Question about 2001 Honda CBR 929 RR Fireblade

1 Answer

Warning lights on dash of my cbr 929 rry

My honda cbr 929 rry dash warning lights are flashing 3 long flashes and 4 quick flashes

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Expert
  • 314 Answers


    • 1 Place a rear stand under the motorcycle's swing arm to support it.
    • 2 Remove the right side fairing panel from the motorcycle, using a 5 mm Allen wrench to unscrew the fairing's bolts. Pull the fairing slightly away from the motorcycle. Reach behind the fairing and unplug the right front turn signal. Set the fairing aside.
    • 3 Shift the motorcycle into neutral and start the motor. Let it warm up for three minutes, then stop the motor.
    • 4 Place an oil pan beneath the drain plug on the bottom of the motor, centered between the exhaust pipes. Unscrew the filler cap from the clutch cover on the right side of the motorcycle.
    • 5 Unscrew the drain plug, using a 17 mm socket and a socket wrench, and drain the motor's oil into the oil pan. Clean the drain plug with a shop towel and reinsert it into the motor. Use a torque wrench to tighten the drain plug to 22 foot-pounds.
    • 6 Use an oil filter cap wrench to unscrew the oil filter from the right side of the motor.
    • 7 Spread an even coat of 10W40 motor oil over the new oil filter's O-ring. Screw the oil filter onto the motor by hand. Use a torque wrench to tighten the oil filter to 20 foot-pounds.
    • 8 Place a funnel into the clutch cover's filler. Pour up to 3.3 quarts of 10W40 motor oil into the motor. Remove the funnel and screw the filler cap into place.
    • 9 Reinstall the right side fairing panel, using a 5 mm Allen wrench to insert the fairing's bolts.
    • 10 Lower the motorcycle from the rear stand and rest it on its kickstand.

Posted on Jan 16, 2013

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 301 Answers

SOURCE: having trouble with my honda 2001 cbr

There are several possible causes; fuel mixture is too rich, air filter is clogged, or worn piston rings and/or valve guide seals. The latter, however, will most likely produce blue smoke - under acceleration means worn rings, blue smoke under deceleration means bad valve guide seals. Also make sure that the crankcase vent is not obstructed as this will tend to force oil up, past the rings and into the combustion process.

Generally, an examination of the spark plugs will give you a good clue as to what the offender is. Black, sooty spark plugs indicates too much fuel (clogged air filter or mixture too rich). Oily spark plugs means worn engine parts, as mentioned above.

Posted on Oct 27, 2009

cape cod bob
  • 292 Answers

SOURCE: 2002 cbr 954 red light on gauge blinks

sounds like the engine management fault code signal. there is a free download service manual here. with it you should be able to decifer it

Posted on Apr 04, 2009

  • 408 Answers

SOURCE: my cbr 929 honda is overheating how do i fix this problem

Check the coolant circuit that does not have air at all kept inside.
With the bike cold and the radiator cap open on the bike's kick stand start pressing again and again the coolant pipes and fill in coolant if you have to.Then start the bike without closing the radiator cap and keep pressing-releasing (like a sponge) the pipes until the radiator's lower pipe start getting hot.Then close the cap and wait with the engine running until you hear the radiator fan turn on.If you reach 227 F (108 C)and it hasn't start turn it off and check the temp switch on the radiator or the fan.
If the radiator's lower pipe never get's hot but the temp gauge shows you the temp reaching above 194 F (90 C) then you have a thermostat problem and you should check your cylinder head gasket too for compression failure.

Posted on May 26, 2009

  • 3567 Answers

SOURCE: FI light comes on. Honda CBR 600

FL stands for Fuel Injecton. Your fuel injection sensors have found a problem and the onboard computer chip is telling you. You must have a dealer read the computer code to find out what the problem is.

Posted on Sep 23, 2009

  • 425 Answers

SOURCE: reset computer honda cbr 929

There is a manual at , good luck

Posted on Jan 05, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why is the red light flashing 3 long, 5 short?
Download the above. Page 125 explains it all. The 3 long means 30 and the short 5 means 5. Fault code is 35 (30+5)

Apr 19, 2015 | 2001 Honda CBR 929 RR Fireblade

1 Answer

I have 01 honda cbr929 the fi light is on and the red check engine light flashes

FI means a fault in your ignition/fuel injection system, look up fault codes online they will pinpoint the fault for you. page 125 has list of fault codes . Do you have a Power Commander fitted? these can bring there own problems, try unplugging it all back to standard to see if fault goes away.

Aug 17, 2014 | 2001 Honda CBR 929 RR Fireblade

1 Answer

2001 Honda CBR 929 RR Fireblade no headlights, taillights and gauge lights

Hi, Thomas for this scenario you will need your service/owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Headlight Dash and turn signals out CBR Forum Enthusiast forums for Honda...
Honda CB Owners Manuals

Jun 25, 2017 | 2001 Honda CBR 929 RR Fireblade

1 Answer

What are the best springs and oil


Oct 25, 2009 | 2000 Honda CBR 929 RR Fireblade

1 Answer

Head bolt torque settings

This is for the 10 main bolts, yes?
51Nm or 38 ft-lb.
the two 8mm flange bolts are 24NM /17 ft-lb

Aug 11, 2009 | 2000 Honda CBR 929 RR Fireblade

1 Answer

Red light flashing ????

it may need to be "reset" in which case you just unhook the battery for about 15 minutes. what i wanted you to check tho was the voltage of the battery. 6 or 12 volt

Jun 26, 2009 | 2001 Honda CBR 929 RR Fireblade

1 Answer

2008 blade fuel injection warning light remains on when riding. when turning on ignition light flashes 3 x slow and 4 x fast.

The flashes are what is called a 'blink code' - in your case indicating Error No. 34

Error 34 is the ECV (exhaust control value) POT voltage.

Check is the 6-pin black connector to the EGCA (the valve actuator).

Hope this helps.

Jun 13, 2009 | 2008 Honda CBR 1000 RR Fireblade

1 Answer

Red warning lights

do you have a power comander or any other type of accesories is the warning indecators on you digital gauges popping up

Feb 14, 2009 | 2000 Honda CBR 929 RR Fireblade

Not finding what you are looking for?
2001 Honda CBR 929 RR Fireblade Logo

516 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers


Level 3 Expert

75077 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides