy to take to the hazardous waste disposal.

    Hope it goes smoothly!

    May 11, 2011 | Mtd Garden

    1 Answer

    Why is there 2 oil filler caps and what kind of oil should i put in it


    the right hand side takes transmission fluid witch is light gear box oil and the left side takes engine you can put engine oil in both sides but if your using light gear box oil you can only put that in the right side i say the sides as if i was siting on the bike . and there is seperate sump plugs 1 for each side the 1 on the bottem of the engine is the left side and there is 1 behind the gear change witch is for the right side of the engine should be a big long bolt

    Apr 08, 2010 | 2004 Honda CRF 250 R

    1 Answer

    Where is the oil fill and drain on xjr 1250


    The oil drain nut is on the bottom of the engine between the two middle exhaust pipes. Dont forget to replace the o ring washer when you put it back. The oil filler is the screw cap on the right side top of the engine casing.

    Apr 07, 2010 | 2004 Yamaha XJR 1300

    1 Answer

    How to service cbr 929


    hi budfdy its quite easy to do if you jno what your doing right
    1:run the bike till it reaches working temperature
    2:unscrew the oil plug located underneith engine and drain into a bucket
    3:unscrew the oil filter in the front off the engine near the front wheel
    4:get the new oil filter and dab some oil on the black seal and screw on hand tight
    5:put the sump plug back in and tghten checkiung seal is ok
    6:unscrew filler cap on right side engine casing and fill with oil i reccomend silkolene oils
    7:as you fill with oil the sight glass located below the filler plug will begine to fill with oil stop filling when the oil reaches 1/2-3/4 full on the glass also do this with the bike upright then put the plug back in and start the bike rechecking the oil hasnt dropped
    8:remove seat
    9:unscrew the bolts holding the tank in by the steering and tilt the tank up
    10:unscrew the airbox screw holding the lid in on the out side and lift off replacing with new filter and rebuild back together
    11:check coolant if dirty change but if is clean leave it
    hope this helped buddy

    Sep 12, 2009 | 2001 Honda CBR 929 RR Fireblade

    3 Answers

    Drain the oil and crank oil


    hi buddy if your on about the brake reservoir there totally different lubricants to refill the oil in the engine you need to unscrew the filler plug on the left side casing of the engine the blue plug on pic below and replace the oil with {silkolene pro 4 sx 15w-50} fill this up until it reaches 1/2-3/4 full on the oil sight glasslocated on the right casing also the brake reservoir is on the front brake lever pic below will show you unscrew the lid to refill with dot 4 brake fluid also the same with rear fill with dot 4 hope this helped buddy get back to me if any probz b6ce58c.jpg
    e4bbec4.jpg
    bb499f9.jpg

    Sep 09, 2009 | 2004 Yamaha YZ 250 F

    4 Answers

    How much tranny oil do you put in 2005 CRF250R after oil change?


    You'lll need to put .7 liters of oil on your bike. When you changed the filter, you'll need to add .8 liters of oil.

    Hope this helps! i'd appreciate a rating!
    -levibit-

    Mar 19, 2009 | 2005 Honda CRF 250 R

    3 Answers

    CRF 150 Honda 2007 oil change


    Hi Niven

    There are also 2 separate drains/fillers one for the transmission and the othe for the crankcase . The measure is 620 ml per side, although some guys run up to 700 ml on the transmission. 10W-40 is the correct weight for the engine side. On the trans side a Transmission specific oil in an 80W or 85W grade. Maxima Extra full synthetic is the best oil you can buy for the engine. Maxima MTL is the best for transmissions.

    regards
    robotek

    Nov 16, 2008 | 2004 Honda CRF 150 F

    2 Answers

    How do you change the oil filter on a Hyundai Accent 1998/99?


    Replace the oil filter after draining the old oil, and" BEFORE "adding new fresh oil, otherwise you'll be dump all that fresh oil, on the ground,while you "TRY to get the new filter installed.

    Step 1 Remove drain plug,Drain oil into drain pan
    Step 2 Remove oil filter
    Step 3 Reinstall drain plug,qnce oil has drained.
    Step 4 Fill new filter with oil,lube seal on filter.
    Step 5 Install new filter, Add fresh oil to proper level.replace filler cap
    Step 6 Run engine check for leaks.
    Happy motoring!

    May 23, 2008 | 1999 Hyundai Accent

    Not finding what you are looking for?
    2005 Honda CRF 250 R Logo

    4,624 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Honda Experts

    Arnie Burke
    Arnie Burke

    Level 3 Expert

    4514 Answers

    yadayada
    yadayada

    Level 3 Expert

    68038 Answers

    Gino Cussen
    Gino Cussen

    Level 2 Expert

    216 Answers

    Are you a Honda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...