Question about Motorcycles

Open Question

Throttle cable stuck on my joyner 650 sand spider bugie

Posted by on

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

A spider white with bug eyes

a photo is worth more than your vague description

Jul 10, 2017 | Lands Phones

1 Answer

I cleaned the injectors on 2006 yamaha vstar 650 got a little more power but when I open full throttle and release it some it is surging what could be making it surge now?

Hi, Peggy try running a can of fuel stabilizer (Sea Foam) in the gas tank otherwise the usual suspects are:
1. Extremely lean fuel mixture.
2. Dirt, rust, water, or ethanol sludge in the fuel system.
3. Sticky throttle cables.
4. Multiple carburetors not in synchronization.
5. TPS sensor out of adjustment or faulty.
6. Wrong spark plugs for the type of service.
7. Throttle bodies not in synchronization (FI)
8. Faulty O2 sensor.
9. Clogged, stuck, or faulty IAC valve.
10. Aftermarket components not compatible with ECM.
For more information about your issue and valuable "FREE" downloads that you will need please click on the websites below. Good luck and have a nice day.
Star 950 Surging Yamaha Star Forum
Losing power on Vstar 650

Apr 10, 2016 | Yamaha Motorcycles

2 Answers

Need download for schematics on joyner jn250

goto this link and scroll down to the bottom of the page not sure if ite the manual you are after and its saying its on ebay.....

Dec 19, 2013 | Cell Phones

2 Answers

I have a 2005 gt650s and a few days ago when i start it up its sitting at 7000 to 9000 rpm's

Check throttle cables make shure throttle shafts are closing Iuse to be a HYOSUNG dealer Give me a call 903- 917-8500 MOPAR KENNY I would like to help you

May 22, 2011 | 2005 Hyosung GT 650 S

1 Answer

I have a S21OT sand filter that is running off the pressure guage and flowing sand back into the pool. The laterals are fine, I changed the sand, backwashed for about two minutes, and rinsed, The pressure...

Usually sand blowing back into the pool is either cracked laterals, a cracked hub assembly (what the laterals screw into) or a bad spider gasket is wrong with pool filters. If you are certain that the laterals and hub are not cracked then I would try replacing the spider gasket.

Apr 08, 2011 | Hayward SAND FILTER, PRO SERIES

1 Answer

After backwashing dirt and sand blow back into the pool...the laterals look fine and sand was replaced 2-3 years ago

make sure the spider gasket in the multiport is not damaged or out of place. Also, make sure the spring is not cracked and the spider gasket seats well when it's on filter mode. If the laterals are good, this is the most likely problem.

Aug 23, 2010 | Hayward SAND FILTER, PRO SERIES

1 Answer

Motorcycle 650 Yamaha throttle problems

Check your carb there is a retaining spring holding the carb throttle lever down/back to close. Sounds it is not in its place. Good help?

May 01, 2010 | 1982 Yamaha XJ 650

2 Answers

Sticky throttle cabel

idle cable out of adjustment and or throttle cable needs adjusting also and they always need to be lubed at 5000 miles adjust throttle cable with wheel striaght forward idle cable to all the way right lock and 2-3mm free play on throttle grip

Mar 03, 2010 | 2007 Yamaha V Star Custom

1 Answer

Why does water constantly flow out of the backwash, even if the filter is on "filter"

You have sand or somthing stuck in you spider gaskit.
Take apart and clean.
Move handle around and hope it will dis-lodge iteam.
Be-careful not to damage spider gaskit 'O' ring.

Jul 11, 2009 | Pentair FILTER TANK BOTTOM, 48 SQFT

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers


Level 3 Expert

75822 Answers


Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides