Question about 1994 kawasaki VN 750 Vulcan

Open Question

When i ride my kawasaki volcan in first gear i begins to sputter and sometimes dies, it also does it when i am ridding on the freeway at around 60 mph does anyone know what i can do to fix this

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
bozcro
  • 867 Answers

SOURCE: Motor dies in first (or any ) gear.

well, if you checked the fuel system and all is clean, with new plugs , all is left to test is the ignition coil, its contacts and cables

Posted on Jul 12, 2009

Ad
  • 47 Answers

SOURCE: How to increase top end speed - 2007 Kawasaki Ninja EX250R

you can change the sprockets.If you go to a 16 tooth front sprocket. two teeth on a front sprocket is like droping 4 teeth on the rear. You could drop 2 teeth on the rear sprocket but a 43 tooth is probably harder to find. the usual choices for front are 14,15,16 tooth.
For the rear they are 44,45,46 tooth

The way to remeber gearing changes is on REAR sprocket is smaller=faster and larger=slower top end.
the FRONT is OPPOSITE to the rear smaller=slower and bigger=faster.
You may have to lengthen or shorten the chain depending whjch way you go.

Posted on Mar 21, 2010

  • 5 Answers

SOURCE: motor revs fine on my kawasaki 400 but try to ride

also check the side stand switch disconnect it

Posted on Apr 27, 2010

  • 232 Answers

SOURCE: What would cause my '03 Kawasaki 500 vulcan to

Hi ,
The thermostat may be playing up and will need to be replaced .
Bare in mind that any liquid cooled motor will need the coolant to be replaced and cooling system flushed out on a regular basis especially while riding in city as the engine is constantly in the high temperature .

Posted on Jul 15, 2010

  • 1 Answer

SOURCE: I HAVE A 2001 KAWASAKI BAYOU 300 4X4 WHAT OIL

4 stroke sae 30 advanced auto parts 8.00

Posted on Feb 27, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 Cadillac Escalade engine died and all electrical quit while on the freeway at 60 mph


Check battery connections and have battery and charging system tested.

Jan 04, 2014 | 2007 Cadillac Escalade

1 Answer

1996 honda odyssey - after warm up, at highway speed 65 mph and accellerating (up a hill etc) makes a vibration or engine missing. It gets steadily worse, happens at lower speeds and in lower gear as


If the engine is misfiring you would have a blinking check engine light and a fault code stored for the cylinder that is misfir9ing is that the case? If it was me I would replace the spark plug wires, they are cheap and most likely the problem.

Jul 10, 2017 | 1996 Honda Odyssey

1 Answer

I have a 1973 Yamaha tx650 that I turned into a bobber. Straight pipes off the engine. When I ride it, the engine begins to lose power and bogs down, and back fires around 60 mph... even with the throttle...


with black plugs it might be that there is no back pressure because of the cut off pipes. It also could be valve guides leaking oil into the cylinders.It is most likely that the carbs are not tuned to the opened exhaust

Feb 06, 2011 | 1973 Yamaha TX 650

1 Answer

19 hp kawasaki mower motor that dies after operating 45 minutes


well its back to the fule flow,,,i thing the fule lines and carb are blocked up and needs a strip down and a good clean up of all the jets and flote bole this sounds like fule shortage,,,if the engine is only just turning and you try to put it in gear so the cutters start to turn it loads the engine up and it stops!
you say pulling the choke out get it going!!!!! then its short of fule ,,,right!

Jul 15, 2010 | kawasaki Garden

1 Answer

Cluncking/grinding sound as i pull away in most gears as if there is nut or something bouncing between cogs


Stop riding the bike. The tranny could lock up at any moment > like at 60 mph in traffic. The gearbox will need to be opened upand the problem located and fixed. The fix is not going to be cheap $$$$

May 13, 2010 | 2000 kawasaki ZX-6R Ninja

1 Answer

Cavalier 2.4 intermittent engine die/won't start code p0600


Check the catalitic converter in the exaust. It may be stopped up. This can cause these symptoms.

Jan 27, 2009 | 1996 Chevrolet Cavalier

1 Answer

Speed problem


You have a carb problem. Check your piston vacume in your carbs.I had the same problem,and it was the piston vacume that had a hole in both piston.Good luck tom :D

Nov 20, 2008 | 1983 Honda GL 1100 Innerstate Gold Wing

3 Answers

Top speed


no you **** going bigger in the back is more accel, smaller is more top end. a 48-46 would put you somewhere between 80-100 mph depending on the engine but result is **** low end. If your kx is 6 spd you would benefit from going up a tooth or 2 for lowend because it has topend already.

Nov 10, 2008 | 2007 kawasaki KX 125

Not finding what you are looking for?
1994 kawasaki VN 750 Vulcan Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...