Question about 2008 Tomos Se 125 F

Open Question

Tomas Nitro 150 will not start with ignition, only kick start. No running day lights and not a lot of power to signal lights

The ignition makes a clicking sound when turning ignition on.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2007 Bajaj Pulsar 150 will not start


Hi, Dharma and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the choke.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. Fuel injectors stuck open.
13. Quick disconnect check ball stuck.
14. Compression below 75 PSI.
15. A stuck-bent-burnt valve.
16. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
17. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
18. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
19. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections are loose or connected to the wrong cylinders.
20. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
21. Faulty neutral, clutch, kickstand safety switch.
22. Faulty fuel pump or fuse or relay.
23. Faulty or corroded run/stop switch.
24. Tilt sensor needs a reset.
25. Security system not disarming alarm needs a reset.
26. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Thread Pulsar 150 start problem
Pulsur 150 Bike not getting started
https://www.bcmtouring.com/imp/Pulsar_DTSi_Workshop_Manual.pdf
Shop At Bajaj Pulsar 150 Classic Bike Parts And Accessories Online Store...
Bajaj Pulsar 150 DTS User Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

May 22, 2018 | 2007 Bajaj Pulsar 150

1 Answer

Bajaj Pulsar 150 will not start when warm


Hi, Dharma and the usual suspects are:
1. Faulty ignition coil.
2. Faulty spark plug cables.
3. Faulty temperature sensor.
4. HISS light not going off.
5. Faulty starter motor.
6. Valves adjusted too tight.
7. Spark plug gap too wide.
8. Fuel has vapor lock.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
7 things you should check if your motorcycle is not starting
PULSAR DTSI 150 2003 unique problem Team BHP
Pulsar Workshop and Parts Manual Team BHP
https://www.scribd.com/doc/42303845/Pulsar-Spare-Parts-Price
https://www.bcmtouring.com/imp/pulsar-180-ug3-owners-manual.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Apr 08, 2018 | Bajaj Pulsar 150 Motorcycles

1 Answer

Diamo scooter kick starts electric starter not wiring


Hi, Anonymous and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Faulty starter button/switch.
6. Faulty jiffy stand or clutch pull in switch/sensor.
7. Security alarm needs a reset.
8. Starter control circuit, relay, or solenoid faulty.
9. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue and valuable "FREE" downloads that you will need please visit the websites below. Good luck and have nice a day.
Scooter Troubleshooting Scooter won start All about Scooters
http://www.linnbenton.edu/auto/perform/no_start.html
The Ultimate GY6 Starter Ignition Troubleshooting Tutorial http://scmotorized.com/image/data/pdf/scooter-repair-manuals/Retro-150--Parts-Catalog-V.12.07.pdf
Diamo Retro 150 2007

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Sep 24, 2013 | 2007 Diamo Retro 150

1 Answer

1989 ford f-150 no ignition when key on have radio heater fan signal lights etc. but no ignition ? vehicle will start by jumping the solenoid or by using command start


It sounds like the ignition switch (electrical) which is mounted on the column has gone bad, or you have a neutral switch that is not working. If you have a test light, test the small signal wire that pushes onto one of the pins on the solenoid. Also make sure the stater solenoid is mounted tightly, they must have a good ground to work.

Oct 31, 2010 | 1989 Ford F 150

3 Answers

Honda 150 motorcycle, it runs but no lights and


good day Sir, try to check the timing off the magnito and check the fuse i hope it will help you.

Apr 06, 2010 | 2005 Honda CG 150 Titan ESD

1 Answer

2007 Nitro will not start


asd/ignition relay shorting or possble pcm/gem failure. Depending on mileage, I would return to dealer as this is a warranty issue.

Dec 25, 2009 | 2007 Dodge Nitro R/T New Cars

1 Answer

Interior trailer lights dont work


On some of the vehicles, the ignition switch must be on to power the 12 volt lights. Try that first. I assume that you are using a 7 pin connector, otherwise the running lights can feed power to the interior lights. You can bypass this by running an inline fused wire from the battery to the wiring, but you must disconnect the switched wiring and secure it. You don't want feedback into the wiring harness. Also try http://www.etrailer.com/faq-wiring.aspx. They have a great website with lots of info.

Oct 04, 2009 | 2001 Ford F350 Super Duty SuperCab

1 Answer

1990 F-150 running


have you checked the ignition modual

Dec 19, 2008 | 1990 Ford F150

Not finding what you are looking for?
2008 Tomos Se 125 F Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tomos Experts

gavinabc123

Level 1 Expert

13 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4988 Answers

micky dee

Level 3 Expert

3015 Answers

Are you a Tomos Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...