Question about 2002 Honda VT 750 DC Shadow Spirit

1 Answer

Kill switch problem - 2002 Honda VT 750 DC Shadow Spirit

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 117 Answers

Well, if you could specify the problem, I would be able to help you with it :)

Sincerly, a fellow motorcyclist

Posted on Jan 17, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where does the kill switch wires go


Coil too the kill switch , kill switch too the ground good clean metal.. Kill switch is just making the ground conection.. Goodluck..

Aug 11, 2014 | Husqvarna , No.455 Rancher, 20" Gas -...

1 Answer

How to replace a kill switch on a husky 288 xp


There should be only 1 screw and one wire connecting the kill switch. The kill switch simply grounds out the ignition. So it is difficult to install improperly. The wire coming from the switch goes directly to the ignition module.

Jun 21, 2014 | Husqvarna 288 Kill Switch Wire Chainsaw...

1 Answer

How do you wire in a kill switch


just eliminate and cut off the wire to the existing kill switch the put any kill switch you want on it and take the main electrical lead to the ignition or what ever it is and put the new kill switch in the middle of the new kill switch you installed I did it before it always works just make sure to eliminate the old kill switch and its connections are no longer needed

Oct 30, 2012 | Coleman Electrical Supplies

1 Answer

Is the kill switch an open switch or is it closed,on the MB3202 McCulloch leaf blower


most units they ground out the coil to kill the engine

Aug 11, 2012 | Garden

2 Answers

No spark


Eigther the kill switch failed or ignition module. Disconnect wire to kill switch if you get spark then switch is bad. Still no spark with kill wire disconnected ignition module quit.

Sep 29, 2010 | Mtd Garden

1 Answer

I replaced ignition coil on a Tecumseh Toro 20018 mower. It would not start without disconnecting green "kill" wire. Now what do I need to do - replace the kill switch? Is the kill switch located on the...


It is a short in the kill switch, or the wire running to the kill switch. check insulation on the wire running to the kill switch and check the routing of the wire to insure that it is not being rubbed by moving parts, or the insulation melted by hot engine parts such as the exhaust system. Finally check that the kill switch itself is functioning properly with a test light or OHM Meter.

Aug 12, 2010 | Toro Garden

1 Answer

I want to put a kill switch on a Honda EM5000x


I do not understand why you would want another kill switch installed. It already has a kill switch for the engine and a circuit breaker that kills the output power. d87e9a3.png
af9e086.png

Apr 25, 2010 | Electrical Supplies

1 Answer

92 Cb250 Nighthawk won't start


Check the side stand kill switch. It kills the engine so that you don’t start out with the side stand down. If broken or out of adjustment, it would kill the spark. Check for a broken wire at the side stand switch and coupler. Try moving the kill switch by hand. If that doesn’t work then wire a jumper around the switch to bypass it. Check the fuses. Is the handlebar kill switch on? Check the operation of the ignition switch and all kill switches with a volt ohmmeter.

A “very helpful” rating for this answer? Thanks!

Jun 17, 2009 | 1992 Honda CB 250 Nighthawk

1 Answer

My gilera runner has nt got a spark i have changed the magneto flywheel spark plug but still no spark what could it be?


Check the side stand kill switch. It kills the engine so that you don’t start out with the side stand down. If broken or out of adjustment, it would kill the spark. Check for a broken wire at the side stand switch and coupler. Try moving the kill switch by hand. If that doesn’t work then wire a jumper around the switch to bypass it. Check the fuses. How good is the battery? Try a jump start from your car battery. Is the handlebar kill switch on? Check the operation of the ignition switch and all kill switches with a volt ohmmeter.

Jun 11, 2009 | 2005 Gilera Nexus 500

Not finding what you are looking for?
2002 Honda VT 750 DC Shadow Spirit Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

77194 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...