Question about Motorcycles

Open Question

06 gsxr 750. What is the skinny rod in this picture? I took off my front sprocket cover and inside is this! It will turn either direction! Is it supposed to be tight or free to spin? What is it for/do?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2336 Answers

SOURCE: How to remove front sprocket?

socket size is 36mm on older R1's .i dont think its changed for the newer model. u will probably need an air impact to remove it. puting the bike in first gear wont help. or u can ask somebody to push on the rear brake. if u got no air impact tool , u can put a big piece of wood between the wheels spikes and the swingarm to stop the rear from turning . use locktight when putting it back!

Posted on Nov 10, 2008

Ad
  • 3567 Answers

SOURCE: clutch push rod broke !!!

Chances are the prior owner installed some aftermarket springs that are too strong. This puts extra pressure on the push rod. Just pull the left and right cover of then remove the clutch assembly. put the new rod in from the left side then re-mount the left cover. Put the clutch back on then the right cover. The parts book shows a two piece push rod assembly. I wonder if a hardware store rod was installed because the factory rods are near impossible to find. The substitute rod probably couldn't handle the pressure and heat.
If not found elsewhere, google motorcycle salvage suzuki and see if you can find a used rod set.

2ff0b1f.gif

Posted on Sep 22, 2009

Testimonial: "thanks for ur help , if anymore grief i email you thanks again"

  • 185 Answers

SOURCE: how do you change the clutch on a 06 gsxr 750

It would probably be best to take the bike to a reputable mechanic and have them change it. It is not a difficult job but some specialist tools might be needed.

Posted on Nov 13, 2009

  • 1 Answer

SOURCE: 05 GSXR 750 Speedometer Reads 0

I just had the same problem 2004 gsxr 750. After massive troubleshooting and time I found out it was the gauge. So I then ebayed a gauge on ebay and bought on for 290 dollars. Speedo now works. I am just off on the actual speed, need to by a speedo healer.

Posted on Dec 06, 2009

  • 3 Answers

SOURCE: 07 gsxr 750 backseat won't unlock

When this happened with my bike, I took a large gem clip, straightened it out, and then put a 90 degree bend about 1/4" from one end. I could insert the end with the bend under the seat and use it to grab the release mechanism and pull it so the rear seat released. Then I was able to connect the cable from the latch/lock correctly to avoid the same prob when the seat was reattached.

Posted on Apr 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I pull the clutch lever and it wont disengage. Before i ave done some work on it, pull out the front sprocket cover and took out the push rod (chain sprocket change), put back the cover in place than the...


Drain the oil and Pull the clutch cover off. That rod connects to the clutch push button. sounds like it fell out. Undo all the little clutch cover bolts. Carefully pull the cover off leaving all the clutch plates in a stack as some are different to others usually the first or last plate .Check the center of this plate as that is where the button usually is. Put it all back together and check clutch with cover off. You should see it move away as you pull the lever. Make sure you back off your clutch first. Hope this helps cheers

Oct 23, 2013 | 2004 Suzuki GSX-R 750

1 Answer

06 GSXR 750 I TOOK FRONT SPROCKET COVER OFF. BUT BEFORE I DID THAT I TOOK THE BOLT LOOSE HOLDING TO THE GEAR SHIFTER IN FRONT OF THE SPROCKET COVER. HOW COME MY BIKE WON'T SHIFT INTO ANY GEARS NOW?


If you have repositioned the shifter arm correctly and it is not contacting something it is possible that you do not have the cover on correctly. There are, I believe, 2 dowel pins in back of the cover where it contacts t the crankcase if these dowel pins were not seated properly when you tightened the cover bolts it would cause the cover to misalign where the shaft goes through it and bind the shaft from rotating. Re check the cover installation.

Jan 16, 2013 | Motorcycles

1 Answer

2002 Honda VT 750 CD Shadow remove the front sprocket cover


Hi, David for this scenario you will need your service, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need for viewing and printing please click on the blue links below. Good luck and have a wonderful day.
Removing front sprocket cover
Honda Shadow Spirit 750 Sprocket Mod How to Replace Chain and Sprockets
Honda 1998 VT750C Service Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda VT750C Owner Manual

Jun 30, 2012 | 2002 Honda VT 750 CD Shadow A.C.E. Deluxe

1 Answer

Hi, i have a 1996 gsxr 750 srad and was wondering where the sensor for the speedo was?


Hello,
The speedometer sensor is located in the countershaft sprocket cover. This is the cover at the lower left rear of the engine. If you are having speedometer problems, be sure and check the speedometer rotor that is on the end of the countershaft. They have come loose and caused problems.

Jan 02, 2011 | 1996 Suzuki GSX-R 750 T

1 Answer

When i turn the key to start it wont is a neutral safety switch in column


The neutral safety switch is located inside the the case cover where the front sprocket is. Should be just below the sprocket.
D.

Sep 30, 2010 | 1978 Suzuki GS 750 E

1 Answer

How to install chain buffer on a 95 gsxr 750 ws


pull front sprocket gear , buffer installs behind gear

Feb 23, 2010 | 1995 Suzuki GSX-R 750 WS

2 Answers

I have a rattling sound in the engine of my 750 suzuki gsxr. it cranks and runs but sounds like something is broken and rattling around inside


Sounds like a Saturn engine that died at 57K miles when it dropped a rod cap while only starting the piece of junk.

Nov 14, 2009 | 2000 Suzuki GSX 750 F (Katana)

2 Answers

05 GSXR 750 Speedometer Reads 0


I just had the same problem 2004 gsxr 750. After massive troubleshooting and time I found out it was the gauge. So I then ebayed a gauge on ebay and bought on for 290 dollars. Speedo now works. I am just off on the actual speed, need to by a speedo healer.

Sep 17, 2009 | 2005 Suzuki GSX-R 750

2 Answers

1998 gsxr 750 speedo problem


if the speedo doesn't work through a cable then it probably works on a electronic sensor.try and trace the wire from the back of the speedo to the sensor and replace the sensor.will more than likely be around the front wheel area or the gearbox.

Mar 05, 2009 | 1996 Suzuki GSX-R 750 T

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...