Question about Motorcycles

1 Answer

What is an output(trigger) - Motorcycles

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Motorcycles Master
  • 1,669 Answers

There are several definitions:

Posted on Jan 20, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

I have a td11 it has an extra output to add a third cymbal.Can that cymbal output be split to get an extra cymbal

Info I have found suggests that the Crash trigger inputs are "piezo/switch" as required for cymbal pads using

Nov 22, 2016 | Music

1 Answer

Lincoln sp-150 idealarc will not arc any more ground output checked ok fuses checked ok incoming power 230v ok output term for + voltage to wire on spool nopower when trigger pressed.continuity from

There is a temperature activated switch near the transformer that will turn off control voltage until the transformer cools. There is also a fuse for the control voltage. That would explain why the motor won't run. There's a possibility that the trigger switch in the handle is bad too.

Oct 15, 2014 | Welding Tools

1 Answer

Have a Karcher kb4040 that continues to run constantly even when the trigger isnt pressed. Also water flows out of the detergant hose when im not pressing the trigger. Pressure seems down slighlty, not...

This is two things. One is the back flow check valve to the soap line is leaking. The other is the pressure switch on the output side of the pump.

Oct 13, 2012 | Garden

1 Answer

Jvc av-21rt28 with output supply b+ but cnt trigger

If main voltage in power supply is there---follow to sweep circuit and see if there----are filaments in CRT lighting? and do you have sound and or any brightness on screen?

need a little more information to help here.

Mar 20, 2012 | Televison & Video

1 Answer

I have a Harmon Kardon HK3490 receiver which has an input for a powered subwoofer. Next to the subwoofer output is a "link switch" which turns on the subwoofer when I turn on the stereo. What...

Connect the Subwoofer Trigger Output for each subwoofer to thecorresponding trigger input on its amplifier. This enables the subwoofer toturn on or off together with the HK 3490. To further conserve energy,when the trigger connection is made, turn the Subwoofer Link Switch onto turn the subwoofer off when the corresponding pair of main speakersare not being used, such as during muting, when headphones are beingused, or when the main speakers are turned off using the Speaker 1/2 switch

Apr 05, 2011 | Denon AVR-687

1 Answer

When the trigger is off the motor stops and starts in quick succession until the trigger is pulled again

When the trigger is off your pump is overloading your engine this would be because the unloader is not doing its job try and change the pressure output of the pump this may unstick the unloader if not it may have to be taken apart.

Feb 04, 2011 | Karcher Garden

1 Answer

I have a mitsubishi HC5000BL projector and it has an audio out put on it and they refer to it as a trigger it is and 1/8 inch headphone jack. but it wont work i went through all the settings and turn the...

The trigger has nothing to do with audio and is to activate another device with a 12v signal, for example the screen. If you run the trigger into an audio device you'll probably kill it.

There are NO audio capabilities in this unit.

Page EN-7, EN-11, EN-24


Do not use the signal output from the TRIGGER terminal as a power for other devices.

Do not link the TRIGGER terminal with an audio terminal of other device because that device may

be damaged.

The rated current for the TRIGGER terminal is 200 mA. If you use a current exceeding this rating,

a failure may occur.

For information about electric screens, please contact screen manufacturers.

Dec 31, 2010 | Mitsubishi Audio Players & Recorders

1 Answer

I have a Avital model 4100 remote car starter. My question is I have 2 wires that i cant figure out where to or what to hook them up to. The wires are on a 9 pin connection. They are the H1/4 White/Blue...

I'm not familiar with this particular model, but do you have the wiring/installation diagram for this system? If so, does the manual specify if these are trigger wires or if they are output/source wires?

They could be trigger wires to allow a secondary system to activate the remote start and they provide options for either a negative trigger or a positive trigger. They could also be outputs that will provide a negative signal/pulse or a positive signal/pulse to activate other features when a remote start is successful (such as to activate a relay to power the heated seats).

Dec 16, 2017 | 831002/4100 4100 REMOTE START SYSTEM WITH...

1 Answer

Miller 175 trigger will not feed wire very

First thing make sure the lead cable is as straight as possible. and make sure the wire has a unobstructed path. then you should check the trigger input/output switch and see if the switch is getting power to it continuously. I hope this help please rate this thank you

Mar 15, 2010 | Welding Tools

1 Answer

"protect" error

You more than likely have a problem with your power supply. Home theater receivers have many different watchdog or protection circuits. If the power supply is not output the correct voltage or is shorted that will trigger a fault. You could also have an overload condition on the output stage. Too much current drawn by the amplifier will trigger a fault.

Feb 06, 2010 | Sony Audio Players & Recorders

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4982 Answers


Level 3 Expert

80339 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides