Question about Motorcycles

1 Answer

06 GSXR 750 I TOOK FRONT SPROCKET COVER OFF. BUT

06 GSXR 750 I TOOK FRONT SPROCKET COVER OFF. BUT BEFORE I DID THAT I TOOK THE BOLT LOOSE HOLDING TO THE GEAR SHIFTER IN FRONT OF THE SPROCKET COVER. HOW COME MY BIKE WON'T SHIFT INTO ANY GEARS NOW?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 157 Answers

If you have repositioned the shifter arm correctly and it is not contacting something it is possible that you do not have the cover on correctly. There are, I believe, 2 dowel pins in back of the cover where it contacts t the crankcase if these dowel pins were not seated properly when you tightened the cover bolts it would cause the cover to misalign where the shaft goes through it and bind the shaft from rotating. Re check the cover installation.

Posted on Jan 16, 2013

  • Ray Jan 17, 2013

    It wouldn't shift up or down until I turned it on! Then it would shift again while not running. The problem was I didn't start the bike after putting it back together. Very strange for it to work out this way.
    Now I have a new question? I already posted.

×

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 65 Answers

SOURCE: v-rod gear shifter won''t click back up

sounds as though your gear lever return spring has broken and will need replaceing

Posted on Dec 29, 2008

  • 185 Answers

SOURCE: how do you change the clutch on a 06 gsxr 750

It would probably be best to take the bike to a reputable mechanic and have them change it. It is not a difficult job but some specialist tools might be needed.

Posted on Nov 13, 2009

Adrian762
  • 425 Answers

SOURCE: When I shift my 02 GSXR 600 the gear shift lever gets stuck

Get yourself a repair manual and find out what it says, but I think you are correct, the return spring is either broken or it has slipped. Try this site for a freebie manual:
http://www.carlsalter.com/motorcycle-manuals.asp

Posted on Jan 28, 2010

  • 97 Answers

SOURCE: My suzuki gsxr 750 sat all winter and i didnt

check spark plugs,check for spark. check fuel is good. possible needle and seat gummed up in carb float bowl. disasemble and clean with brake or carb cleaner.do not change float level. re assemble ,you can use the cleaner to help to fire the motor with a shot through the carb. make sure you cleaner says flammable. good luck.

Posted on Mar 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

20002 Road king will not fully engauge into 1st gear


Check the position of the shifter arm. It should be sitting just behind the front bolt on the transmission cover plate. If it is not then the shifter arm has likely been loose and rotated on the shifter shaft.

Mar 17, 2013 | 2002 Harley Davidson FLHRCI Road King...

2 Answers

My 2001 suzuki gsxr 750 won't downshift all of a


Your shifter cam bolt has backed out, this is a common problem on earlier GSXR's. Happened twice on my 2000, both times during race weekends.

Stop riding the bike and shifting at all and do the following repair:

Remove clutch cover - you'll drain some oil so make sure you have a drip pan underneath

Remove the 5 the clutch housing plate bolts - careful as they have pretty stiff springs behind them providing torsion

Remove all the clutch plates - make sure you keep the same order and re-install the same way; matter of fact if you have never replaced your clutch plates, do it along with this repair.

Once the clutch case is basically empty, you will see at the lower left a small assembly that looks a bit like a tuning fork, at the end of the shifter shaft. There is also a cam there with rounded cogs. There is a 8mm or 10 mm hex head bolt that holds this cam, and I'm sure it has backed out and is causing the cam and shifter to not engage the gears properly.

Remove the cam bolt. Spray some compressed air or even a light spray of brake cleaner in the threaded area where the bolt you just removed is. Make sure the threads are clean and dry.

Place the cam bolt and assembly back in its position, and take some RED loctite to the shifter cam bolt threads. Make sure to torque the bolt to specifications, I think it's 24 or 28 nm.

Let the bolt set for 24-8 hours, then reassemble the clutch and replace the clutch cover gasket. Top off the oil and go riding.

Jun 18, 2011 | 2001 Suzuki GSX-R 750

1 Answer

Hi, i have a 1996 gsxr 750 srad and was wondering where the sensor for the speedo was?


Hello,
The speedometer sensor is located in the countershaft sprocket cover. This is the cover at the lower left rear of the engine. If you are having speedometer problems, be sure and check the speedometer rotor that is on the end of the countershaft. They have come loose and caused problems.

Jan 02, 2011 | 1996 Suzuki GSX-R 750 T

1 Answer

I have A 2000 zx600j and I took off the rear tire to change the sprocket. My mistake was doing the back before the front sprocket and I've already cut the chain. Now I'm having a heck of a time breaking...


You will need an impact gun to break it loose, how are you holding the sprocket still, any moving absorbs the torque you apply and stops the breaking loose of the sprocket.

Nov 01, 2010 | 2001 kawasaki ZX-6R Ninja

1 Answer

My speedometer on my 05 gsxr 600 stopped working what do I need to check before buying a new ome


when you say stoped workig do you mean no digital desplay at all when you turn on the ignition, does this bike have an aftermarket gear indicator,? remove the screen and check at the rear of the clock for any broken wires, have you recently had a new front sprocket fitted, if so it is possible you have desturbed the speedomiter drive which is located in the sprocket cover secured by an8mm bolt check the wire conection from the drive follow the wire up you will find a plastic conector, check that it is joined corectly by pushing top and bottom together, it may well be that this unit is burned out a resistance must be found at this unit using a multimeter.also behind the case located on the front sprocket is the drive gear this is secured in the gearbox shaft with a 8mmm alun bolt check for security if the bolt is loose the drive will spin on the shaft and speed will not be recognised,

Oct 27, 2010 | Suzuki GSX-R 600 Motorcycles

1 Answer

How to install chain buffer on a 95 gsxr 750 ws


pull front sprocket gear , buffer installs behind gear

Feb 23, 2010 | 1995 Suzuki GSX-R 750 WS

1 Answer

How to change the front sprocket


remove the left faring undo the water pump mounting bolts not all the bolts around the pump just the two that hold it to the engine case pull the pump out about one inch the undo the sprocket cover and remove put the engine in gear and get somone to hold the rear brake on loosen the sprocket bolt undo the rear wheel axle nut and loosen the chain adjusters to put some slack in the chain then remove the front sprocket and fit the new one on put some lock tite on the sprocket bolt and do up tite with the bike in gear and someone holding the brake on put the water pump on and make sure it is lined up properley when you push it back in it should sit flush to the engine with an easy push.adust your chain and titen all the bolts and nuts and refit your faring.hope the was helpfull please leave feedback.

Oct 11, 2009 | 2004 Honda CBR 1000 RR Fireblade

2 Answers

05 GSXR 750 Speedometer Reads 0


I just had the same problem 2004 gsxr 750. After massive troubleshooting and time I found out it was the gauge. So I then ebayed a gauge on ebay and bought on for 290 dollars. Speedo now works. I am just off on the actual speed, need to by a speedo healer.

Sep 17, 2009 | 2005 Suzuki GSX-R 750

2 Answers

1998 gsxr 750 speedo problem


if the speedo doesn't work through a cable then it probably works on a electronic sensor.try and trace the wire from the back of the speedo to the sensor and replace the sensor.will more than likely be around the front wheel area or the gearbox.

Mar 05, 2009 | 1996 Suzuki GSX-R 750 T

1 Answer

98 gsxr 750


Make sure the cable didn't slip out of it's detent. If it isn't placed exactly where it should be, you gon't get proper tension on the clutch plate.

Jan 30, 2009 | 1998 Suzuki GSX-R 750 W

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

231 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...