Question about 1995 kawasaki KLE 500

1 Answer

Adjusting front suspension

How do I adjust front suspension of KLE 500. Do you need special tools or measuring equipment to increase the presure. The suspension is to soft and bike "dives" when I close throttle.
Please help.


Thanks
Etienne

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 29 Answers

Yes you are going to need a technical manual with the gauged settings of the factory. This will set to default factory and you can then adjust to what the setting adjustments are to fit your confort.

Posted on Jan 30, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Kawasaki KLE 500 relay location


Hi, Yoni could be starter, fuel pump, brake light, headlight, or horn, for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
2005 Kawasaki KLE 500 relay location Google Search
How do test the headlight relay Kawasaki Versys Forum
Kawasaki KLE500 Service Manual
OEM Parts for Kawasaki
http://mybikemanuals.com/kawasaki

Dec 17, 2013 | 2005 kawasaki KLE 500

1 Answer

1992 Kawasaki KLE 500 rear shock swap


Hi, Davy parts swapping is common with most motorcycles when it comes to interchangeable or compatible parts from one model with another "EXCEPT" for the CDI's they are year-make-model "SPECIFIC" the best thing to do is call your local Dealership Parts Department or a reputable independent shop. If your location is not near a shop then go online and find a parts catalog or "FICHE" and match part numbers depending on your criteria.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
kle 500 1997 rear shock absorber Horizons Unlimited The HUBB Motorcycle Repair How to adjust the rear suspension preload on 2009...
Kawasaki KLE500 Service Manual
OEM Parts for Kawasaki
http://mybikemanuals.com/kawasaki

Jul 20, 2013 | 1992 kawasaki KLE 500

1 Answer

1994 kawasaki KLE 500 engine oil capacity


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Parts Specifications KAWASAKI KLE 500 Louis Moto
Oil for Kawasaki KLE KLE 500 KLE500 1991 2004 Which oil is the best...
Kawasaki KLE500 Service Manual
OEM Parts for Kawasaki
http://mybikemanuals.com/kawasaki/kawasaki-kl-owners-manuals

Apr 19, 2013 | 1994 kawasaki KLE 500

2 Answers

I want to know how to fix the alignment on my 1995 honda accord ex.


Before making wheel alignment adjustment, perform the following checks:
  1. Tires should be equal in size and runout must not be excessive. Tires and wheels should be in balance, and inflated to manufacturer's specifications.

  2. Wheel bearings must be properly adjusted. Steering linkage and suspension must not have excessive looseness. Check for wear in tie rod ends and ball joints.
  3. Steering gear box must not have excessive play. Check and adjust to manufacturer's specifications.
  4. Vehicle must be at curb height with full fuel load and spare tire in vehicle. No extra load should be on vehicle.
  5. Vehicle must be level with floor and with suspension settled. Jounce front and rear of vehicle several times and allow it to settle to normal curb height.
  6. If steering wheel is not centered with front wheels in straight-ahead position, correct by shortening one tie rod adjusting sleeve and lengthening opposite sleeve equal amounts.
  7. Ensure wheel lug nuts are tightened to torque specifications
Ride Height Adjustment

Before adjusting alignment, check riding height. Riding height must be checked with vehicle on level floor and tires properly inflated. Passenger and luggage compartments must be unloaded. Bounce vehicle several times, and allow suspension to settle. Visually inspect vehicle from front to rear and from side to side for signs of abnormal height.
Measure riding height. See figure. Riding height between left and right sides of vehicle should vary less than 1′ (25.4 mm). If riding height is not within specification, check suspension components and repair or replace them as necessary.
Wheel Alignment Procedures

Honda recommends using commercially available computerized 4-wheel alignment equipment. Follow equipment manufacturer instructions to obtain vehicle alignment settings. Use following procedures for necessary adjustments.
Civic Camber Adjustment
Compare camber settings with vehicle manufacturer recommendations. If camber is incorrect, check for bent or damaged front suspension components. Replace faulty components. Recheck camber.
Civic Caster Adjustment
DO NOT use more than 2 shims. If more than 2 shims are required to adjust caster angle, check for bent or damaged suspension components.
Compare caster settings with vehicle manufacturer recommendations. If caster is incorrect, check for bent or damaged front suspension components. Replace faulty components. Recheck caster.
Civic Toe-In Adjustment

  1. Secure steering wheel in straight-ahead position. Measure front wheel toe-in. If adjustment is needed, loosen tie rod lock nuts. Turn both tie rods equally in the same direction until front wheels are in straight-ahead position and toe-in reading is correct. Tighten tie rod lock nuts. Reposition tie rod boots if twisted.
  2. Ensure parking brake is released. Check rear wheel toe-in. If adjustment is needed, hold adjusting bolt on rear compensator arm and loosen lock nut. See figure. Adjust rear toe-in by sliding rear control arm until rear toe-in is correct. Install NEW lock nut, and tighten it while holding adjusting bolt.
Wheel Alignment Specifications

  • Camber - Measurement in degrees.
    • Front: 0 (range -1 to 1)
    • Rear: 0.33 (range -1.33 to 0.67)
  • Caster - Measurement in degrees.
    • 1.17 (range 0.17 to 2.17)
  • Toe-In - Measurement in inches (mm).
    • Front: -0 (0)
    • Rear: 0.08 (2.0)
  • Toe-In - Measurement in degrees.
    • Front: 0.00 (range - 0.16 to 0.16)
  • Toe-Out On Turns - Measurement in degrees.
    • Inner: 41.00
    • Outer: 33.50
Torque Specifications Ft. Lbs (N.m)

  • Rear Control Arm Adjusting Bolt: 48 (65)
  • Spindle Nut: 136 (185)
  • Tie Rod Lock Nut: 41 (55)
  • Wheel Lug Nuts: 80 (108)
hope this helps you out.

May 09, 2011 | 1995 Honda Accord

1 Answer

Factory suspension settings


Spring preload FR
To increase the spring preload and
thereby harden the suspension, turn
the adjusting bolt on each fork leg in direction
a. To decrease the spring preload
and thereby soften the
suspension, turn the adjusting bolt on
each fork leg in direction b
NOTE: _
Align the appropriate groove on the adjusting
mechanism with the top of the
front fork cap bolt.
_
CI-10E
Rebound damping force
To increase the rebound damping
force and thereby harden the rebound
damping, turn the adjusting screw on
each fork leg in direction a. To decrease
the rebound damping force and
thereby soften the rebound damping,
turn the adjusting screw on each fork
leg in direction b.
CI-02E
Compression damping force
To increase the compression damping
force and thereby harden the compression
damping, turn the adjusting screw
on each fork leg in direction a. To decrease
the compression damping force
and thereby soften the compression
damping, turn the adjusting screw on
each fork leg in direction b.
CI-02E
1. Current setting
2. Front fork cap bolt
Setting
Minimum (soft) 8
Standard 6
Maximum (hard) 1
1. Rebound damping force adjusting screw
Minimum (soft) 26 clicks in direction b*
Standard 13 clicks in direction b*
Maximum (hard) 1 click in direction b*
* With the adjusting screw fully turned in direction a
1. Compression damping force adjusting screw
Minimum (soft) 20 clicks in direction b*
Standard 13 clicks in direction b*
Maximum (hard) 1 click in direction b*
* With the adjusting screw fully turned in direction a
_
Although the total number of clicks of a
damping force adjusting mechanism
may not exactly match the above specifications
due to small differences in
production, the actual number of clicks
always represents the entire adjusting
range. To obtain a precise adjustment,
it would be advisable to check the number
of clicks of each damping force adjusting
mechanism and to modify the
specifications as necessary
CI-10E
Rebound damping force RR
To increase the rebound damping
force and thereby harden the rebound
damping, turn the adjusting screw in direction
a. To decrease the rebound
damping force and thereby soften the
rebound damping, turn the adjusting
screw in direction b.
CI-14E
Compression damping force
To increase the compression damping
force and thereby harden the compression
damping, turn the adjusting screw
in direction a. To decrease the compression
damping force and thereby
soften the compression damping, turn
the adjusting screw in direction b.
CI-14E
Setting
Minimum (soft) 1
Standard 4
Maximum (hard) 9

Whole process where need to turn toward "a" means clockwise and "b" counterclockwise. From Yamaha service manual. Hope this is good enough info to help you out. Good?

May 03, 2010 | 2002 Yamaha YZF-R1

1 Answer

Just need to replace the rear suspension springs. I have a replacement set, but need to know if I can do myself easily- or do I need special tools/equipment.?


u can do it yourself if u have some experience, u will need jack stands and floor jack heavy breaker bar and tape measure. u jack truck up until tires in the air support frame with jack stands and then jack axle loosen blolts and lift axle up/ down til u can pull bolys out put in new spring retighten measure both sides to common point to make sure axle is staright then do other side when done remeasure adjust if needed

Jul 06, 2009 | 2002 Chevrolet Tahoe

1 Answer

Adjusting suspension


hi there,,if u can see a air valve on top of the forks, then u can use a bicycle or foot pump to squeeze a bit more air to the fork,, or if there is an adjuster on the fork,ie, a plastic lookin cap with 1 2 3 4 and a arrow on it u can turn that to a comfortable position,, if there is nothing u can see, then u either have not enuff fork oil in each fork leg,,or if there is enuff,, u will need to change the grade of fork oil and replace wots in it,, so id say a more harder grade of oil,, usually there isnt enuff oil in the forks to make it dive into the front wheel,, try topping the oil up,,with about,4or 5 egg cup fulls of oil in each leg,,if nothing has made any difference,, put in another 4 or 5 ,,,any probs on how u put oil in2 the legs ,please do come back in ,and il tell u how 2,, im assuming u do no,, ok ,,cheers

Jan 29, 2009 | 1995 kawasaki KLE 500

1 Answer

Kawasaki KLE 500 B6F rear shock absorber


hagon shocks will more than likely be the people to contact ww.hagon-shocks.co.uk
a very good British manufacturer
good luck ian

Dec 31, 2008 | 2006 kawasaki KLE 500

1 Answer

The car is darting to the left and right.


Check wheel alignment and suspension system components. You'll need to seek a professional in alignment procedures for this one and the equipment necessary to complete it. Hyundai Service Centers are equipped with all the special tools/equipment to do this. It could simply be negative (-) front toe, or a combination of Camber and Caster measurements (cross Camber) adjustments. Hyundai Parts department stocks (or can order) Camber kits & Service can install them if this is where the problem is.

Dec 06, 2008 | 2004 Hyundai Tiburon

Not finding what you are looking for?
1995 kawasaki KLE 500 Logo

Related Topics:

503 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4818 Answers

yadayada
yadayada

Level 3 Expert

78919 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...