Question about Motorcycles

Open Question

Kawasaki bayou 300 carb problem

Engine runs fine at idel but backfires when given trottle, will run with choke on

Posted by on

  • Robert Sonnenberg Feb 10, 2013

    Found the problem to be the carb float needle and a pluged jet. cleaned jet and purchased oem needle and runs like a champ, no backfire or gas over flow

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 66 Answers

SOURCE: 2003 yzf450 wont run right?

recheck pilot jet & pilot circuit.also check compression

Posted on Feb 16, 2009

Ad
  • 3567 Answers

SOURCE: kawasaki 300 bayou won't rev up.

No guarantees but try this. Pull the slide from the throat of the carb. Now move the clip on the jet needle down one notch. This will richen the low end mix. Two notches may be needed but do one notch at the start.

Posted on Apr 30, 2009

ollie reece
  • 1167 Answers

SOURCE: I have a 1985 Kawasaki Bayou 4 wheeler, I had took

ok buddy your not getting enough fuel in the carb so on the carb will be a screw you need to turn this mixture screw out a turn and try it if this doesnt work get back to me buddy

Posted on Sep 14, 2009

ollie reece
  • 1167 Answers

SOURCE: Bayou 300 cranks then stops after a minute

ok buddy to stop the back firing on the carb will be a screw turn this in 1/4 of a turn and try this the mixture screw on pic below

Posted on Sep 18, 2009

ollie reece
  • 1167 Answers

SOURCE: Kawasaki bayou 300 will idle ob but will not rev up

try playing with the mixture screw on the carbs this pic below will help you buddy get back to me if no difference7fe98b2.jpg

Posted on Sep 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 06 Kawasaki 4 wheeler. Backfires when light switch is on going down highway. Is it battery related ?


Problem with Brute Force, please save my 4-wheeler from shop ...

www.kawieriders.com > ... > Kawasaki Brute Force/Prairie/Bayou
Nov 16, 2011 - Problem with Brute Force, please save my 4-wheeler from shop! ....2007 kawasaki 750 4 wheeler backfire problem ... should I save for my brute force 750? moe, Kawasaki Brute Force/Prairie/Bayou, 3, 10-18-2010 06:55 PM. Backfire thru exhaust
Feb 24, 2011
Low RPM Backfire Through Carb
May 24, 2010
four wheeler keeps backfiring
May 9, 2010
06 brute force 750 poping and backfire
Feb 18, 2010
More results from www.kawieriders.com

Oct 08, 2015 | kawasaki Motorcycles

1 Answer

OK I've adjusted my Carb on my Kawasaki bayou 300 and now in order for it to run like it should the chock has to be on all the time. I can't figured this out......


Hi Abbott:
Sounds like you've almost got it! Way to go.
Odds are pretty good that the jet(s) in the carb have some gummy bits in them. I'd be considering removing the carb, dismantling it, cleaning all the bits, using compressed air to blow it all out, re-assembling it, and having another go at it.
Since it only wants to run when you choke it, it's way too lean, so needs more fuel. Somethings gotta be plugged up.

Apr 24, 2015 | kawasaki Motorcycles

1 Answer

I have a 90 Kawasaki KLF300 Bayou 4X4 and I am having a problem with it running too rich no matter what I do. I have taken the carb apart several times, reset the mixture screw to factory setting. I have...


Hey Dave,
thought I answered this already,,,??? Classic "brass kit" symptom! >>> You need a "brass kit".. this is the needle jet and the jet needle in the center of the carb. The jet needle is the thin needle that hangs down from the center of the slide... The needle jet is the "hole" that the jet needle slides into...Remove the carb, take the bowl off, remove the main jet, the needle jet holder should be able to be gently tapped out, the needle jet is a short brasspiece,, it comes out through the hole where the slide goes,,, reinstall the NEW needle jet, needle jet holder...(it may have a groove in it for correct location). once its seated, you can reinstall the main jet..NOW >> to install a new jet needle,,, remove the slide from the carb.. remove the spring and seat from the slide that holds the needle jet in place.. NOTE which groove the clip is in on the old needle.... (should be the middle one). re install the new needle, reinstall everything else and your atv WILL run fine for a long time..This is a common problem on ATV's..
you need part #'s
1990 Kawasaki BAYOU 300 4X4 KLF300 C2 Carburetor

http://www.kawasakipartshouse.com/oemparts/p/kawasaki/16009-1503/needle-jet-n36w

http://www.kawasakipartshouse.com/oemparts/p/kawasaki/16017-1270/jet-needle-6

Jun 24, 2017 | kawasaki 2004 Bayou 300 4x4

1 Answer

I have a 88' Kawasaki Bayou 300. It will start


buy a bottle of gasline anti-freeze. it will absorb any water in your fuel. add a half a bottle now and a half next time you fill the tank. should improve the operation of the engine

Jul 13, 2010 | kawasaki Full Suspension Mountain Bike Men

1 Answer

Bayou 300 cranks then stops after a minute


ok buddy to stop the back firing on the carb will be a screw turn this in 1/4 of a turn and try this the mixture screw on pic below

Sep 18, 2009 | 2001 kawasaki KLX 300

2 Answers

I have a 1985 Kawasaki Bayou 4 wheeler, I had took it to shop last year to get it running the had to clean and adjuster the carb. It set for a year with stabilizer in gas and not it is doing the same thing...


ok buddy your not getting enough fuel in the carb so on the carb will be a screw you need to turn this mixture screw out a turn and try it if this doesnt work get back to me buddy

Sep 14, 2009 | 1998 kawasaki KLX 300

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...