Question about 2001 Yamaha FZS 400 Fazer

1 Answer

Sequence for starter washers

Hello. I recently rebuilt a starter for my 2004 Yamaha Kodiak ATV. After I reinstalled the starter in my Quad, it still would not start. Power goes to the selinoid but the Starter just won't engage. I was told that the washers must be placed back onto the starter (after rebuild) in a certain sequence or the starter won't work. I have tried in vain to locate any info on what the sequence of the starter washers are. Since there are five washers, (some metal and some non-metal) that makes for a lot of combinations.


Sorry about the "products category" below but I could not find ATV

Could you help?

Thanks AL

Posted by on

  • fishnwithchi Jan 30, 2009

    Thanks very much. This is the diagram I have been looking for.



    You guys rock.



    Canadian... AL

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,559 Answers

Here you go,Please rate this fixya

sequence for starter washers - ad1af35.jpg

Posted on Jan 29, 2009

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install choke cable on 400 Kodiak atv ?


Your information is on the ATV Forum

Throttle cable: remove the 3 screws on the right side of the carb, take off the cover, there is small rubber gasket (red) Don't lose it. you'll see the cable attached inside. move the mechanism forward like you're opening the throttle to get enough slack to unhook the cable.

Choke: on the other side of the carb, the choke cable screws in with a plastic nut (10 mm i think) unscrew with your hand, if its tight use pliers or wrench..its easy to unscrew it.

throttle choke cable removal Yamaha Grizzly ATV Forum

Sep 12, 2015 | Yamaha Vehicle Parts & Accessories

1 Answer

Yamaha 400 kodiak


is it belt driven if it is check belt for slippage if not check fluid in the drive axles and gears

Aug 17, 2014 | 1993-1994 Yamaha Yfm400 Kodiak Bear 4x4...

2 Answers

1996 yamaha kodiak 400 ATV starter spins but will not engage the engine, what is the problem?


The starter Bendix gear must be stuck in the disengage position, and is not engaging the flywheel. Try hitting the starter with a rubber mallet or with a piece of wood and a hammer. You may be able to loosen the gear by spraying some WD40 or the like into the gear. You probably should take the starter off to clean /lube the gear. If all fails, you're looking at a new starter.

May 14, 2014 | Yamaha 96 Kodiak 400 Generator Stator...

1 Answer

How to line up timing chain for 2000 Yamaha 400 Kodiak 4 wheeler


not sure what motor is in that, but i am sure you can get the manual from Yamaha. You will need to line up cam and crank on cylinder 1 tdc

Jan 09, 2014 | Atv Cover Quad 4 Wheeler Yamaha Yfz450x...

1 Answer

Where is the neutral saftery switch on 1995 Kodiak - the reverse light remains on and will not disengage


problem might be the two wires that go into reverse bulb on dash are shorting, give them a wiggle while pushing starter button

Nov 27, 2013 | Electrosport 1995 Yamaha Yfm400 Kodiak Atv...

1 Answer

How and what do I need to change front wheel bearing in a 2004 Yamaha kodiak ,(4oo cc)atv


If it's 4x4 look here for diagram
You will need to remove the wheel, then remove the center rubber cap, remove the pin on the castle nut, remove the nut and washer and pull the assembly off.

Jun 28, 2011 | Sport & Outdoor - Others

1 Answer

I have a 2003 yamaha kodiak ATV, reverese indicator light stays


MAKE SURE THAT FORWARD AND REVERSE ARE FULLY ENGAGEING AND DISENGAGING

Jan 18, 2010 | 2003 Yamaha YZ 450 F

Not finding what you are looking for?
2001 Yamaha FZS 400 Fazer Logo

Related Topics:

314 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

mikeuk

Level 2 Expert

61 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1128 Answers

D. E. Hev

Level 3 Expert

1132 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...