Question about Motorcycles

1 Answer

My suzuki gsxr 1000 k3 will start then cut out six times before it runs properly on its own in the cold

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Expert
  • 314 Answers


  1. Take Down
    • 1 Park the motorcycle on the kickstand or center stand and allow the exhaust pipes to cool completely.
    • 2 Refer to your Suzuki service manual and organize the metric tools needed to remove the baffle. On newer models, it may be necessary to remove the tailpipe section to modify the baffle. On older models, you may be directed to remove a bolt that secures the baffle in the tailpipe.
    • Follow the procedure given in the manual and remove the tailpipe section or slide-in baffle using the appropriate tools. Save any brackets or bolts. Place the tailpipe or baffle on a workbench.
    Tailpipe Baffles
    • 4 Hold one end the tailpipe up to a light and look inside the other end. Depending on the baffle, you may see very little light or none at all. Modifying the baffle is a matter of opening up areas in the baffle.
    • 5 Chuck a 1/4-inch drill bit in an electric drill. Use a bit extension if necessary to reach deep into the tailpipe with the drill bit.
    • 6 Place the tailpipe on a workbench. Use a towel or rags to prevent scratching the finish. Insert the tip of the drill bit into the tailpipe and drill a 1/4-inch hole in the baffle.
    • 7 Hold the tailpipe up to the light again. Determine the number of additional holes you want based on the purpose of the modification. Drill additional holes in the baffle if needed.
    • 8 Stand the tailpipe on end and tap it on the workbench to clear the debris from drilling out of the baffle. Make sure all debris is cleared out before reinstalling the tailpipe on the motorcycle.
    Slide-In Baffles
    • 9 Secure the outer end of the baffle in a bench vise with the baffle extending to one side. The outer end has the threaded hole where the bolt was removed to take the baffle out of the exhaust pipe.
    • 10 Measure the length of the baffle and divide it by four. You modify a slide-in baffle by cutting off a one-quarter section at a time using a hacksaw. Mark the baffle at the one-quarter point and cut the first section off the end.
    • 11 Reinstall the baffle in the exhaust pipe using the saved bolt and the metric tool.
      Start the motorcycle and determine if the modification produced the desired result.
    • 12 Allow the exhaust pipe to cool completely before removing the baffle for further modification. Most likely, cutting one or two quarter sections will give you the result you want. Avoid cutting too much off the baffle, or it will be useless.

Posted on Jan 17, 2013

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 3567 Answers

SOURCE: Max water temp and Min oil pressure GSXR 1000

I am glad you posted on FixYa. I can help on the manuals. Everything you asked for AND a parts fitch with part numbers are on the free PDF download site shown below. The 1st screen sometimes takes up to 5 seconds to build but from there the download is extremely easy.

Ya owe me a top rating on this one! Thanks Kylie!

Posted on Apr 24, 2009

  • 26 Answers

SOURCE: How fast does a Suzuki GSXR 1000 go?

Most sports bikes are limited to 300km/h by the manufacturers in an effort to be responsible. Actually the ? was about the 1000 not "most sport bikes". The Suzuki gsxr1000 for 2007 is rev limited to 184 mph. U do the math to figure out kph but in the U.S. who cares about the metric numbers.

Posted on Apr 24, 2009

  • 39 Answers

SOURCE: my suzuki gsxr cuts out after 6000revs whilst on the road

sounds like carbs

Posted on May 15, 2009

ollie reece
  • 1167 Answers

SOURCE: Suzuki Gsxr 1000

check if there is power coming from the magneto and make sure all connections are connected

Posted on Jul 08, 2009

  • 163 Answers

SOURCE: suzuki gsxr 600 06 starting problems

200° is quite warm...
If the engine wont turn over, probabily you have a bad battery, a bad starter or a bad starter relay, or bad connections.

A hot engine has more compression. If the full battery power doesn't reach the starter it won't turn over...

Posted on Aug 22, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I hot wire 2003 gsxr 1000

Hi, Timmy for this situation I would call or visit my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
How do hot wire K3 Suzuki GSX Motorcycle Forums Gixxer com
How to hotwire motorcycle
Suzuki GSX R1000 Service Manual
OEM parts for Suzuki
Suzuki GSX R1000 Owner Manual

Apr 20, 2017 | 2008 Suzuki GSXR1000

1 Answer

Cranks but will not start

Just because you have a visible spark doesn't mean that you have a viable ignition spark. The chances are, you have either failed plugs or failing leads.

Apr 24, 2013 | Suzuki GSX-R 1000 Motorcycles

1 Answer

Gsxr750 k3 missfire

Maybe the points are a bit rusty from it being parked 6 months. Maybe you washed it then parked it and water got onto those special parts. Open The cover to the points and with a piece of fine emery cloth, sand between the contacts. Also maybe new spark plug. You barely just broke the bike in.

Jun 25, 2012 | 2006 Suzuki GSXR 750 20th Anniversary

1 Answer

I have a 2007 gsxr 600. When i start it up and its cold it runs fineas soon as it heats up to temp it starts sputtering and loses power and it dosent idle very well like its missing bad pls help thx

You get any help on this problem? My bike is doing the same thing - Also, when it gets hot and turns off I can't get it to start back up all the time... Starting cold usually gives no issues -

May 20, 2010 | 2005 Suzuki GSX-R 1000

2 Answers

I have a 97 suzuki gsxr with 17000 miles i have problem starting it in the mornings

when you turn the ignition on, turn it on till you hear the fuel pump but dont start it. If you do that about five or six time and it starts, then you have air getting into your lines at night and the system is repreasurizing in the morning. Also could just be the cold start valve/injector is cloged or old.

Feb 09, 2010 | 1997 Suzuki GSX-R 600

1 Answer

Clutch k6 gsxr 1000

Proper oil is very important to wet clutches.Check to see if the oil is proper.

Jun 10, 2009 | 2006 Suzuki GSX-R 1000

3 Answers

How fast does a Suzuki GSXR 1000 go? 2002 gsxr 1000r started fine loaded it on trailer went to town came back went to unload it and it would not start was running great turns over good lots of fuel no f1...

Most sports bikes are limited to 300km/h by the manufacturers in an effort to be responsible. Actually the ? was about the 1000 not "most sport bikes". The Suzuki gsxr1000 for 2007 is rev limited to 184 mph. U do the math to figure out kph but in the U.S. who cares about the metric numbers.

Apr 24, 2009 | 2002 Suzuki GSX-R 1000

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

299 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers


Level 3 Expert

75066 Answers


Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides