Question about 2008 Yamaha YZF-R6

1 Answer

How do i disconnect rear license plate light??

Im trying to install my fender eliminator, but do to so i need to remove the stock piece. I cannot finish this because i cannot remove the license plate wire?? help, please...!!

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Remove the seat, Remove the passanger seat there is a black peace of plastic being heald down by a plastic clip

Get that clip off remove your CPU but do not UNPLUG just get the peace of plastic out and you will see the 4 bolts unbolt and disconect all the wires!

Posted on Mar 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove rear fender


To remove the rear fender, you'll have to remove the 4 or 5 bolts that attatch your fender rail to fender, to keep from scratching the paint on the fender when you remove it, loosen one of the fender rails (struts) more than the other side so you can remove fender without scratching it. Becareful with your tail light wiring when your taking the license plate mount/tail light off.

Jan 24, 2015 | 2009 Harley Davidson XL 1200C Sportster...

1 Answer

How do i remove the rear fender on 2012 nightster


Secure the motorcycle upright on a suitable lift and then remove the main fuse and the seat. Lift the motorcycle just sufficiently to remove pressure on the shock absorber bolts and remove the lower ones and then lift the motorcycle higher to increase clearance between the tire and the fender.THEN unplug license plate lamp connector and the right rear lighting harness connector which has a brown band on the harness near the connector and then also unplug left rear harness connector and carefully pull both rear lighting harnesses and the license plate lamp harness through the holes in the fender and free all of the harnesses from the fender harness clips and remove rear turn signal stalk nuts from under the fender on both sides. THEN loosen and remove the front fender support screw and washer and nut and then the rear fender support screw with washer and washer and nut plates if present and remove the screw and washer attaching the rear fender brace. If necessary remove license plate lamp module harness from the upper harness clips on the left side of the inner and separate the license plate bracket from the rear fender brace. THEN remove the rear fender strut covers and the attached turn signal assemblies from the fender struts and pull the turn signal harnesses through the fender holes and struts as the strut covers are taken off. THEN put suitable materials between each fender strut and fender to protect the paint. It might be best to have someone assist and hold the fender at appropriate times. THEN you can remove the seat post with its washer and screw.

Jul 04, 2014 | 2011 Harley Davidson XL 1200N Nightster

1 Answer

How do i remove rear fender on nightster


Secure the motorcycle upright on a suitable lift and then remove the main fuse and the seat. Lift the motorcycle just sufficiently to remove pressure on the shock absorber bolts and remove the lower ones and then lift the motorcycle higher to increase clearance between the tire and the fender.THEN unplug license plate lamp connector and the right rear lighting harness connector which has a brown band on the harness near the connector and then also unplug left rear harness connector and carefully pull both rear lighting harnesses and the license plate lamp harness through the holes in the fender and free all of the harnesses from the fender harness clips and remove rear turn signal stalk nuts from under the fender on both sides. THEN loosen and remove the front fender support screw and washer and nut and then the rear fender support screw with washer and washer and nut plates if present and remove the screw and washer attaching the rear fender brace. If necessary remove license plate lamp module harness from the upper harness clips on the left side of the inner and separate the license plate bracket from the rear fender brace. THEN remove the rear fender strut covers and the attached turn signal assemblies from the fender struts and pull the turn signal harnesses through the fender holes and struts as the strut covers are taken off. THEN put suitable materials between each fender strut and fender to protect the paint. It might be best to have someone assist and hold the fender at appropriate times. THENyou can remove the seat post with its washer and screw.

Jul 04, 2014 | 2011 Harley Davidson XL 1200N Nightster

1 Answer

How to remove rear fender on duece


2003 Softail FXSTD REAR FENDER removal and replacement:

Start by blocking themotorcycle underneath the frame such that the rear wheel is
raised off the ground to allow necessary clearance for removal of the fender and then remove the seat and disconnect the negative battery cable. THEN remove all of the fasteners from both of the fender supports, remove the fasteners and washers from fender underside, remove the fasteners, and spacers adjacent to the oil tank, remove the tail lamp. disconnect and remove the rear turn signal assemblies, disconnect both of the ignition control module connectors and the rear lighting harness, remove the retaining nuts from both fender mounting brackets and lift the fender from the motorcycle. To Disassemble the fender:
start by removing the both screws and washers and remove the license plate bracket from the rear fender. THEN, if needed,remove the tail lamp harness from behind that bracket To Reassemble the fender: start by reinstalling the tail light harness of it was removed and position it along the side with the slot as it was removed from. THEN fasten the license plate bracket and tighten both of the fasteners to 144-180 in-lbs (16.3-20.3 Nm).

To Reinstall the Fender start by positioning the fender inside of the frame tubes and over the tire assembly making sure that both the ECM and the tail light wiring harnesses are not in a position that they might possibly be pinched by the fender and having done that loosely install both fender mounting brackets using on each side, the two nuts that were previously removed from these locations and tighten them all to 20-25 ft-lbs (27.1-33.9 Nm). THEN apply a drop or two of LOCTITE THREADLOCKER 243 (blue) to the fastener threads, install the fasteners and spacers to secure both fender supports and with the spacers on the front fasteners and tighten them to 168-192 in-lbs (19.0-21.7 Nm). THEN re-attach the turn signal assemblies, loosely install the fasteners and washers from the underside of the fender and tighten them to 144-180 in-lbs (16.3-20.3 Nm). THEN re-connect the ignition module connectors and the rear lighting
Harness and install the tail light assembly, reconnect the battery negative cable, properly and securely reinstall the seat.

Jun 16, 2014 | 2003 Harley Davidson FXSTD Softail Deuce

1 Answer

Tag light is not working. is there a fuse that will get the light turned back on?


The fuse labeled REAR PARK LP 15A in the right instrument panel fuse box powers the rear park lamps, and the tag lamps. If your rear park lamps are working then you most likely need to replace the tag lamps (bulbs). Use the following procedure to replace the lamps.

To Remove:
  1. Remove the two mounting screws from the license plate lamp.
  2. Remove the license plate lamp from the rear bumper fascia.
  3. Remove the license plate lamp socket by turning it counterclockwise.
To Install:
  1. Install the license plate lamp socket by turning it clockwise.
  2. Position the license plate lamp to the rear bumper fascia.
  3. Install the license plate lamp mounting screws.

Feb 17, 2011 | 2004 Chevrolet Impala

2 Answers

Back door latch broke cant open back door where can i buy the part and the name of the part


I just bought the part last week for 61.76 from the dealership. It takes about two hours to unscrew the strap from the inside, remove trim from the inside starting at the top, sides and bottom. Remove the license plate from the outside of the hatch. Next remove the 8 bolts (10mm)and 3 white plastic tabs that snap on from the large black plate and move to the side (you don't need to disconnect the wires). From here you can reach around the rear window unit and open the door by moving the latch or pulling the cable. You should remove the 4 nuts that hold on the rear window assembly and move the to reach two nuts which holds the center portion of the trim piece you are trying to remove. There should be a plastic piece covering the cable and latch, it just pops off by pulling it straight out. There are three plastic tabs in the corners and one screw (lock for the hatch) that holds on the license plate assembly to the rear hatch along with two white plastic tabs which are located at the bottom two holes for license plate. These plastic tabs come in from the front. Use pliers to squeeze the together and push. You will need to disconnect the license plate lamp wire connector from the left side. The license plate assembly should drop away. Two screws hold on the latch, remove and replace and reverse proceedure.

Jul 08, 2009 | 2002 Toyota Sequoia

1 Answer

License plate bulbs on 98 Park Avenue


License Plate Lights Removal & Installation 1997 – 2000 To Remove:

License/backup Lamp Assembly


76707d9.gif

  1. Remove the rear compartment lid trim. (if necessary)
  2. Disconnect the license/backup assembly connector from the body harness.
  3. While removing the license/backup lamp assembly from the rear compartment lid, disconnect the harness grommet from the rear compartment lid.
  4. Remove the license lamp housing from the license/backup lamp assembly.
  5. Remove the license lamp bulb from the housing and socket.
To Install:
  1. Install the license lamp bulb into the socket and housing.
  2. Install the license lamp housing onto the license/backup lamp assembly
    • Torque the fastener to 18 in-lb (2 Nm).
  3. While holding the license/backup lamp assembly, install the harness grommet to the rear compartment lid.
  4. Install the license/backup lamp assembly
    • Torque the fasteners to 53 in-lb (6 Nm).
  5. Connect the license/backup assembly connector to the body harness.
  6. Install the rear compartment lid trim. (if necessary)

Jun 30, 2009 | 1998 Buick LeSabre

1 Answer

How do I change the rear license plate light bulbs?


License Plate Lights Removal & Installation License plate lamp retainer clips
a555c7b.gif
To Remove:
Remove or disconnect the following:
  1. License plate
  2. Pin-type retainers and the luggage compartment lid trim panel
  3. License plate lamp electrical connector
  4. Lamp socket from the license plate lamp
  5. Using a suitable tool, through the access hole, release the clips and remove the license plate lamp
To Install:
  1. Install or connect the following:
  2. License plate lamp
  3. Lamp socket to the license plate lamp
  4. Electrical connector
  5. Luggage compartment lid trim panel
  6. License plate

Jun 06, 2009 | 2000 Lincoln LS

1 Answer

Changing rear fender on 2003 fatboy


Here's my 2 cents... you need to remove the seat, saddlebags, disconnect battery, dsconnect the wiring harness, remove the signal lamps and the hardware securing the fender. There are torque values u need to know when installing the new one. This is all in the service manual for your model. I would go to the dealer and get one, you want all the specs correct and thats the only way to get em

Nov 26, 2008 | 2003 Harley Davidson FLSTF Fat boy

1 Answer

Remove the tail


The assembly is bolted on. Depending on how much you want to modify it, there are fender eliminator kits available. Some are just license plate holders. Others are complete rear turn signal and bracket kits. Some have lights for the license plates, some do not. Do a search on the web. If you just don't like how the tail hangs down so low, consider just cutting the it off at the bottom, right below the plate to make it shorter. The reflector isn't necessary to have.

Nov 10, 2008 | 2008 kawasaki Ninja 250R

Not finding what you are looking for?
2008 Yamaha YZF-R6 Logo

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

278 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

D. E. Hev

Level 3 Expert

1167 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...