Question about 2007 Victory Hammer S

Open Question

How to replace headlight bulb on 2007 victory hammer

Lens removal for bulb replacement of bullet headlight?

Posted by on

2 Suggested Answers

  • 200 Answers

SOURCE: victory hammer headlight bulb replacement

Look for phillips screws around the front of the headlight bezel.Remove these and pull the headlight straight forward. Behind the light you now hold in your hand will be a 3 prong electrical connection that you either pull straight back or twist 1/4 turn. You will be replacing the whole headlight like a car or you will have a halogen bulb that twists out of headlight, buy a new one and reverse procedure for reinstall....good luck to you my friend....Tim

Posted on May 11, 2009

  • 63 Answers

SOURCE: 2007 Victory Hammer

G'day, from what I can see from pics, your hammer should be disc brake rear. This means there's usually no need to remove the wheel. If you have a close look at it you should be able to see how the pads are removed. Some pads are held in by pins or bolts that pass through holes in the pad to hold it in, others are held in by the caliper itself & you'll need to remove it to change pads.You'll need to sqeeze the pistons back into the caliper if you're putting new thicker pads in. You can use a G clamp & old pad to do this, just keep an eye on the fluid res.hope this helps :)

Posted on Apr 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pdf manuals


Here is a link to the manual http://www.scribd.com/mobile/doc/75283108

Oct 17, 2013 | 2007 Victory Hammer

1 Answer

Need to replace the headlights in my 1988 ford ranger.


The bulbs are replaceable without removing the headlight lens. Open hood and look behind the headlight lens. You can twist the black round housing holding the bulb socket counter-clockwise and remove bulb with socket. remove bulb thru collar. Install new bulb (DO NOT TOUCH THE GLASS PART WITH YOUR FINGERS). Reconnect.

Feb 02, 2011 | 1988 Ford Ranger

1 Answer

How do you replace the headlight on a 2002 Daewoo Lanos


Hi there, together with providing you the solution to the problem, I also took the liberty of going one step further in giving you steps on how to remove the headlight bulb.

  • Find the hood release handle and activate it, the hood should pop open.
  • Once the hood is popped open locate the hood secondary or safety latch and release it. Then finish opening the hood.
  • Locate and remove mounting clips for any plastic shields that cover the headlight lens mounting screws or clips.
  • Some headlight bulbs can be replaced by simply grasping the bulb socket behind the headlight lens and turn it counter clockwise to remove it. This will expose the headlight bulb.
  • If the headlight bulb socket is not accessible the headlight lens may need to be remove or obstructions behind the bulb removed to gain access to the headlight bulb socket.
  • To remove the headlight lens remove all mounting screws and clips that hold the headlight lens in place.
  • After the headlight housing has been removed from it's mounts, release the headlight bulb from the headlight lens housing (turn counter clockwise) the bulb will then come out of the headlight assembly. Once removed, visually verify that the replacement bulb is exactly the same as the failed bulb before to ensure a proper repair.
  • Clean the headlight lens free from all debris to help maintain the seal from the bulb to the lens. This will keep moisture out of the lens.
  • Install the new headlight bulb by turning the retainer ring or bulb clockwise.
  • Re-install the headlight lens housing and reinstall electrical connector.
  • Re-install plastic covers.
After the job is complete turn the ignition key to the "on" position and activate the headlight switch. Observe the newly replaced headlight bulb to ensure proper operation.

Glad to be of help!!!

Jan 21, 2011 | 2002 Daewoo Lanos

1 Answer

2007 Victory Hammer


G'day, from what I can see from pics, your hammer should be disc brake rear. This means there's usually no need to remove the wheel. If you have a close look at it you should be able to see how the pads are removed. Some pads are held in by pins or bolts that pass through holes in the pad to hold it in, others are held in by the caliper itself & you'll need to remove it to change pads.You'll need to sqeeze the pistons back into the caliper if you're putting new thicker pads in. You can use a G clamp & old pad to do this, just keep an eye on the fluid res.hope this helps :)

Apr 12, 2010 | 2007 Victory Hammer

2 Answers

I don't know how to take off the head light lens cover on my nissan maxiuma


Probably not a lens cover at all. It's just a 1 piece plastic headlight. It you are wanting to replace a bulb , they go in from the back . Open the hood and you should be able to see where the wires to the bulb go in the back of the headlight.

