An expert who has achieved level 2 by getting 100 points
An expert that got 5 achievements.
An expert who has written 50 answers of more than 400 characters.
An expert whose answer got voted for 20 times.
Re: raddio goes off preset when you turn it off
Typically a radio of this type has two power wires. One is the main power which is switched( hot with the key on) and the other is constant supply for memory functions. If you have power on both of these wires with the key on the radio unit is most likely bad.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
If it is aftermarket, some one might not have hook the memory wire up. But most will preset, it will just be lost when you turn off the car. If it is hooked up right, after market or factory, it is an internal failure. Replace the radio.
Toyota vehicles have a fuse in the kick for the amp and sometimes there is located under the hood ... This is the switch turn on for the amp ... And 1 of the fuses is most likely the memory or constant power. B sure to check all fuses ... I do not have AllData pulled up . If the fuses are all good the amp or radio may be bad ... Or both ... Be sure to check all the fuses ... Many times I get clients that say allthe fuses are good and it is still the first thing I check ..Usually is a fuse ..Good Luck
does cigarette lighter work you most likely have a blown fuse in the memory of clock it is part of the stereo but has 2 fuses that function it, power and memory. If its in the radio/clock all presets on radio usually go out to, look for blown fuse.
Ford Code Entry Instructions
Once the unit has been turned on the display will show ' CODE - - - -'
Press preset [ 1 ] repeatedly for the first digit
Press preset [ 2 ] repeatedly for the second digit
Press preset [ 3 ] repeatedly for the third digit
Press preset [ 4 ] repeatedly for the third digit
To save the code press the [ 5 ] key to accept.
The set should now operate.
When you turn on the radio, it will say "codE" on the display. You have the 4-digit code number for your radio, to enter the first digit, press the "1" button on the radio the number of times until the first digit matches. For example, if your code is "2156" then, press radio preset button 1 two 2 times, then press radio preset button 2 one time, then radio preset button 3 five 5 times and finally preset button 4 six times. THEN if the display is correct (should show 2156 in this example), press TAPE button. You should hear a beep and the radio should be working. If you make a mistake and enter a wrong code, the display will show "Err". You have 3 tries to get this correct or the radio may be toast. These are the steps for the stock radio in my 1995 GSX and they've worked for me each time I've lost battery power. Good luck!
If it is an aftermarket radio then that means that the constant power wire is not connected. It has to be connected in order to keep the memory of the stations. If that does not work then contact me back and there might be a couple other things. I hope this works for you.
Blaupunkt Boston CC-22 Code Entry Turn on the radio, the display will show 'COD'
Press preset [ 1 ] repeatedly for the first digit followed by [ station + ] Press preset [ 2 ] repeatedly for the second digit followed by [ station + ] Press preset [ 3 ] repeatedly for the third digit followed by [ station + ] Press preset [ 4 ] repeatedly for the fourth digit followed by [ station + ]
i figured it out with help from a delphi service rep.! you need to go into the menu and reset to factory default.this will erase everything you have changed from the factory settings,but once done you can reprogram your settings and they will stay. step 1-enter menu step 2-reset factory default settings step 3-reprogram your preset stations,FM freq. colors etc. step 4-use power button on the roady to turn it off.once the roady shuts down turn it back on with the power button. step 4-now you should be able to turn the key off without erasing your presets.