Question about 2006 kawasaki ZX-14

1 Answer



Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    Uploaded 5 video answers.


    An expert who has answered 20 questions.

  • Expert
  • 150 Answers

Hope this helps
VALVE LASH FOR INTAKE AND EXHAUST - a82ffed2-664e-499e-8a8d-08f0370c71f7.jpg

Posted on Jun 11, 2014

2 Suggested Answers

  • 3 Answers

SOURCE: page 36 is torn out of my 2007 ZX-14 owners

water temp

Posted on Aug 29, 2009

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My 1989 kawasaki zx10 sputters at low rpms. Once it gets to higher rpms, the thing takes off like a bat outta hell. Not nice riding like this in traffic. Any suggestions as to what I need to check?

Hi, Morgan and the usual suspects are:
1. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
2. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Spark plugs in bad condition or partially fouled.
4. Spark plug cables in bad condition and leaking.
5. Spark plug gap too close or too wide.
6. Faulty ignition coil, module, and or sensor.
7. Loose, dirty, or corroded ignition module connector at crankcase.
8. Faulty CKP or CMP, MAP, ETS, ATS, TPS, O2 sensor.
9. Intake air leak.
10. Water, dirt, or rust in the fuel system, carburetor and/or filter.
11. Fuel tank vent system plugged or carburetor vent line closed off.
12. Vacuum line from intake manifold to fuel valve is broken, cracked, pinched, or missing.
13. Carburetor controls misadjusted.
14. Damaged carburetor.
15. Incorrect valve timing.
16. Weak or broken valve springs.
17. Damaged intake or exhaust valve.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
zx10 sputtering on low rpms

Jul 04, 2016 | 1989 kawasaki ZX 10

1 Answer

Intake and exhaust valve clearance for Izusu C240 engine

online says 17mm of the feeler gauge for intake and exhaust valves,but are you asking because your timing belt broke ,because if it did i will check for you to see if this is an interferance engine or not,do you want me to check for you ?

Jan 15, 2013 | 2001 kawasaki ZX-9 R Ninja

1 Answer

I have a 1993 suzuki katana 600, it has high km's. the valves make alot of noise, people say to do re torque the valves, would you know how tight I sould torque them too?

Either your friends are playing with you or they have no idea at all what they are talking about. There is no such thing as a re-torque of the valves. The valves are not screwed or bolted in place. How can you torque a screw or bolt that does not exist? The valve gap , aka valve lash, may need to be reset but no torque on the valves is possible. If resetting the valves, set the gap at .006 intake and .011 exhaust. There will be a lock nut, (not shown in diagram), on each of the adjuster screws. Your bike has two exhaust valves and two intake valves per cylinder. tombones49_184.gif

Jun 20, 2011 | Suzuki GSX 600 F (Katana Motorcycles

1 Answer

What is the valve clearance of XL 125 Honda

Valve lash settings for xl 125 Honda is .002 inch intake and .002 exhaust as well.

Dec 07, 2010 | 1983 Honda XL 125 R

1 Answer

Need valve lash specs

intake 0.10 mm / .004 in

exhaust 0.12 mm / .005 in

May 02, 2010 | 1996 Honda XR 600 R

1 Answer

Need valve lash settings for 82 400 Maxim

Set the intake at .005 and the exhaust at .007

Jun 24, 2009 | 1983 Yamaha XJ 650

1 Answer

Valve adj.

valve clearances for intake & exhaust are the same 0.10-0.15mm (0.004-0.006inch)

Jun 19, 2009 | 1987 Suzuki GSX-R 750 H

1 Answer

Need valve lash for 2003 yamaha ttr 125

valve lash on the intake .003 to .005 inch, .08 to .12 mm,exhaust .004"to.0055 inch,.10 to .14 mm (cold engine).

Apr 07, 2009 | 2003 Yamaha TT-R 125 L

1 Answer

Valve adjustment

Hi brookeside14
Not sure what the Merc marine motors are like, but this style of motorcycle engine  are twin overhead cam with bucket and shim type adjustments valve lash adjustments. Best way to tell you to go about this is to download a full manual from here, it has detailed procedures and everything you need to know to set the valve adjustments. Thanks for using FixYa, a FixYa rating is a great reward for my time to get this info to you. Cheers
regards robotek

Jan 23, 2009 | 2001 kawasaki ZX-12R

1 Answer

Valve clearances

Hi Anne

The cold valve lash for your bike are intake 0.08-0.12mm and exhaust 0.10-0.14mm. You can get this and more specifications for your machine for free here.


Nov 12, 2008 | 2006 Yamaha Ybr 125

Not finding what you are looking for?
2006 kawasaki ZX-14 Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers


Level 3 Expert

67912 Answers


Level 2 Expert

232 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides