Question about 1972 Yamaha DT 360

1 Answer

I have a yamaha 360 motor, in a flat track frame. Don't know what model it came in, it has a ser.#484. Any help would be great. Dale/

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Expert
  • 314 Answers

  1. Apply the Clutch
    • Pull the left-hand clutch lever back to engage the clutch for starting. Shift the engine into neutral by upshifting to the middle position on the foot peg on the left side of the bike.
    Insert the Key
    • Insert the key into the ignition and turn the key to the "on" or "run" position.

    Turn on the Fuel
    • Turn the stopcock on the fuel line to the "on" position to allow fuel to enter the engine of the 250 DT.
    Start the Engine
    • Fold out the kickstart lever and press down on it rapidly with your right foot until the engine starts. This may take multiple tries on a cold engine. Once the engine has started, rev the throttle to warm up the engine.

Posted on Jan 16, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Wiring diagram racing banshee

The best thing to do would be to get the diagram for a RD/RZ 350LC and the diagram for your KX and use this for comparison. There is no such thing as a "Banshee" diagram. It is a custom built motor, made using a Yamaha RD LC engine.

Dec 11, 2011 | 1986 Yamaha RD 350

1 Answer

I have a curtis mathes model plef398ccd how much would it cost to buy this T.V.

$50 work great but frame cosmatic don't look that great.$75 buck,if still in exellent conditions as tv work and vey good condition cosmatic looking frame.

Aug 31, 2011 | Curtis-Mathis CM27101S TV

1 Answer

I have a new Whirlpool AC model ACQ 128 GPW. It does a super job of cooling but what is the best way to dehumidify without using the cooling system or is this a very poor way to dehumidify? You have...

Dale, my best advice is do not operate the cooling function and the dehumidifier at the same time. The dehumidifier will generate heat, which will cause the AC to have to work harder. It's best to operate them separately. Besides, the AC works somewhat like a dehumidifier, so it's extracting some moisture anyway.

Hope this helped you Dale. Thanks for choosing FixYa, again.

Jul 21, 2011 | Whirlpool ACQ128 Air Conditioner

2 Answers

I have hooked the red, white and yellow jackes up to my new vizio tv. I just don`t know what botton on the remote I`m supposed to hit in order to get the tv on video. Thank you for any help you can give...

I should be either the 'SOURCE' or 'INPUT' button on the remote to get to the AV1 or AV2 video input jacks that you are using.
Model of the VIZIO? May be you need to look at the user manual or download it fom VIZIO web site.

Jun 08, 2011 | Televison & Video

1 Answer

Rear window of my toyota 94 forerunner is off track.Is it something that I could fix myself,and if so could you explain how.

yes. its of medium difficulty. first you will need to open the rear hatch. Locate the screws (probably 4 or more) (some may be under little plastic covers that you can take off with a flat head screwdriver). next when all the screws are removed, you'll need to pry the plastic panel on the frame. (don't have to pull extremely hard, check for screws you might have missed). use a plastic pry bar so you don't make marks. the panel will literally "pop" right off. There might still be some light or switch connectors on the panel so it might be dangling. unclip the connectors and set the plastic panel down. now you can see into the hatch frame where the window is and the window regulator (the rail that the window and motor is on). try finding where its loose and screwing it back on. if you notice anything is broken, its probably the window regulator linkage. You will need to get that replaced (buy a new rear window regulator). before installing the new window regulator, take the motor off the old one and put it on the new regulator while out of the car. then install, screw on the window, plug in the connectors and make sure it works. it sounds complicated but its a lot easier then it sounds. Good Luck! If you don't want to attempt this take it to a local shop, its a pretty inexpensive fix. if you hear the motor running, it probably doesn't need a window motor just the regulator.

May 04, 2011 | Toyota 4Runner Cars & Trucks

1 Answer

I have two 36 volt 107 lb thrust Great White motors mounted on the port and starboard sides of the polling tower of my flats skiff. My fishing application has changed and I wish to mount one of the motors...

Yes it should do, this is the bracket

Motorguide MGA515A2 Great White Troll Motor Removable Mount 17031 eBay

schematic of parts

this is the installation instructions for the Gator 360

Jul 23, 2017 | MotorGuide Boating

1 Answer


Could be you have a RT 360 frame, with a DT 360 motor in it. The RT was before the DT. Do some searching on the net for yamaha RT models.

Nov 20, 2010 | 1973 Yamaha DT 360

2 Answers


Go to the web page link below

Hope this helps

Sep 24, 2009 | 1974 Yamaha DT 360

2 Answers

01 motor in 03 frame

for 02 yamaha put the balky yz426f tranny in the yz250's, just for duribility tho....other than that yamaha manufactures might do a slite rejetting, maybe a head compession change, and other small changes. the yz line around that time were great bikes, and still are, so there was really no flaw and nothing really had to be changed because the yz250 of any year was a bulletproof bike. the only flaw i can think of is that these 01 -03 yz"s were only a few years off from having the plug and play aluminim frame, which to me pretty sweet. good luck

Feb 01, 2009 | 2003 Yamaha YZ 250

Not finding what you are looking for?
1972 Yamaha DT 360 Logo

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts


Level 2 Expert

314 Answers


Level 3 Expert

1216 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1165 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides