Question about 2005 Yamaha WR 450 F

1 Answer

Oil quantity WR450 2005

I read your answer to the question of the oil quantity.
You said to put in about 1 liter of oil.
Is this with or without the extra oil needed when changing the oil filter?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 677 Answers

Thr filter takes about 150-200 mls of oil.The bike has a dipstick to indicate the oil level.Its a good gauge

Posted on Aug 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much oil should i put back in the fork after a seal change on a 2001 mx 50


The Marzocchi Workshop: oil quantity's & levels

marzocchiworkshop.blogspot.com/p/oil-quantitys-and-levels_858.html
Oil quantity's are measure in volume in 'cc', always use a narrow measuring jug for ...MY, Fork, Measurement, RH, LH .... 2001, Z-1 MCR QR20+ 01, Height (mm), both legs, 50 .... 2003, MX PRO COIL c.105 SSVF, Height (mm), both legs, 50.

Aug 19, 2015 | Motorcycles

2 Answers

How much oil do I put in


put a bit in at a time and check the dip stick untill it is at the full mark

Jan 09, 2015 | Motorcycles

1 Answer

Waiting for ever for manual, so in mean time I've just bought 1992 Yamaha XJ900, what oil is needed plus quantities please?


10W40 semi synthetic is best the quantity is normally shown on the engine cover on Yams. My little yam and my Suzi SV have oil level windows in the right side engine cover. These show marks for low and full. Open the oil filler make sure the bike is upright and fill to the full mark,.start the bike run for a little while and recheck/refill as required. Keep checking over a few days just to make sure.

Most bikes 500cc and over have an oil capacity of approx. 3 to 4 liters.

Sep 02, 2014 | Motorcycles

1 Answer

Xt660z tenere. Infomation on fork oil weight and quantity required please.


Thank you for the inquiry.
Capacities Fork oil per rod: Oil w/o filter: 2,5 L. SAE 10W Oil incl. filter: 2,6 LITER Brake fluid: DOT 4 Final drive: Fuel: 23,0 LITER SUPER Coolant: 1,2 L. + 0,5 L.

This information should be in your owners service manual. If you did not get one with the bike your Yamaha dealer should provide one at no charge.
Hope this helps helps. Please keep us updated and remember to rate this answer.

Jun 04, 2011 | 2011 Yamaha XT660Z Tenere

2 Answers

I have a 2003 suzuki rm125 cc. i don't have a manuel. how much crankcase oil do i need to put in it once i drain it...also, i just bought 10w-40 for a four stroke will that work


quantity is .75 liters, and no, that oil will not work. You have a very high revving engine. You need to get yourself oil for a race engine. Take a trip to your local bike shop, they will have what you need. Even if they dont sell suzuki, its not specific to the manufacturer

Mar 06, 2011 | 2003 Suzuki RM 125

1 Answer

I have a 2002 Honda VT 1100 C2 Sabre and I just flushed all of the oil out of the pan and also changed out the filter. How many liters of motor oil do I have to put back into the reservois?


I have checked my service manual and it does not state quantities just top up the oil until the glass level is up to the mark. Don't forget the oil filter will take a little extra oil.
Sorry

Feb 01, 2011 | 2002 Honda VT 1100 C2 Shadow Sabre

2 Answers

How much oil does the wr426 hold? (1.2 liters ?) is there a special trick to changing the oil? the bike appeared to be low on oil...i added some, then it registered way above full. I drained the oil from...


It usually holds 0.8 lit and owners just put a liter on it!
Did u drain ur oil when u have cold engine?
U should heat up ur engine first before draining it!
hope that might help ya!

Nov 07, 2010 | 2001 Yamaha WR 426 F

2 Answers

I have bought a 2nd hand pulsar 150 2006 it has got an overheating problem and the engine is very rough (too much vibration)


its either too lean(runs hot, causes vibrations, hesitates on acceleration) or there is a problem with the lubrication system(not enough oil to the piston = alot of friction=running hot. hope that helps

Jun 14, 2010 | 2006 Bajaj Pulsar 150

1 Answer

Oil how much oil do i need to put in when i change it and what other thing do i need to change and if u could tell me what kind of oil is recomended for thet bike thank you 


Clean or replace the oil filter screen shown below. Use 10w40 motor oil. NEVER use synthetics or oils with "Special" additives. Technically, the oil quantity is .95 US quarts. Just put in the whole quart can and you will be fine. Please rate my answer. Thanks
e1d234a.gif

Jan 10, 2010 | 2002 Honda XR 200

2 Answers

How manny oil in 10 liter fuel


The bike will actually be running leaner at 32:1, than at 40:1.

You need to put 250 ml to 300 ml

Regards

Nov 27, 2009 | 2003 kawasaki KX 125

Not finding what you are looking for?
2005 Yamaha WR 450 F Logo

Related Topics:

600 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1128 Answers

D. E. Hev

Level 3 Expert

1059 Answers

mikeuk

Level 2 Expert

61 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...