Question about 2008 Peugeot Ludix 2 Trend

Open Question

Peugeot ludix rear wheel removal - 2008 Peugeot Ludix 2 Trend

Posted by Anonymous on

2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 3567 Answers

SOURCE: what is the psi for

Look at the sidewall of both tires. There will be a 'MAX PSI' embossed on the tire. It will probably say Max 45 PSI. At 45psi the bike will ride like a rock. At 15psi it will ride really squirrely. Find a psi at which you feel the bike handles well and rides well. One rider may weigh 125 pounds and the next rider may weigh 300 pounds. The best psi for each rider will be different due to weight. Chances are that 30 to 35 psi will do the trick. Please take a moment to rate my answer. Thanks.

Posted on Aug 10, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 2006 peugeot 206 1.6 16v. How do I replace the rear wheel bearings

Hi you will need a hydrolic press for the job. Remove wheel, brakes, and center hub net. Then remove the clip holding in the bearing. Good luck.

May 07, 2015 | Peugeot Cars & Trucks


Peugeot 207 rear wheel brake cyclinder replacement

When replacing a Peugeot 207 rear wheel brake cylinder, the Workshop Manual recommends that once the drum has been removed, the brake pipe disconnected from the cyclinder, and the cylinder retaining bolt removed, the upper brake shoe return spring should be removed to allow the cyclinder to be withdrawn from its mounting position.

It is not neccessary to remove the upper brake shoe return spring (tricky to do and even more difficult to put back) - just raise the handbrake (emergency brake) lever a few clicks until the ends of the brake shoes are clear of the cylinder. The cylinder can then be manoeuvred over the upper return spring.

on Apr 13, 2014 | Cars & Trucks

1 Answer

Peugeot C-Tech - How do I remove the rear wheel?

You answered your own question... you will have to remove the brake caliber and slide it off the rotor. The exhaust shouldn't be in the way but if it is you should remove it as well

Jul 01, 2014 | 2009 Peugeot Jet CTech

3 Answers

Ludix one 50cc keeps cutting out

Take it back to the dealer and have them fix it if it is new.

Jun 28, 2014 | 2007 Peugeot Ludix One Dual Seat

1 Answer

Manual free

not quite sure what you mean but the only electrical wires that could be going to the carb would be for the auto choke which works similar to a thermostat have you got starting issues

Jul 13, 2013 | 2007 Peugeot Ludix Snake

1 Answer

Rear breaks seized on peugeot 206 1.6 2000?

Sounds like the wheel cylinders have siezed up and where the car has been left then tried to move pushing on the brakes has pushed them out but they are too rusty to return in ,only way here is to remove the rear drums with a special puller which will destroy the shoes and the anchor pins that hold the shoes on . A rear shoe kit complete with new cylinders is not expensive for this car and costs about 70 euros

Jan 30, 2013 | Peugeot 206 Cars & Trucks

2 Answers

How to change alternator on peugeot 1.4 16v

For step by step alternator removal on Peugeot vehicle,click the link below:----

How to change Alternator on Peugeot


These will help.


Nov 28, 2012 | Cars & Trucks

2 Answers

What is the psi for a peugeot ludix trend tyre?

35-55 I would guess, look on the sidewall to be sure.

Aug 10, 2011 | Peugeot Furia Max 50 Supermotard...

1 Answer

PEUGEOT LUDIX BLASTER RS12 will not start, would the carburettor starter stop it starting if it is not working and is there anyway to test it ? the plug is sparking and the petrol is getting to the carb...

If you're getting fuel and spark, it should start assuming you also have compression. Try putting in a fresh plug; sometimes a plug will appear to have spark when you test it and wont spark under pressure.

Jun 28, 2011 | 2007 Peugeot Blaster RS12

Not finding what you are looking for?
2008 Peugeot Ludix 2 Trend Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Joseph Hoffmann

Level 3 Expert

1702 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

adam bikedoc

Level 3 Expert

661 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides