Question about 2004 Yamaha YZF-R6

1 Answer

Clutch slips and won't engage enough for it to go

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

  • Yamaha Expert
  • 473 Answers

Time for a new clutch assuming you let all the adjustment out.

Posted on Oct 21, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What allows clutch to slip so much to not move car.


-Possibly time to replace new clutch.

Good luck


mai

Nov 10, 2014 | 1990 Toyota Camry

1 Answer

Blades won'e engage


Your belt may be on wrong or slipping.

May 23, 2013 | Craftsman Garden

1 Answer

HD Dyna 2010 Superglide won't start


Hi Clements_car, and the usual suspects are:
1.Ignition/Light Key Switch not in IGNITION position.
2.Engine Stop switch in the OFF position.
3.Discharged battery, loose or corroded connections check negative cable at both ends. (solenoid chatters).
4. Bank Angle Sensor tripped and Ignition/Light Key Switch not cycled to Off and then back to on.
5. Starter control circuit, relay or solenoid faulty.
6. Electric starter shaft pinion gear not engaging or over-running clutch slipping.
7. Security alarm not disarming
For a prime suspect please visit website below and good Luck.
Harley Diagnostic Codes 04 to Present
Set Change Override Transport Harley Security Alarm PIN Code No Key Fob...

Mar 25, 2013 | 2010 Harley Davidson FXDC Dyna Super Glide...

1 Answer

I have a 1999 Gilera Runner 180FXR, New bat 12V 9 amps. Starter turns and spins pinion gear but won't engage starter ring. If it does it turns ver slow or won't turn engine over. In manual it


Yep, not enough amps to engage the starter clutch, and when ti does engage, not enough amps to turn the engine. You need a 12 amp battery.

Nov 17, 2012 | Motorcycles

2 Answers

Vt aircon compressor wont engage


check the freon, if there isn't enough it won't engage, could also be the low pressure switch or a fuse.

Sep 05, 2012 | Holden Cars & Trucks

1 Answer

Clutch not engaging


Does the clutch not engage( ie it slips & wont pull away) or does it not dis-engage (ie always in gear)
Was the clutch dismantled or disturbed when top-end was replaced
Is clutch hydraulic or not

Jan 31, 2012 | 2005 Suzuki RM 85

2 Answers

Clutch went to the floor


lost preasure at clutch check fluid level first.

Aug 21, 2011 | 2004 Pontiac Sunfire

2 Answers

Ac won't get cold anymore power to compressor but won't click on clutch won't engage possible problems are compressor or evaporator what do you think?


Has the Freon been checked with a gauge to see if there is enough Freon to allow the system to work. Low or no Freon will not allow the compressor to engage. The low pressure switch is most likely activated due to low freon, and will cause this condition.

Aug 19, 2011 | 2001 Jeep Grand Cherokee

1 Answer

The clutch in my 88 prelude is slipping so bad i can barely accelerate and its so bad i cant go up any hills. What is the problem & is there a temporary fix?


I think you know enough, that there is no fix other than
removing the transaxle & doing a complete clutch service

You shouldn't have driven it at all for some time now
& you knew that as well,but it all has to come apart
& everything replaced, so it really didn't matter

No some day, when you own an automatic,you stop driving
it as soon as you can get it home or to a shop, or you
will ruin it in a matter of less than an hour,once they slip

You will need the flywheel machined or replaced
A new Clutch Pressure Plate
A New Clutch Disc
New Clutch Slave Cylinder & Throw out Brg

As I said trans has to come out first

Figure you may go as high as $1000.00

Aug 04, 2011 | 1991 Honda Prelude

Not finding what you are looking for?
2004 Yamaha YZF-R6 Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...