Question about 2004 Honda CBR 600 RR

2 Answers

Honda CBR 600RR 04 electrical problem

Engine dies and all 4 indicator light glow when the light is switched to high beam. when switched back to low beam the voltage on the ignition resets itself, indicators go out and the bike will restart..Had the electrics thoroughly checked and problem remains a mystery.This doesn't happen every time high beam is on just periodically.Replaced the battery but problem still remains. Someone suggested this could be a factory fault.

Any suggestions?




Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Does anyone no what problem i have?
I`v got a honda cbr 6 rr 05,tiptop condition starts everytime, runs really well. but when i turn off the engine. " like for filling up or just for 5min" It wont start or reluctant to start first time, but 2hrs later starts perfectly again!
can any one solve this problem please.
thanks. justin

Posted on Mar 24, 2010

  • jack edens Jun 23, 2012

    sounds like it is running over-rich, or if it's an injection, like the injectors are dribbling, flooding the engine, and then two hours later, the fuel has had time to evaporate, and hey presto, no problem

  • jack edens Jun 23, 2012

    sounds like it is running over-rich, or, if it's an injection, like your injectors are dribbling, flooding the engine, and then two hours later it has had time to evaporate. i would definately suggest having a look at the fuel system. hope this helpsya mate

×

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 333 Answers

Sounds like a bad earth and you are getting a + backfeed to you indicators, check all green wires thoroughly on connections and to frame etc.
you can also do a check for me--remove the headlight relay and try again .and come back to me with your results

Posted on Aug 07, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 chev sub head lights wont turn on


Do you know anything about automotive electronics ? Electronic control modules .
Headlamp ON/OFF control is determined by the body control module (BCM) by a signal on the headlamp switch on input circuit when the headlamp switch is in the HEAD position. When the headlamp switch is in the AUTO position, the BCM determines headlamps ON/OFF by the voltage from the ambient light sensor.
If the headlight switch is left in the ON position, the inadvertent power control feature will turn OFF the headlights approximately 10 minutes after the ignition switch is turned to the OFF position. If the driver places the headlight switch in the ON position after the ignition switch has been turned OFF, or if the ignition switch is in the ACCY position, the headlights will remain ON until turned OFF or the battery runs dead.
The high beam indicator is illuminated when the instrument cluster receives a GMLAN serial data message from the BCM that the high beams are illuminated.
High Beams
The high beam headlamps receive voltage from the headlamp high relay located in the underhood fuse block. The BCM controls the relay on the headlamp high beam relay control circuit. High beam control is determined by a signal on the headlamp dimmer switch signal circuit from the multifunction switch. When the headlamp dimmer switch signal circuit is grounded, the BCM grounds the headlamp high beam relay control circuit, illuminating the high beam headlamps. The right and left high beam circuits are independent and are fused independently in the underhood fuse block.
Low Beams - Standard
The low beam headlamps receive voltage from the headlamp low beam relay located in the underhood fuse block. The BCM controls the relay on the headlamp low beam relay control circuit. Low beam control is determined by a signal on the headlamp dimmer switch signal circuit from the multifunction switch. When the headlamp dimmer switch signal circuit is open, the BCM grounds the headlamp low beam relay control circuit, illuminating the low beam headlamps. The right and left low beam circuits are independent are fused independently in the underhood fuse block.

Hooking up a factory scan tool an checking DTC'S - diagnostic trouble codes would be the very first step in trouble shooting this problem .
DTC B257A 00: Headlamp Switch Input Signal Mismatch
DTC 2575 00: Headlamp Control Circuit

Jun 30, 2017 | Cars & Trucks

2 Answers

How do I fix HI beam headlights?


your switch is not good try to double check your switch.

Mar 09, 2015 | Kia Spectra Cars & Trucks

2 Answers

High beam indicator stay on even on low beam


faulty relay under dash somewhere for high beams or faulty switch on steering column. relay should click on and off suspect relay stuck in high beam on most likely location of relay is under bonnet or side panel on vehicle.

Aug 13, 2014 | 1998 Jeep Grand Cherokee

1 Answer

Replace dimmer switch


The headlamps ( high an low ) are controlled by the LCM lamp control module .
Headlamp Dimmer Switch
Under the left side of the IP, on the base of the steering column

