Question about 2008 KTM 50 SX

Open Question

I want to remove my ktm sx50 clutch

I would like to remove the old clutch and put a new one in

Posted by Anonymous on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 31 Answers

SOURCE: i have a sx50 ktm 2001 the key keeps braking why

what seems to be the problem?

Posted on Nov 02, 2009


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Have a 2011 50sx ktm no spark getting to plug ,plenty power out of maggy to coil have put new coil and lead ,new plug but still no spark with the kill switch unplugged

Hi, Chris and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and module.
5. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
6. Faulty ignition coil or electronic control module or CDI box.
7. Faulty CKP, CMP, or BAS sensor.
8. Faulty ignition switch.
9. Tilt sensor needs a reset.
10. Security alarm failing to disarm needs reset
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
KTM 50 No Spark Mini Pe Wee
Dirt Rider Magazine
Motorcycle Message Board Motorcycle USA

Jun 23, 2016 | KTM Motorcycles

1 Answer

Fit a chain roller ktm 65

Okay you have the old one if you do find out how to remove from the person you bought the new one from remove it and put it on the opposite way simple

Feb 14, 2015 | KTM 625 SMC Motorcycles

1 Answer

KTM SX50 wont run without choke

carb is running tooo lean, remove carb and strip down, removing all internal jets, check float height setting and note number of turns mixture screw is set at.......completely clean internals in a large can of carb cleaner- available at wall mart- has a basket inside the metal container so you will not loose small parts while the carb is soaking in the mixture...leave for a day, the crean all parts and blow out with high pressure compressed air. and re-assemble, and refit.....please note, never use ethanol fuel in your motorcycle, I only use classic gas in all my vehicles...less problems

Dec 27, 2013 | 2009 KTM 50 SX

1 Answer

Problem with 09' ktm sx50 , the bike has a very bad knocking sound on low idle , but when you rev it up it goes, the sound comes from the clutch/kickstart side...? I thought at first the kick star

Hey Barry, a knocking from your engine IS NEVER something to be ignored.. BUT, if you do it will go away..WHEN IT BREAKS and your ENGINE QUITS RUNNING!!!!
Take it to a qualified professional!! please....!!

Sep 20, 2017 | Motorcycles

3 Answers

Have a 2006 ktm 250 sxf seized rod to the crank got it changed reinstalled put motor back together now can not even kick it like somthing is stuck. Toke the clutch basket out, timing gear and water pump...

Your clutch basket is the link between the engine and transmission. Your kick starter rotates the clutch basket gear, which turns another gear at the engine crank. Remove either the basket or gear at the crank and see if the engine, and the transmission both turn. Sounds like the engine is stuck for some reason. At least you can cut the issue in half.

Aug 13, 2011 | 2006 KTM 250 SX-F

1 Answer


If you just want to remove and replace the clutch plates then no special tools required just open the cover remove the pressure plate bolts and start removing old plates and then replace with new ones in exactly same way - tip with installing new clutch plates - soak them in oil few hours at least best over night before you install them back in -
If how ever you want the clutch hub and clutch basket off as well for some reason then you will need a clutch holding tool as well as you rarely could undo the lock nuts with out it
when changing your clutch plates go slowly take care and special notice to how it is all coming apart. from model to model sometimes there can be a little spacer or little spring or little ball bearing somewhere that with out care and attention may fall on the floor so go slow give notice to the order of the parts as they come out and you will have no dramas at all, as is reasonably simple job to do
good luck regards Jamie

Jul 03, 2011 | KTM 300 EXC Motorcycles

1 Answer

How to adjust ktm 530 exc-r hydrolic clutch

first you have to remove the case of clutch then you have to remove the all the bolts then you add a new one >>

Jun 12, 2010 | 2008 KTM 530 EXC-R

1 Answer

Help!!! clutch assembly 95 ktm exc 125

all the discs and plates should be the same size did you by a new clutch?

Apr 03, 2010 | 2000 KTM EXC 125

2 Answers

I have a sx50 ktm 2001 the key keeps braking why

Is the igintion switch tight to spin 'on' with the key?
If so, use some graphite powder and a little WD40 to tht switch..

Oct 25, 2009 | 2001 KTM SX 125

Not finding what you are looking for?
2008 KTM 50 SX Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top KTM Experts


Level 3 Expert

77514 Answers


Level 2 Expert

342 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Are you a KTM Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides