Question about 1998 kawasaki KDX 200
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Thats not likely. What you are seeing is excess oil from you gas and oil mixture. Not sure if your still running the oil injection pump but it sounds like you have been running a very rich oil/fuel mixture.
The gearbox oil is not accessible through the crankcase. They a totally separate sealed sections of the motor. If by chance you are losing gearbox oil your bike will billow a very white disgusting smelly cloud of smoke. If that is what is happening you may have a right side crank seal blown which will allow the oil to be sucked from the gearbox into the crankcase. Hopefully this is not the problem because with your model I'm 85% certain you will have to split the cases to replace the main seal on the right side engine center case. If thats the case I'd highly recommend you replace both right and left main seals as well as main bearings.
You will need some special tools to do this job. I can tell you what you need to do the job and if you like to DIY I can tell you how to do it and what to look out for.
Best of luck.
Posted on Dec 06, 2008
ALWAYS have a fire extinguisher at hand when working on carburetors.
Remove the water trap bowl at the bottom of the petcock, (gas valve). Is there any water or trash in the bowl? Drain a cup of gas from the tank. Is there any water or trash in the cup? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ).
Drain the carburetor. There should be a screw on the lower side of the carb float bowl. Remove the screw then replace it after the fuel drains. Turn the gas back on and wait a minute for the carb to fill with gas. Install a new stock NGK spark plug and try to start the engine. If the bike doesn't start and run properly then shut off the gas and remove the carburetor from the engine.
Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the idle screw and the air screw on the outside throat of the carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two adjusters down. Only screw these in until they LIGHTLY seat. Now turn each adjuster one and one half turns outward. Before putting the slides back in the throat of the carbs, Move the clip on the jet needle one notch lower. Put the rest of the carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine. This process should get you back on the road.
Please rate this solution. Thanks!
Posted on May 05, 2009
the floats may be damaged
try to level the floats with the base of the top part of the carby and see how you go .
you may have to try a few times until you get it right .
Check your needle point too as it may be stuck as well .
Posted on Sep 27, 2009
Tips for a great answer:
Feb 22, 2016 | Motorcycles
Mar 16, 2012 | 2004 Honda CRF 250 R
Nov 07, 2010 | Suzuki RM 250 Motorcycles
Aug 04, 2010 | 1998 kawasaki KDX 200
Nov 11, 2009 | 2002 KTM SX 125
Aug 25, 2009 | 2003 Suzuki RM 250
Jul 22, 2009 | 2003 kawasaki KX 125
May 28, 2009 | 1998 kawasaki KDX 200
50 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: