Question about 2005 Honda CR 125 R

1 Answer

Clutch is grabing

This is just a recent problem with my 97 cr 125 once started and warmed up i take of once revs build up a bit it starts reving out like i am slightly pulling in cluth lever i have checked oil level and slakened of al cabe adjusters and no help please give me some good advice would be much appreciated

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 126 Answers

Sounds like clutch disks are in need of replacement. your clutch is slipping when under a heavy load. if you have adusted the cable properly, then i would focus on the clutch friction disks. these are designed to wear as they transfer power from the engine to the transmission.

drain the oil and remove the side cover to access the clutch basket. you'll need a new side cover gasket as well as a new clutch pack (friction & metal).

Posted on Jan 27, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Honda CR 125 R very high idle


Hi, Anonymous and the usual suspects are:
1. Throttle cables improperly adjusted, pinched or need lubrication.
2. Idle adjusting screw needs to be backed off.
4. Air fuel mixture adjusted too lean start with 2 full turns.
5. Intake system air leak.
6. Fast idle choke ramp is not releasing.
7. Broken throttle return spring.
8. Damaged diaphragm or slide.
9. Faulty MAP, TPS, ATS, O2, sensors or wiring/connector.
10. Multiple carburetors not in sync.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
CR125 overly high idle at low idle settings help
Cr 125 2002 idling high
Honda CR 125R 2002 Sevice Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda Elsinore CR125M Owner Manual

Apr 17, 2014 | 2004 Honda CR 125 R

1 Answer

I've just got a Yamaha dt 125 R, I think it's a


You have to clean out the carburetor, lots of build up inside of it.

Jul 11, 2017 | Motorcycles

1 Answer

My cr125 wont idel after stating can it be ajusted.


there is a little screw at the back of your carb next to your air box. kick your bike over and keep little revs on screw it clockwise (in) then start so slowly screw it anticlockwise (out) till your bike starts to rev a bit mor then release your throttle and it should tik over.

Aug 07, 2012 | 2003 Honda CR 125 R

1 Answer

2000 honda cr 125 R when i start it when its cold it revs super high until it warms up then it idles normal. What could it be?


is that with choke on ? as some times it can rise ? or is it a primer choke , then you may have a crack in intake manifold ? ! P...

Jul 04, 2011 | 2003 Honda CR 125 R

1 Answer

I am haveing trouble with my 1996 Mazda B2300, When I start my truck after its been sitting for any length of timeI have to rev the engine to get it started, I have to continue reving until engine is warm...


Replace the temperature sending unit/sensor. This sensor tells the computer to put the engine into cold start mode and it then sets idle a bit higher and puts a bit more fuel into the engine to keep it running without having to touch the throttle. Once it's warm, sensor tells computer to go to normal run mode and it's done. No problem.

Dec 19, 2017 | 2005 Dodge Caravan

1 Answer

Beta rev 50 engine starts to stall when rev up under load if you build reves up with cluch it is ok any one with any answers it would be helpfull


Would suggest you service the carb as you may have a partially blocked main jet...otherwise I would need more information

Dec 30, 2009 | 2006 Beta RR 125 Enduro

1 Answer

1991 CR 500 (reving to high on idle high serges)


take some wd 40 & spray around the carb boot while running to see if the idle drops for a few seconds. sounds like you have an intake side air leak causing a lean condition making the motor rev high.

Feb 16, 2009 | 2001 Honda CR 500 R

3 Answers

Clutch dont work


This is a easy fix. All you have to do is let the bike warm up a few minutes before you take off. I would like you to try it your way first. Then let it warm up for 5 mins then see what happens, you can warm it up faster by reving the engine but let it run for 1 min before you rev it up. Enjoy your riding.

Dec 21, 2008 | 2006 KTM 125 SX

1 Answer

Idle goes nuts while warming up and now while driving....any help


check your throttle position sensor. this has nothing to do with your water pump. when the TPS goes out it does what your talking about. it revs up and down all the time. it is fairly easy to replace

Dec 08, 2008 | 1993 Honda Accord

Not finding what you are looking for?
2005 Honda CR 125 R Logo

235 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

77514 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...