Question about Motorcycles

1 Answer

How do I remove the Lens to change the turn signal bulb?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Filmmaker:

    Uploaded 5 video answers.

  • Expert
  • 88 Answers

Remove the mirror trim off the headlight by unfastening the screw on each side of the black trim under the windshield garnish with a Phillips head screwdriver. Pull the trim off to allow access to the turn signal screws.

Posted on Jan 19, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change side turn signal bilb on a VW jetta GLS


There are two spring clams that hold the assembly into the fender, and these are at either side of the assembly, there is usually a screwdriver slot near either side. Gently pry the assembly out, and remove the lens and back, the bulb sits in the twist assembly in the lens. Replace bulb with a clean hand, so that oil and dirt don't get on the bulb surface, pull bulb straight out from socket, and replace by inserting bulb back in socket. Voila. Replaced Turn Signal Fender light.

Mar 25, 2012 | Cars & Trucks

1 Answer

How to replace bulb in front bumper turn signal housing 1995 jag xj6


hello,
  • Identify the blown bulb. Note that if a headlight bulb has blown, the dip beam is on the outside and the high beam is on the inside. Turn off the ignition switch and light switches.

  • Open the hood and replace any blown headlight bulbs. Press the plastic spring clips and remove the bulb holder from the assembly. Pull the bulb out of the bulb holder and replace it with a new bulb. It only fits one way. Be sure not to touch the bulb's glass. Replace any parking lights at the same time, they are in the headlamp unit too.

  • Remove the front turn signal light unit in the bumper to change the turn signal bulb. Push gently on the inside edge and insert a blade between the bumper and the lens at the outside edge. Compress the spring and remove the lens. Fit a new lamp by inserting it into the plug. The side marker light is changed using a similar process.

  • Open the trunk to replace the rear fog light, stop light, tail light, reversing light and turn signal light. Remove the rear light cover and turn the bulb holder fastener 90 degrees counter clockwise. Remove the expired bulb, fit a new one and replace the parts, turning the bulb holder clockwise.

  • Thanks..

    May 21, 2011 | 1995 Jaguar XJ6

    1 Answer

    How do you change the front turn signal bulb on a 1994 ranger


    Hi there,

    Here are some few tips to help out. Firstly, remove the screws retaining the headlight and trim assembly. Then carefully rotate the headlight and trim assembly away from the vehicle, rotating the inboard side away from the vehicle. Remove the side marker, parking and turn signal bulbs and sockets from the headlamp and trim assembly. They can be removed by turning them. If you are replacing a lens, remove the retaining screws for the lens to be changed and remove it from the headlight door.

    When removed, install the removed lens assembly. Then, install the bulbs and sockets and install the headlight and trim assembly. Make sure you check the operation of the lights.

    Best of luck...

    Jan 16, 2011 | Ford Ranger Cars & Trucks

    1 Answer

    How do you change the parking lights


    Signal and Marker Lights
    REMOVAL & INSTALLATION
    Front Turn Signal and Parking Lights
    1991-96 MODELS

    1. Remove the lens upper retaining screw and the fender side retaining screw.
    2. Slide the lens assembly forward until access to the rear is possible.
    3. If necessary, unplug the bulb electrical connection.
    4. Turn the bulb socket assembly counterclockwise and remove it from the lens.
    5. Depress and twist the bulb approximately 1?8 turn
      counterclockwise, then remove it from the socket.





      Fig. 1: Remove the lens upper retaining screw and the fender
      side retaining screw
      90986p79.jpg






      Fig. 2: If necessary, unplug the bulb's electrical connection
      90986p90.jpg






      Fig. 3: Turn the bulb socket assembly counterclockwise and remove it from the lens 90986p91.jpg






      Fig. 4: Remove the bulb from the socket
      90986p92.jpg

      To install:

    6. Align the bulb's locating pins, then install the bulb in the socket.
    7. Attach the socket to the lens and turn it clockwise to engage it.
    8. If removed, attach the bulb electrical connection.
    9. Place the lens into position, then tighten the fender side and upper
      retaining screws.

