Question about 2002 Yamaha FZS 600 Fazer

1 Answer

I have a FZS600 02, the front brakes seem to rubbing on brake disk, there is no travel on them, and the brake lever is set on 5. please help

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 137 Answers

Hi m8, all the setting on the lever will do is adjust to your style of riding ,, not adjust the pads ,,sounds like the pistons on the calipers are not releasing wen the pressure is off, ,,ie brake pads are not goin back ,,if u r a every day rider ,,the salty conditions will cause seize ups,,best thing is wipp a caliper off the wheel,, dont touch the brake lines,, just undo the two caliper bolts, then undo the two screws onthe master cylinder,,reservoir,,lift off the cap, u will need some copper grease,and a small paint brush,, take the pads out, and smear some copper grease round the pistons, then prize them back in a bit,, dont push them in to far ,,just enuff, till grease to do its job,,by undoing the reservoir the air that may get pushed will be able to escape,,replace pads, and bolts, cheers

Posted on Jan 23, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need diagram showing how to put rear brake shoes on 1994 escort


Adjustment: 1) Start the engine and shift to Reverse. With the vehicle moving backwards, firmly depress the brake pedal several times to seat the shoes in the brake drum. Turn engine off. 2) Remove the console trim surrounding the parking brake lever. This isn't really necessary if you have a deep socket and extension. 3) Pull up on brake lever until the seventh notch is engaged, just listen and count the clicks. 4) If it is out of adjustment and you can't get the seven clicks, turn the adjusting nut located on the drivers side next to the lever. 5) Release the lever, block the front wheels, raise the rear end. Best to put on jackstands. 6) With car in neutral and brake lever released, rotate the rear wheels. The wheels should turn freely, but a slight drag is acceptable. 7) If the lever travels too far or the parking brake fails to hold the vehicle on a hill, tighten the adjusting nut a little more and recheck,

Jun 28, 2014 | 1994 Ford Escort

1 Answer

Rubbing noise


sound like worn out brake pads worn down to the metal rubbing damaging brake rotors

Dec 26, 2013 | Cars & Trucks

1 Answer

To much travel in front brake lever


Hi Anonymous, please be aware that this question has already been asked and answered. Thank you

Mar 19, 2013 | 2002 Harley Davidson XL 1200 C Sportster...

1 Answer

Did complete brake job on 1997 Ford Escort wagon no abs rear shoes, drums, lines, wheel cylinders,even changed the block at the rear were the lines go in & out of. Front lines hoses pads, caliplers...


is brake pedal hard to push down without engine running ,if so proceed to step two and thats to start engine and then push on brake and if pedal softer to push then the servo is working ,now if excessive pedal travel with engine running then remove the rear drums ,make sure the outside lip is cleaned out and then adjust the brake shoes manually till they rub when you turn the drum ,this will cure it but remember that it has to bed in of course new pads brake disks ,new shoes and drums it has to bed in so give it a chance .

Aug 24, 2011 | 1997 Ford Escort

1 Answer

Derbi Terra 125 problem with the front brake: brake lever is very hard travels only few mm when squeezed (there's no regulation on lever) brakes are too sharp and sometimes brake pads dont free the...


Hello, Never dealt with motorcycles, still if you are sure that there is no air in the brake liquid, check whether the braking disk/pads are not hooked or (irregularly) worn-out. If this is not the case, replace the braking mechanism (the cylinder which pushes the pads), if too expensive, clean the old one and reassemble with new rubber parts. Please let me know whether I was able to assist.

Aug 08, 2011 | 2011 Derbi Terra 125

1 Answer

HUFFY TUNDRA 18 SPEED. WOULD LIKE TO TIGHTEN BRAKES. BOTH BRAKES APPEAR NOT TO STOP MY MOMENTUM. THE BRAKES 2 WEEKS AGO WERE TUNED UP AT A PROFESSIONAL BIKE SHOP AND WERE WORKING PERFECTLY BUT NOW THEY...


adjusting the brakes will only improve their performance if when you squeeze the levers they bottom out against the handle-bars - that is, you run out of brake mechanism travel before you run out of hand strength. If that is what is happening, then you should take it back to the bike shop as they didn't get it right. On the other hand, if you are able to squeeze plenty tight without running out of travel, but the brakes aren't performing well anyway, then it seems likely that you have got something dirty, wet or slippery on the wheel rims (where the brake pads rub). If that is the case, clean the rims with something like windex. If you use Fantastic, be sure to rinse and dry. Good luck, Al K

Jul 04, 2011 | Cycling

1 Answer

Front brake lever has little to no play... leaving front brake with too quick of a respone for stopping.


Technically, there is no adjustment for the brake lever,the effort required or the amont of "travel". You have a very responsive lever and if someone unqualified attempts to "fix" this phenomenom, I suspect that you'll be setting yourself up for trouble. Personally, I'd find an empty parking lot and practice, practice, practice as the front brake is responsible for 70% of all effective braking.

Sep 30, 2010 | 2005 Harley Davidson XL 1200 C Sportster...

1 Answer

How to adjust front brake lever on '06 hd road king?


This is by design. When you have new pads on the bike and a rotor within limits the lever has very limited travel before engaging.
As these parts wear the position of which the lever engages changes. Unless you know that at the last brake pad change the caliper was "centered" this could account for the travel and will result in premature wear on the components.

JP

Sep 22, 2009 | 2003 Harley Davidson FLHR Road king

1 Answer

I had new front pads fitted to my ZX10r 06-07 when i pulled on the brake lever it was nice and sharp + the lever would only come in a short distance to the throttle grip..2 weeks on the brake lever nearly...


Possibly 2 problems m8.
If the brake-lever travel has increased then it either wasn't bled up properly or it's allowing air past the seals in the master-cylinder.
Try tying the lever back to the bar overnight to bring any air in the system up to the top (resevoir) and see if the brakes stay good, if not they'll need bleeding again.
Check for any leaks around all the banjo connections, up at the bars and down at the calipers, plus have a close inspection of the master-cylinder piston area for leaks.
The juddering might be down to a warped disc or two, get the front wheel off the ground and spin the wheel to check for this visually or with a stick and pointer.

Jun 17, 2009 | kawasaki ZX-10R Motorcycles

2 Answers

Rear brakes don't work on 1996 goldwing


Yes the rear pedal operates the front RH disk as well.
When you bleed the brake do the front RH disk calliper first then the rear calliper.
Check that the pads are not beyond useful life and the not stuck.

May 31, 2009 | 1996 Honda GL 1500 SE Gold Wing

Not finding what you are looking for?
2002 Yamaha FZS 600 Fazer Logo

273 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

D. E. Hev

Level 3 Expert

1132 Answers

puggy666

Level 1 Expert

47 Answers

dhnguyen

Level 2 Expert

233 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...