Question about Motorcycles

1 Answer

Looking for a site that i can go in.to view the digram for rear arm from a 2001 yamaha big bear 400

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Go to www.cheapcycleparts.com and type in your quad and there should be a place on the site to look at oem diagrams

Posted on Jan 21, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

rselvy
  • 83 Answers

SOURCE: Yamaha SRX 400

I'll post the address for you to get the manual you need and the web site has an online parts manual but it does not offer a repair manual for free. Do you still want the web URL?

Posted on Dec 12, 2008

  • 3567 Answers

SOURCE: yamaha big bear no spark

I'm not familiar with all quads and all the kill switch locations. Does it have a tip-over kill switch? Is it working? Is the quad in neutral? Is the neutral light on? Many engines will not spark if the neutral light is not on. Are the headlights off when starting?

How good is your battery? A low battery can kill spark. Test for spark by grounding the threads of the plug against the cylinder. Have a friend kick the bike while you watch for spark. Assuming no spark, then check all the kill switches with an Ohmmeter to be sure each switch is working properly. Sometimes a switch goes bad. Try disconnecting all kill switches then check spark.

Check the wiring harness, even under the gas tank and seat. Are all the connectors clean and with a tight connection? Any abraded wires? Check the ignition switch also. The switch can go bad as well. Are the flywheel coils good > is the battery getting a charge?

Still no spark? If CDI then get it checked.
If points then file or replace them along with a new condensor and reset the gap then time the engine. >> I hope this helps.

Please rate this answer. Thanks trsrhntr!

Posted on Apr 03, 2009

co7196
  • 3433 Answers

SOURCE: no front brakes on 95 yamaha big bear atv

gravity bleed. make sure fluid is always full. crack open the bleeder screw and let the brake fluid drip until no bubbles. Then close bleeder top off fluid and replace cap. Now, pull the brake handle. If there is no pressure or has bleed down, the master cylinder is kaput.

Posted on Jun 20, 2009

  • 19 Answers

SOURCE: yamaha big bear 400 will

Sounds like a problem with the starter, could be a starter fuse, relay or solenoid. The start cicuit wiring could also be damaged. If you can pull-start the motor, and it runs fine, you have pretty much eliminated any problems with the motor. Check the wires running from the start button make sure they are intact, also trace them and look for around a 1" cubed black box. This is the relay, when you push the button, if its working, you will feel the box click. Also locate the starter and do the same thing. If you feel or hear the starter click, the solenoid is working. The battery voltage could also be too low to energize the starter motor. Could also be a battery or alternator issue. Check the battery voltage and for any sounds coming from the bike when you push the start button.

Posted on Aug 21, 2009

  • 149 Answers

SOURCE: owners manual 2001 yamaha big bear 4wd

http://www.carlsalter.com/motorcycle-manuals.asp

Posted on Aug 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Or what swing arm will fit to put a motorcycle tire on it


No matter which atv model you have - take a look and measure your inside diameter for your swing arm. Salvage motorcycle yards in your area would have one somewhere - but the cruisers are shaft drive, too. If you take a look at some of the swingarm assemblies online - it'd definitely work - and worst case? A little bit of alteration - and if you keep your eyes on the like the Yamaha street cruiser swingarms - just a small drive shaft there in between engine and final driven gear - easily modified at any shop that makes or alters driveshafts/welders. These pics are from a 2002 Yamaha 1100 and a 2002 Yamaha Big Bear 400. If you look for a rear assembly your year and manufacturer odds are some of the parts will even be the same.

This is from the 1100
or-swing-arm-will-fit-put-motorcycle-4n3y21cmsqpgtsjshk50qfrx-3-0.png This is from the Big Bear

or-swing-arm-will-fit-put-motorcycle-4n3y21cmsqpgtsjshk50qfrx-3-2.png

Middle Drive Gear for the 1100:
or-swing-arm-will-fit-put-motorcycle-4n3y21cmsqpgtsjshk50qfrx-3-5.png

Middle Drive Gear for the Big Bear:

or-swing-arm-will-fit-put-motorcycle-4n3y21cmsqpgtsjshk50qfrx-3-9.png

And here's what the swingarm and wheel assembly look like for the 1100:
or-swing-arm-will-fit-put-motorcycle-4n3y21cmsqpgtsjshk50qfrx-3-14.png


or-swing-arm-will-fit-put-motorcycle-4n3y21cmsqpgtsjshk50qfrx-3-27.png

It's doable. My dad took a 69 or 70 Volkswagen Beetle, cut it up, took the front half of the front fender and the back half of each back fender, combined them and on each side was a long fender with a headlight. He didn't want it to be a beetle so he called it the widow and painted the red hourglass on the back. The front end? That's the front bottom of a hull from an old jet ski. Foot clutch, shifter in the middle, electric mirrors, stereo, new pipes, Two seater and a paint job later -

or-swing-arm-will-fit-put-motorcycle-4n3y21cmsqpgtsjshk50qfrx-3-43.jpg

Won best homemade or trike, etc. everywhere he went. Had no choice but to put the wheelie bar on it'd come up 18 inches if you popped the clutch. Sold it for just under $10k to a guy from Indiana who was down here for the Turkey Rod Run Antique Car Show in Daytona at the speedway they do every year. Saw it. Went home. Called my dad a few days later. Week's time he was loading it onto a trailer and hauling it back. I'd really appreciate seeing a picture if you get yours together. All The Best, Justin Lee, 17 South Industries, LLC

Apr 26, 2016 | Yamaha 2004 YFZ450 Base

1 Answer

2005 Yamaha Big Bear 400. How do I replace rear brakes?


Removing The Rear Brake Drum & Shoes on Grizzly 600 ...

? 5:04
www.youtube.com/watch?v=n5oO7v3nT6s
Mar 11, 2012 - Uploaded by myquadrepair
Removing the rear brake drum & shoes on Yamaha grizzly 600. ... Yamaha Big Bear Oil Change and More! - Duration: 10:43. by jfrost77hd ...

HONDA FOREMAN REAR BRAKE CHANGE PART 1 ...

? 11:49
https://www.youtube.com/watch?v=xQanZdlDCI0
Jul 17, 2012 - Uploaded by 400EX99N
HOW TO CHANGE REAR BRAKES ON A HONDA ATV. ... is this about the same for a 2004 yamaha big bear 400? Read more Show less.

Nov 03, 2015 | ATVs

1 Answer

07 Yamaha Big Bear 400 4x4. How can I replace the stator and flywheel without using special tools?


You need the special tool... it is designed to prevent damage to anything else and get it off quickly, Do your self a favor, get one or take it to the dealer and pay them to pull it.. if you break something.. OUCH,,, all that stuff is VERY EXPENSIVE!!

May 24, 2015 | Yamaha 2005 Big Bear 400 4x4

1 Answer

How do you remove swing arm on a 99 yamaha big bear 350


Easy - take off tires, then caps over axle/castle nuts if you have them.
- take cotter pins and axle nuts off both ends of axle. Right side - remove brake drum, then remove two brake shoes, simple Springs connect them, you can pull apart intact, remove any collars, washers off the axle behind brakes, then there might be 4 bolts and a plate - the other side you can see the bearing. Now - this is important - for. The side with the brakes, take a socket bigger than the threads but size of axle lip - and you place that deep socket (side with brakes!) over the threads (threads will be inside deep socket) lip of socket touches lip of axle about 2-3 inches down - hit that w a hammer and the axle will go out to the left if facing rear of four wheeler. Next - remove brake lines and breather hose for rear end.
There are bolts that attach the rear end to the swing arm (to the right) take them out and maybe the bottom guard for rear end. Then where the rear end attaches to drive shaft tube portion of swing arm there are four bolts - when all that is done you'll be able to remove rear end. Undo top bolt or you might get away w/bottom for shock - next two pivot shaft nuts - big socket like, Allen head in middle - remove nut from pivot shaft (left and right side where swing arm pivots) then takeallAllen head and unscrew two thick bolts that the pivot shaft nuts tighten to our - there's a collar and bearing in there where the bike's swing arms pivot at. I've done it a dozen times - if you have any problems or that wasn't too clear, message me, I'll dig up some tech sheets from a service manual I got on a bike that year - close to same model - same mechanics, Yamaha was pretty universal. I got a 98 & 99 Yamaha 2wd and a 96 Yamaha 3504wd. All pretty easy to work on. I have a swing arm I might get rid of from Florida and a decent rate if yours is done for and you gotta replace. I sell and buy off eBay to keep most of my toys on the trail.Good luck

Nov 20, 2014 | Motorcycles

2 Answers

I have a Yamaha 400 big bear and cooling fan won't


Start by checking the fuses... If they're fine the start tracing the wiring from the fan. Look for any burn marks, pinches, etc... If in doubt I'd recommend taking it to a professional. It's really easy to mess things up if your not sure what your doing

Mar 20, 2013 | Motorcycles

2 Answers

Is the stator on a 2001 big bear 400 yamaha four wheeler four wheel drive supposed to have oil in it


Hi, yes I think it should, quite a few 4 stroke engines do, hope this helps :)

Jan 11, 2010 | 2001 Yamaha FZS 400 Fazer

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...