    Oct 31, 2010 | 1991 Mercury Tracer

    1 Answer

    How do I change the rear turn signal bulb on a 2004 Sebring convertible?


    Peel back the trunk lining to reveal three wing nuts. Remove wing nuts to pull lens cap away from car. To remove bulb socket push on the rectangular button (the release) while pushing on the end of the socket to unlock and spin counter clockwise to release. pull out old bulb and reinstall lens cap.

    May 21, 2010 | Cars & Trucks

    1 Answer

    What all has to be done to change out a turn signal on a 82 maxim 650 thanks


    If you are talking about just changing a burned out turn signal BULB, it's a piece of cake, usually.
    Typically it is just a couple of screws that hold the lens over the bulb. Remove the screws, pop the lens off, there's the bulb. Most of them are 1/4 turn bulbs, others plug in. Read the base of the bulb and it will tell you what spec bulb it is (1156, 1157, etc.)

    Hope this helps.

    Mar 18, 2010 | 1982 Yamaha XJ 650

    1 Answer

    How do I replace the passenger side corner light and front side turn signal light?


    Front Turn Signal & Parking Lights


    7ccc73e.gif
    Remove the 2 parking light housing retaining screws ...


    9898a80.gif
    ... then pull the housing away from the vehicle far enough to remove the bulb socket from behind the housing. Turn the socket counterclockwise and pull


    a323ae9.gif
    Push the bulb in the socket gently and turn clockwise, then pull the bulb out of the socket. Note the offset retaining ears on each side of the bulb


    1. Remove the screws from the lens and separate the lens from the headlight bezel.
    2. Remove the headlight bezel.
    3. Remove the screws from the turn signal housing and pull it out.
    4. Turn the bulb socket counterclockwise 1/3 turn and remove it.
    5. Installation is the reverse of removal.


    Side Marker Lights
    1. Remove the screws from the marker lens and separate the lens from the headlight bezel.
    2. Pull the bulb from its socket in the back of the lens.
    3. Installation is the reverse of removal.

    Feb 14, 2010 | 1997 Jeep Grand Cherokee

    1 Answer

    I have a left front clearance light out how do you get it out 1


    Signal and Marker Lights REMOVAL & INSTALLATION Front Turn Signal and Parking Lights
    1. Disconnect the negative battery cable.
    2. At the rear of the front bumper, turn the bulb socket 1⁄4 turn and remove the socket from the parking brake housing.
    3. Remove the bulb from the socket; if necessary, replace the bulb.
    4. If lens replacement is necessary, remove the retaining bolts and remove the lens from the bumper.
    5. To install, reverse the removal procedures. Check the turn signal/parking light operations.
    Fig. 1: Common front turn signal/parking light mounting

    d16c14b.jpg
    Fig. 2: Twist and remove the bulb socket from the back of the turn signal/parking light lens

    8b774bd.jpg
    Fig. 3: If lens removal is necessary, loosen and remove the retaining bolts

    09f4811.jpg

    Jul 24, 2009 | 1992 GMC Sonoma

    3 Answers

    Right turn signal flashes fast. Front bulb appears to be burned


    There are 2 bolts on the top corners of the bulb lens that needs to be removed then the lens pops right out and you can change the bulb.

    Apr 06, 2009 | 2006 Pontiac Montana

    1 Answer

    Change a turn signal bulb on a 2008 Camry


    you can see two screws holding this lens assembly, remove them and you can slide the lens off the cavity.

    the wires and socket would be exposed, twist the socket counter clock wise and the bulb would be exposed.

    replace the bulb and do the reverse in installing the signal light assembly back to the cavity.


    tnx 4 using fixya,


    drcool

    Nov 16, 2008 | 2008 Toyota Camry

    Not finding what you are looking for?
    Motorcycles Logo

    Related Topics:

    51 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Motorcycles Experts

    Arnie Burke
    Arnie Burke

    Level 3 Expert

    4514 Answers

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    kakima

    Level 3 Expert

    102366 Answers

    Are you a Motorcycle Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...