Question about Motorcycles

1 Answer

Looking for mixture adjustment screw on 93 TR magna efi 2.6

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 427 Answers

Being an EFI system it will most likely not have a mixture adjustment. The mixture is normally controlled by the ecm just like on a car.

Posted on Jan 22, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Thunder55
  • 318 Answers

SOURCE: fuel mixture screw

Begin by screwing the mixture screw in all the way until it stopps,,,but ONLY JUST STOPS,,,,,DONT FORCE IT,,,then look at the top of the screw slot,,and call that 12 oclock,,,now turn the screw out to you three full turns going through 12oclock,,that means 12 to 12 is one turn.

then start the bike,,,finish your adjustments now by slowley turning the screw outwards until the engine starts to misfire,,,at this point turn the screw back in one half to three quarters of a turn.Now you have the mixture set roughly.
For fine tuning,, you need to use a monometer while turning the mixture screw
Best of luck...

Posted on Jan 19, 2009

  • 1 Answer

SOURCE: looking for the air fuel mixture screws on carb any help?

[IMG]http://i199.photobucket.com/albums/aa59/88gixxer/100_4177.jpg[/IMG]

Posted on Apr 09, 2009

  • 65 Answers

SOURCE: flooding problem need to adjust mixture screw to correct setting

is air filter clean and what is your elevation?

Posted on May 05, 2009

dmsr63
  • 2050 Answers

SOURCE: Mixture screw on Carb

I believe it is near the bottom, around where the float bowl meets the carb body.. You need a straight small screwdriver (Short) facing upward.

Posted on Jul 29, 2009

  • 2 Answers

SOURCE: 1997 Honda Magna 750 installed new plugs but still

De-cell popping is usually caused by a lean condition. Sounds like you could use a Dynojet kit.

Posted on Sep 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i adjust the carburetor


there will be a plug at the side top of the fuel bowl that you remove to check and adjust the float level while running
the float level is adjusted by the bolt at the top of the cover above the needle and seat adjust until the fuel is level with the threads of the plug
screw that mixture screw/s in all the way then back out 1 1/2 turns
start the engine and adjust the idle speed by the screw on the accelerator lever
set to around 800 rpms
adjust the mixture screw in until the rpms start to slow
now screw the mixture out until the rpms again slow
mixture adjustment is achieved by turning the screw back in 1/2 the turns that you used to turn it out from the slow in position to the slow position out
again adjust the engine rpms by the accelerator screw to the 800 rpms
most engines idle between 700 and 850 rpms unless and efi engine which have around 850 -950 rpms range

Nov 19, 2015 | Holley 1986 86 Dodge D150 Fuel Pump-1986...

1 Answer

How do i adjust the transmission bands on a 93 toyota camry?


Adjustments - AutoZone

www.autozone.com/repairinfo/.../repairGuideContent.jsp?page...
AutoZoneBoth band adjustment screws are located on the left side of transmission, the ... 13: Automatic shift control adjustment-1989-93 vehicles with the 3.8L engine .... Ex. 04 Camry Battery See More Examples ... Explorer 4WD 4.0L EFI SOHC 6cyl; 2001 Toyota Corolla 1.8L EFI DOHC 4cyl; 2004 Infiniti M45 4.5L SFI DOHC 8cyl.

Aug 24, 2015 | Toyota Cars & Trucks

1 Answer

Vf750 honda idles but dies when throttle opened


Hi, Anonymous and the usual suspects are:
1. Idle port, transfer ports, slow air jet clogged.
2. Idle adjusting screw set too low.
3. Air fuel mixture adjustment too lean.
4. Pilot/slow fuel jet clogged.
5. Faulty accelerator pump.
6. Float level too low.
7. Float bowl contaminated old fuel, water, dirt, rust, etc.
8. Carburetor bowl vent line clogged/blocked/pinched.
9. Fuel line to carburetor kinked or pinched.
10. Fuel filter clogged.
11. Intake manifold leak.
12. The gas cap is not venting properly or fuel tank venting system blocked.
13. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
14. Needle and seat stuck closed in the float bowl.
15. Multi carburetors not in sync.
16. Faulty fuel pump.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Starts choke but dies with little throttle
1984 VF700 Magna starts but won take throttle
Honda Magna VF750C Service Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda 1995 VF750C Magna Owner Manual

Jun 14, 2014 | 1995 Honda VF 750 C Magna

1 Answer

How to adjust carburator Jeep Wrangler 4.0 258 of 1991


While engine is turned off.Screw shut both fuel and air mixture.Then each screw turn open 2 and half turn or some times 2 full turns.that should give close enough mixture .then switch engine on and make sure idle at 10rpm for auto and 6 rpm for manual.Then adjust screws lightly to your needs constant check rear exhaust for color of smoke if black it\'s too rich in fuel and if it\'s a farting noise coming out of the exhaust it\'s too lean.The sound out of the exhaust should be running continues and no missing.

Dec 16, 2013 | Crown 1991-1993 Jeep Wrangler YJ Drive...

1 Answer

How do I adjust the fuel mixture on the ford 460 efi


The mixture is not adjustable.
You have fuel injectors that are controlled by the computer.
If the check engine light is not on, I would look for a fuel pressure problem or a leaking injector.

Feb 06, 2013 | Cars & Trucks

1 Answer

GOTA 93 tr MAGNA with EFI 2.6 lookn for fuel mixture adjusting screw so i can lean mixture off its running rich


efi most probably have a mixture screw as it is fuel injected, Check oxygen sensor . air flow meter sensor, faulty injector (leaking) check for fault code in cpu

Jan 22, 2013 | Cars & Trucks

1 Answer

2003 Honda VF 750 C Magna will not idle


Hi, Roy and the usual suspects are:
1. Fuel cap or fuel tank is not venting properly.
2. Fuel filter clogged.
3. Fuel line pinched or kinked.
4. Vacuum line from the petcock to intake manifold cracked.
5. Float needle and seat sticking.
6. Float level too low.
7. Carburetor bowl vent line clogged/blocked/pinched.
8. Idle adjusting screw set too low.
9. Air/fuel mixture screw set too lean.
10. Idle port, transfer ports, slow air jet clogged.
11. Slow fuel jet clogged.
12. Faulty fuel pump.
For more information about your issue and valuable "Free" downloads that you will need please Click on the blue links below. Good luck and have a wonderful day.
Not used to V4 carbs Advice
http://www.magnaownersoftexas.com/forums/index.php?topic=5371.0
Honda Magna VF750C Service Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda 1995 VF750C Magna Owner Manual

May 25, 2012 | 2003 Honda VF 750 C Magna

1 Answer

750 magna idles too high, idle adjust is backed all the way out,still too high


Hi, Anonymous and the usual suspects are:
1. Throttle cables improperly adjusted, pinched or need lubrication.
2. Idle adjusting screw needs to be backed off.
4. Air fuel mixture adjusted too lean start with 2 full turns.
5. Intake system air leak.
6. Fast idle choke ramp is not releasing.
7. Broken throttle return spring.
8. Damaged diaphragm or slide.
9. Faulty MAP, TPS, ATS, O2, sensors or wiring/connector.
10. Multiple carburetors not in sync.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Another High Idle post
http://www.magnaownersoftexas.com/forums/index.php?topic=3454.0
Honda Magna VF750C Service Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda 1995 VF750C Magna Owner Manual

Feb 01, 2012 | 1997 Honda VF 750 C Magna

2 Answers

1997 Honda Magna 750 installed new plugs but still


seems to rich, thus the popping sound, try leaning the low speed mixture

Aug 08, 2009 | 1997 Honda VF 750 C Magna

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...