Nov 06, 2009 | 1997 Nissan Maxima

1 Answer

Low beam not working on my 2007 victory hammer, is anyone else having problems with this?


your bulb is probably burned out. Remove the four screws that hold your headlight assembly together and take a look.

Jul 27, 2009 | 2007 Victory Hammer S

2 Answers

Victory hammer headlight bulb replacement


Look for phillips screws around the front of the headlight bezel.Remove these and pull the headlight straight forward. Behind the light you now hold in your hand will be a 3 prong electrical connection that you either pull straight back or twist 1/4 turn. You will be replacing the whole headlight like a car or you will have a halogen bulb that twists out of headlight, buy a new one and reverse procedure for reinstall....good luck to you my friend....Tim

Apr 27, 2009 | 2007 Victory Hammer S

1 Answer

2007 air filter replacement


The headlight assembly is accessed from inside the fender well. There are two pop out plastic rivets and a small (4mm? head) body screw that secure the fender liner to the fender. Those need to be removed. Pull the fender liner back enough to work your arm into the fender. Locate the wiring to the headlight and grasp the plug. Rotate it to the left until the bulb is free of the reflector. Pull the lamp and wiring out from behind the fender liner. Remove the bad bulb. There is a release tab on the plug. Insert the new bulb into the plug. DO NOT touch the bulb glass. The oil from your skin can cause the bulb to explode when it gets hot. Hold the plug and work the bulb and wiring back to the original position. It is a little easier to look through the headlight lens as you work the bulb back into the reflector. Turn the plug to the right until it is properly seated. Replace the two pop out rivets and the body screw.

You should replace the headlights in pairs. I didn't and the right bulb went out in a couple more weeks when the weather was much worse. The right bulb was more of a pain to replace than the left, probably because I am right handed.

Hope this helps.

Feb 03, 2009 | 2007 Chevrolet HHR Special Edition

1 Answer

Driver's side Headlight Bulb Replacement


Do you mean the entire headlight assembly or just the bulb?
If it's the entire headlamp look at the new one to see where the fastening points are, the grill may have to be removed and also the parking lamp lens, if it's just the bulb it's easy Open your hood look at the back of the headlight assembly and twist the bulb holder ring to release it. Good Luck To You

Jan 20, 2009 | 2008 Honda Element

1 Answer

Head light 07 HHR


The headlight assembly is accessed from inside the fender well. There are two pop out plastic rivets and a small (4mm? head) body screw that secure the fender liner to the fender. Those need to be removed. Pull the fender liner back enough to work your arm into the fender. Locate the wiring to the headlight and grasp the plug. Rotate it to the left until the bulb is free of the reflector. Pull the lamp and wiring out from behind the fender liner. Remove the bad bulb. There is a release tab on the plug. Insert the new bulb into the plug. DO NOT touch the bulb glass. The oil from your skin can cause the bulb to explode when it gets hot. Hold the plug and work the bulb and wiring back to the original position. It is a little easier to look through the headlight lens as you work the bulb back into the reflector. Turn the plug to the right until it is properly seated. Replace the two pop out rivets and the body screw.

You should replace the headlights in pairs. I didn't and the right bulb went out in a couple more weeks when the weather was much worse. The right bulb was more of a pain to replace than the left, probably because I am right handed.

Hope this helps.

Nov 24, 2008 | 2007 Chevrolet HHR Special Edition

Not finding what you are looking for?
2007 Victory Hammer S Logo

Related Topics:

462 people viewed this question

Ask a Question

Usually answered in minutes!

Top Victory Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Joseph Hoffmann

Level 3 Expert

1700 Answers

Are you a Victory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...