Question about 2007 Victory Vegas 8-Ball
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
It is the speedo sensor on the drive pully on the right side of your tranny box. If you look down in the pully area you will see a small little black cylinder abut 1 inch long. Take a metic socket loosen and remove. Brand new one is around $49 i think.
Posted on Jul 11, 2009
Replacing motorcycle rear brake pads
With the weather getting nicer, a lot of motorcyclists are dusting off
their motorcycles and performing their routine spring tune up. One very
important area to check is your brakes. Otherwise it will be very
difficult to stop by just dragging your feet going 50 mph.
I will mainly focus this article on replacing the rear brake pads. This job is very simple, and takes less then a half hour. Even a government employee could do it.
1] For this step you will use a flat tip screwdriver between the pad, and rotor. Gently pry the pad outward to push the piston back in the caliper.
2] Find and remove the retaining clip on the pin. Remove clip.
3] Using a small punch drive the pin half way out. You will want to leave it so that it holds the inboard pad in place.
4] Remove, and replace the outboard pad. Make sure that it is seated in the caliper. Slide your punch in the hole so that the pad stays in place.
5] Pull pin the rest of the way out, and replace the inboard pad.
6] Re install the pin through both pads. I use a long extension, and go through the wheel to knock the pin in completely.
7] Finally, reinstall the retaining clip.
I am glad to post this and help you....... Now that I have ruined my dust cover boot trying to find a bolt to remove, to replace the pads. This is THE ONLY HELP YOU CAN FIND ON THE VICTORY REAR BRAKES ON THE WEB! Please believe me. :[ Now if any one can help me in finding a place to order the rubber dust covers for the rear brake calipers on a 04 Vegas I will be forever grateful. Thanks to all that try to help me. AND I NEED LOTS OF IT :} Ken..
Posted on Aug 30, 2009
SOURCE: 2007 Victory Hammer
G'day, from what I can see from pics, your hammer should be disc brake rear. This means there's usually no need to remove the wheel. If you have a close look at it you should be able to see how the pads are removed. Some pads are held in by pins or bolts that pass through holes in the pad to hold it in, others are held in by the caliper itself & you'll need to remove it to change pads.You'll need to sqeeze the pistons back into the caliper if you're putting new thicker pads in. You can use a G clamp & old pad to do this, just keep an eye on the fluid res.hope this helps :)
Posted on Apr 12, 2010
Tips for a great answer:
Apr 20, 2016 | Victory Motorcycles
Jun 23, 2015 | Victory Motorcycles
Sep 14, 2014 | 2011 Victory Vision 8 Ball
Jul 11, 2014 | 2008 Victory Vegas 8-Ball
Jul 15, 2012 | 2008 Victory Vegas 8-Ball
Aug 10, 2017 | 2006 Victory Vegas Jackpot
Jul 12, 2017 | 2006 Victory Vegas Jackpot
Sep 30, 2009 | 2007 Victory Vegas 8-Ball
Sep 16, 2009 | 2008 Victory Vegas 8-Ball
23 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: