Question about 2000 Honda Valkyrie Interstate

Open Question

Replace bulb in instrument cluster for Valkyrie Interstate

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 8404 Answers

SOURCE: problems with 1999 valkyrie interstate Radio

Is this a factory install?

Based on what you are saying here ... I suspect you have a faulty ground. Make sure you have a good ground.

You can test this by making a temporary ground with a wire connecting from the metal case of the radio to the neg side of your battery. This may not be a teller since you say the trouble is intermittent. Your radio will probably never give you the chance to check it peacefully. It will always work when you have the tools out!

If in doubt, install a good ground. Use a very flexible wire, at least #14 or heavier, stranded or woven NOT solid. Fasten the new ground onto the metal case of your radio - make sure you don't create any shorts. Hook the other end to a known good ground on the frame, NOT the handlebars. To make absolutely sure, go to the neg side of your battery with your new ground. Also, make sure your antenna has a good ground and is not shorting to that ground (bad leadin wire).

Let me know if this works for you.

A

Posted on Sep 21, 2009

Ad
  • 18 Answers

SOURCE: How do you replace a windshield on a 1999 Valkyrie

First I suggest that you join the VRCC club ( its FOC) and they have lots of answers on the site.

Of course it depends on the make.

Posted on Sep 21, 2009

johnamyx
  • 108 Answers

SOURCE: I have a 1999 Valkyrie Interstate. How can I check

The fastest way is to get a multimeter and set is on DC volts, get to the battery and start the bike place the leads of the meter on the battery posts and rev the motor to about 2000 RPMs you should get a reading of 13-15 volts if the system is working if you dont get that reading then you will have to check the stator,and regulator.

Posted on Nov 15, 2010

landstar377
  • 66 Answers

SOURCE: does the 2001 Valkyrie Interstate

Looking in the service manual it does NOT appear to have a low oil pressure shut down sensor. I has a low oil pressure sending unit that will turn on a light.

Posted on May 30, 2011

Testimonial: "Thank you for your help. Now I have to wonder why me bike shut down on my to work this morning. I'm leaning to some sort of vacum problem. Thanks!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On a 2004 chevy tahoe. Once the instrument cluster wire clip is detached and new bulbs are soldered on the cluster. Does the instrument cluster have to be reprogrammed ?


Shouldn't need reprogramming. I removed the cluster from my 04 Silverado and sent it in for repair and replacement of the bulbs. It was out of my truck for 2 weeks. When I got it back everything worked just fine, no problems at all.

Jan 15, 2017 | 2004 Chevrolet Tahoe

1 Answer

Valkyrie baffles missing


I found an article and a video for your source on how to replace motorcycle baffles. By following the instructions in the article I am sure that you can now replace the baffles on your motorcycle.
-Phanter
Continental Motorcycle Tires

Mar 25, 2013 | 2000 Honda Valkyrie Interstate

1 Answer

Air bag light bulb change


Airbag SENSOR light bulb? Do you mean the airbag system warning lamp in the instrument cluster?

That all depends on the YEAR and MODEL of your Lincoln. (which you did not mention)

Some newer vehicles have LED's that are an integral part of the instrument cluster. If those go out, you must replace the entire cluster to fix it. Otherwise, the instrument cluster must be removed so the bulb can be replaced.

May 07, 2012 | Lincoln Continental Cars & Trucks

1 Answer

How do i change the indicator bulbs cant get to them


Indicator bulbs for what? If you are talking about indicator bulbs in your instrument cluster, you must remove the instrument cluster to replace them. Then, it depends on what kind of car you are talking about. Some of the newer instrument clusters use non-replaceable, LED lamps. When these fail, the entire instrument cluster must be replaced or shipped out for repair.

Dec 17, 2011 | Lexus ES 300 Cars & Trucks

1 Answer

Replace dash bulbs in 96 merc cougar


you need a haynes repair manual to locate instrument cluster screws to replace cluster bulb or replace cluster if digital..

Nov 24, 2011 | 1996 Mercury Cougar XR7

1 Answer

Does the 2001 Valkyrie Interstate have a low oil pressure engine shutdown sensor?


Looking in the service manual it does NOT appear to have a low oil pressure shut down sensor. I has a low oil pressure sending unit that will turn on a light.

May 30, 2011 | 2001 Honda Valkyrie Interstate

1 Answer

I need to fix Dash air vent light -Left side - that goes on and off- How due I remove the bulb and check the wiring?


Check out the "Instrument Cluster Light Bulbs" section below:

2002 Volkswagen Passat - Repair Manual - Chassis Electrical (excerpt)

Dome/Map/Cargo Light

  1. Disconnect the negative battery cable.
  2. Remove the bulb from its retaining clip contacts. If the bulb has tapered ends, gently depress the spring clip/metal contact and disengage the light bulb, then pull it free of the two metal contacts.

To install:
  1. Before installing the light bulb into the metal contacts, ensure that all electrical conducting surfaces are free of corrosion or dirt.
  2. Insert the bulb into the holder. If the contacts have small holes, be sure that the tapered ends of the bulb are situated in them.
  3. To ensure that the replacement bulb functions properly, activate the applicable switch to illuminate the bulb which was just replaced. If the replacement light bulb does not illuminate, either it is faulty or there is a problem in the bulb circuit or switch. Correct as necessary.
  4. Install the cover until its retaining tabs are properly engaged.
  5. Connect the negative battery cable.

Instrument Cluster Light Bulbs
The instrument clusters installed on these models are one of 2 types and distinguished by the instrument lighting color, either green or blue.
On models with green instrumentation, only the control light bulbs are replaceable. Should any other failure occur, the instrument cluster must be replaced.
On models with blue instrumentation, none of the components are replaceable. Should a failure occur, the instrument cluster must be replaced.

Map Lights
  1. Disconnect the negative battery cable.
  2. Remove the bulb from its electrical connector.
  3. Installation is the reverse of removal.

Feb 19, 2011 | 2002 Volkswagen Passat

1 Answer

How do you change the instrument light bulbs?


you have to take out the instrument cluster and then twist the hold down a half turn and pull to remove bulb and hold down from cluster then remove bulb from hold down replace with working bulb and reverse to install working bulb then reinstall instrument cluster.

Feb 13, 2010 | 2003 Kia Sedona

1 Answer

Instrument cluster bulb is out. how do i replace


It may not be a bulb, as the instrument cluster usually has a number of bulbs and they probably didn't all blow at once. Pulling instrument clusters can be touchy and may not be for the average "shadetree mechanic" however, typically there are a few screws above the cluster going into the dash pad and a few hidden behind the trim panels below the cluster.

Dec 22, 2009 | 2001 Chrysler Sebring

1 Answer

Need to replace instrument cluster/AC bulbs


Hello, You can obtain a 2004 Ram Factory Service Manual with all of that information available from Promanuals.net. The reason why it may be so important is because right before the removal instructions the service manual has diagnostic instructions to try. There are numerous pages on removing the instrument cluster, and cluster bezel.

(1) Disconnect and isolate the battery negative
cable. (For Airbag)

(2) Remove the cluster bezel from the instrument
panel. (Refer to 23 - BODY/INSTRUMENT PANEL/
CLUSTER BEZEL - REMOVAL).

(3) Remove the four screws that secure the instrument
cluster to the instrument panel structural support
(Fig. 5).

(4) Pull the instrument cluster rearward far
enough to access and disconnect the instrument
panel wire harness connectors for the cluster from
the connector receptacles on the back of the cluster
housing.

(5) Remove the instrument cluster from the instrument
panel.
9e8a042.jpg

Oct 01, 2009 | 2004 Dodge Ram 1500

Not finding what you are looking for?
2000 Honda Valkyrie Interstate Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4525 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Mike

Level 3 Expert

4340 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...