Headlights Circuit Description (Buick)
Battery positive voltage (B+) is supplied at all times to the lamp control module (LCM) through the LH underhood fuse block LCM/HDLP circuit breaker via CKT 242 (RED). When the headlamp switch is placed in the ON position, the headlamp switch input to the LCM is grounded via CKT 103 (WHT). The LCM then supplies battery positive voltage (B+) via CKT 12 (TAN) to the following components:
• Left low beam headlamp
• Right low beam headlamp
When the headlamp dimmer switch is placed in the HIGH position, the LCM removes battery positive voltage (B+) from the low beam headlamps. The LCM supplies battery positive voltage (B+) via CKT 11 (LT GRN) to the following components:
• Left high beam headlamp
• Right high beam headlamp
The LCM provides battery positive voltage (B+) to the appropriate headlamps under the following conditions:
• The ignition switch is in the RUN position.
• The ambient light sensor indicates darkness.
The lamp control module (LCM) monitors the ambient light conditions through the ambient light sensor. The ambient light sensor is a variable resistor whose resistance changes as the surrounding ambient light level changes. As the ambient light decreases, the resistance of the ambient light sensor increases. The LCM measures the resistance across the ambient light sensor and determines whether it is day or night.

Search from over 10 Million Auto Parts

Do you know how to test automotive electrical circuits ? Check power in an power out . Videos on youtube on basic automotive electrical testing .

Mar 08, 2017 | Buick LeSabre Cars & Trucks

2 Answers

Daytime running light module location 2001 impala


The daytime running lamps in your 2001 Chevrolet Impala are controlled by the Body Control Module (BCM) Here is a description of how the system works:

The ambient light sensor is a light-sensitive transistor that varies its voltage signal to the Body Control Module (BCM) in response to changes in the outside (ambient) light level. When the BCM receives this signal, the BCM turns ON either the DRL or the headlamp relay for auto headlamp operation. Any function or condition that turns ON the headlamps will cancel the DRL operation.
Thirty seconds after you start the ignition with the headlamp switch set in the OFF position, the DRL will perform one of two actions:

Illuminate the high beam headlights at a reduced intensity in daylight conditions
Illuminate the low beam headlights in low light conditions
The DRL/EXT lamps fuse in the top of the engine fuse block supplies battery positive voltage to both the DRL switch contacts and to the DRL relay coil. When the BCM energizes the DRL relay coil, current flows through the right high beam lamp, to the left hand high beam lamp, to the energized DRL relay switch contacts, to ground G101.
The high beam headlamps are now in series, and split the voltage so that the headlamps illuminate at halt intensity. The DRL operates when the ignition switch is in the RUN position, and the parking brake is not set or the transmission is not in park. When these conditions have been met and the ambient light sensor indicates daytime conditions, the DRL will illuminate.

Oct 10, 2011 | 2001 Chevrolet Impala

2 Answers

Engine stalls(dies-down) upon blinking the headlights...


you have a bad ground,or a battery voltage that is so low,that the 20 amps from the high beams circuit is pulling the voltage down so low that the ignition can not run properly.
put on the rear defogger,does it do it? if not,look for the ground junction common to ignition and the high beam circuits.

Sep 09, 2009 | 1995 Cadillac DeVille

1 Answer

My headlights dont work,.all other lights are fine though,.is it the fuses or the bulbs? im not sure what fuses they would be,.there seem to be different ones for the same thing


do your flash to pass lamps light when you pull the stalk towards you? If yes, the bulbs are ok.
Do the hig beams work?
Your headlamps have sepaerate fuses for each headlamp and you have a low beam relay and a high beam relay under the hood in the black box.
If everything is out, I suspect a bad headlamp switch.
Check car-part.com and look on page with * for cheapest price.

Your owner manual will identify fuses & relays.

PS, You did not recently instal high current bulbs did you? If yes, put originals back in.

HEADLAMPS

The voltage is supplied to the lamp switch through a fuse. This fuse is located in the central junction box in the left-hand footwell.
When the headlamps are switched on, a voltage is supplied to the high beam/low beam switch and to the low beam relay. The relay for the low beam is located in the battery junction box (BJB) in the engine compartment.
If the high beam/low beam switch is set to "low beam", then a voltage is supplied through the low beam relay to the low beam part of the headlamp assembly. The left and right-hand low beams are fused separately. The fuses are located in the battery junction box (BJB) in the engine compartment.
If the high beam/low beam switch is set to "high beam", then a voltage is supplied through the high beam relay to the high beam part of the headlamp assembly. The left and right-hand high beams are fused separately. The fuses are located in the battery junction box (BJB) in the engine compartment.

----------------------------------------------------------------------------------------------------------
Lamp Switch
Removal
  1. s2y~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
    Remove the lower driver's side footwell trim.
  1. Detach the lamp switch bezel.
    • Remove two screws.
  1. Remove the light switch.
    • Remove three screws.
    • Disconnect the electrical connector

Feb 23, 2009 | 2005 Ford Focus

1 Answer

Haed lights


All 4 lights is HIGH beam. The 2 that come on in 'LOW' are the low beams.

Sep 03, 2008 | 1990 Toyota Land Cruiser

Not finding what you are looking for?
2004 Honda CBR 600 RR Logo

1,181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

77499 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...