Question about 2004 Suzuki VS 800 Intruder

1 Answer

Ammount of oil in forks

I changed the fork seals and need to know how much oil to put back??

Posted by on

  • Anonymous Mar 22, 2014

    change fork oil

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 66 Answers

Sae 10 lh/rh14/14 fl. oz.

Posted on Feb 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change the fork seals on 95 electraglide


You take the front wheel out then undo the top and bottom yoke pinch bolts,twist the forks downwards then undo the bolt in the centre at the bottom.then lift the dust seal out with a flat screwdriver and lift out the circuits you may need circling pliers.then pull the top and bottom of the fork apart quickly.it will separate.then change the seals and put it back together you need to install the new seal squarely and do not damage it.refill the oil by undoing the bolt at the top and pouring the fork oil in there.

Feb 22, 2015 | Motorcycles

1 Answer

Volume of fork oil needed per fork for a 1986 VF 400 nc 13


Well, when you take off the fork make sure you empty it first before anything else then make sure that the fork pressure spring is released before changing the seals. The fork oil amount should be no more than 200 cc or no less than 190 cc

Jun 24, 2010 | 1986 Honda VF 400 F

1 Answer

My triple tree bearings nuts are not loose nor are my fork tube clamps. but i still feel like the fron wheel is tracking side to side. do you know what i mean? oh ya checked front axle its tight too.


are the forks leaking oil? is there air pressure in the forks? Start by draining the forks and putting in the correct ammount of the proper oil, and getting the air pressure right then see how she rides. Other things to check, front wheel bearings, worn triple tree bearings.

Mar 12, 2010 | 2000 Yamaha YZF-R6

1 Answer

Front forks will not seal


dissassemble forks and replace fork seals.(and oil) becareful forks are under a lot of spring pressue. use a workbench vise to hold fork tubes. you will need the manual for this. plus you will need to know the "proper" amount of fluid to put back into the forks.

Oct 05, 2009 | 2001 Yamaha WR 426 F

1 Answer

I changed the fork seals but i dont know how much fork oil to put back in fork tubes bike didnt come with a owners manual im having trouble finding repair manual


fork oil type -fork oil#10, oil capacity each leg 388 ml for E-01,28 33 models and 392 ml for the other models standard oil level 142mm for E-01,03,28,33 138mm for the other models

Aug 22, 2009 | 1991 Suzuki VX 800

3 Answers

How do I change the fork seals on a 2008 Honda CRF 250 r? Do I use a special tool? Oil? How much oil? Thanks so much for your expertise. Do I put equal amounts of oil on each side? Inner tube- outer tube?


hi,replacing the seal is quite easy,although it will sound complicated,jack up or lift the bike off the ground so that the front wheel is in the air(about 12-14 inches should be enough,remove the front wheel from the bike,remove each fork leg,this is done by undoing the bolts(4 on each leg)the front fork is quite easy to work on just do one at a time,remove the dust cover from the top of the staunchion tube(larger diameter tube),beneath that dust cover you should see a retaining clip that holds the seal in place,remove the retaining clip(and dont lose it),the seal is now ready to remove,the easiest way that i know to do this is to force a screwdriver through the body of the seal,you may need to hit the screwdriver with a hammer as some seal have a tin backing plate,put a hole through the seal on each side of the fork leg taking care not to damage the chrome of the fork leg,then use the screwdriver to lever the seal out of the fork leg,to reinstall the new seal,put a smear of grease or oil around the outside of the new seal,slide the new seal down the fork leg and seat it squarely into the fork tube,very carefully tap the new seal into place being very carefull not to damage the outer surface,i use a small piece of dowell type timber to do this as the wood doesnt damage the seal surface,i use a small ballpeen hammer to tap the wooden dowell,once you have the seal seated down the tube you should be able to see the groove for the retaining clip,reinstall the retaining clip making sure it is seated corectly,replace the dust cover,if you are going to replce the fork oil or top it up do this once the fork leg is back in the bike,repeat the whole procedure for the other fork leg,once you have done the fork seals reinslall the fork legs back into the bike and refit the front wheel,to top up the oil in each leg,simply undo the large cap on the end of the fork leg,you may have to remove the handlebars to do this,be carefull as the cap will be spring loaded and can easily fly off if you are not ready for it,top up or fill with the correct weight oil for your bike(normally a 10w oil),check with your local honda agent for the correct quantity,normally between 400-500 mls,this all sounds quite complicated but is actually quite easy and can be done with a minimal of tools,each fork shold take about 1/2 hr to do...hope this is a help to you

Jul 15, 2009 | 2005 Honda CRF 250 R

2 Answers

I need to know the fork oil capacity for a Kawasaki GPZ750


the oil is SAE10W20 and you must put 325 ccm if you change the oil, and if you let it all drain over night 380 ccm (plus or minus 4ccm). After that, mesure the level in each cilinder of the fork. In the left one, you must have 120mm (plus or minus 2mm) of air left in the cilinder, and in the right one, 149 mm (plus or minus 2mm) .
Hope this helps. Try getting a repair manual. You will find all the answers there.
Best regards, Gabyshor.

Jun 21, 2009 | 1987 kawasaki GPX 750 R

2 Answers

Have to do fork seals on my honda900rrw how much fork oil and what oil would you recemend


usually, i put about 425cc of fork oil in each fork. you can fit a little more in there to make stiffer or use no less the 370cc for softer.

Jun 14, 2009 | 1998 Honda CBR 900 RR Fireblade

1 Answer

Front fork leaking oil from bottom of the seal.


change the oil seals and oil in the fork,and avoid wheelies on the bike and off road biking 

May 17, 2009 | 2004 Honda CRF 250 R

2 Answers

How to fill the front suspension on a ktm exc 2001


If you get the sevice manual or contact a dealer to get the correct oil amount for your bike, they need to know the model and year, you have to have the forks off the bike. take the fork caps off, take the springs out compress the upper fork tube all the way and add the specified oil. if they also give you the measured amount from the top that's the best way to get both fork oil levels exact. there is a special tool that you set the oil level in millimeters and it sucks out the oil to the right level, but before you do that step after adding the oil always pull and push on the cartage rod several times to remove air from the cartage tube. you will hear the air coming out and you will feel the changes in the cartage rod as the cartage tube fills up with oil and the air is removed.
something i'm confussed on though is if you replaced a seal you would have had to brake down the fork to replace it. you would have poored the oil into a container, cleaned all the internal parts,and used a fork seal driver to install the new seal. part of your question asks where do i put the oil in? thats in the open end of the fork after you have taken off the fork cap. It sounds to me like you only replaced the dust seal on one fork. that is not going to fix your leaking fork. you need to replace the oil seal thats pressed inside of the top fork tube.

Dec 01, 2008 | 2008 KTM 200 EXC

Not finding what you are looking for?
2004 Suzuki VS 800 Intruder Logo

412 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

71694 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...