Question about 2002 Kymco Stryker 125

1 Answer

Clutch when my bike is driving the clutch is slipping. what would be wrong? and could i repair my bike myself? it is a Kymco Striker 125cc.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 29 Answers

Ok there is two solutions to this prob to consider first try the clutch cable adjustment. If that does nothing try The clutch springs inside the case. If there are wear marks on the clutch basket then you need to completely replace the clutch all together. let me know how you make out

Posted on Feb 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pit bike starts, idle and revs good. But when I put it in any gear it cuts out. No electric starter, battery or kick stand switch!!? Help please?


does this happen as soon as you put it into gear or does it do it when you let the clutch out,as this sounds like the clutch plates are stuck together,you need to drain the oil then take the clutch cable off ,then take the clutch cover off remove the bolts and springs from the clucth basket make sure you do this evenly,then you take the clutch plates out if they all come out together then there locked up pry them apart and see if there is blueing of the steel plates and check the fibre plate for wear or cracks ,if the plates are bluing you may need to renew all of the steel and friction as this may have been caused by slipping the clutch or not having the clutch adjusted right and you may need a different type of oil that is suited to wet clutches.hopefully it could be just a matter of it sitting too long without being used.cheers hopes this helps

Sep 18, 2013 | Pit Bike 125cc 4 Stroke Dirt Bike

2 Answers

Not sure of the year but my Super 9 that I bought new a year ago seems to slip a little and a getting a vibration may be from the belt. A Kymco dealer on the phone thinks that the mfg. puts too much grease...


Hi,
Looks like your torque pulley, located at the rear that drives the axle/wheel has the problem.
The friction material or clutch is already worn out and started to slide. Any motor bike tech can replace it with similar part or better buy an aftermarket racing clutch w/ spring that is much better and stronger than the stock parts.
Hope that helps you out.
Thanks for asking FixYa!

Aug 06, 2011 | 2008 Kymco Super 9 LC

1 Answer

2004 FZS 1000 Clutch slipping problem.


Sounds like the friction material bonded on the friction plate are coming off, time to do a clutch job.

May 25, 2010 | 2004 Yamaha FZS 1000 Fazer

1 Answer

Slipping clutch


The hydraulic clutch wont cause slip, unless the slave cylnder piston is stuck. The hydraulic part just replaces the cable
If its a wet clutch make sure you are using motorcycle oil, some car oils can cause clutch slip, If your using a synthetic oil, you might try a mineral oil to see it it makes a difference, 600 miles is not enough to wear the plates

Apr 14, 2010 | 2003 Moto Guzzi Griso

1 Answer

CLUTCH IS SLIPPING. THE BIKE HAS 14k MILES AND


buy a clutch kit should have clutch plates and friction plates make sure it has the right oil as well wrong oil will burn the clutch plates up

Jun 23, 2009 | 2004 BMW R 1150 R Rockster

1 Answer

Atomic 125cc pit bike oil screen?


the oil filter is above the oil plug, you have to remove the clutch cover etc.. its just a piece of fine wire mesh

Apr 22, 2009 | RTO Pit Bikes

1 Answer

Clutch that is slipping on a Honda CBX750F1 mod 1986


This is not a known problem on this type of bike. The clutch was designed to do the job without slipping. This is a repair you can do yourself if you have the tools.

Assuming no updates, you original clutch plates are 25 years old. I would suggest you get a new set of Barnett clutch plates. The dealer can get them for you and install as well.

Apr 14, 2009 | 1984 Honda CBX 750 F

1 Answer

Hard to select neutral


Difficulty in selecting neutral is most likely due to clutch drag. Does the bike jump forwards when you select first gear? This could be due to dry or wrongly adjusted clutch cable. Another though less likely cause could be weak clutch springs or a worn clutch basket. Aim for about 5mm free play at clutch lever.

Apr 13, 2009 | 2004 Suzuki VL 125 Intruder LC

1 Answer

Require Kymco B&W 125cc workshop manual


google your kymco model and cc SERVICE MANUAL.i found mine in pdf.it was chinese and english on the same page.

Mar 17, 2009 | 2002 Kymco Stryker 125

Not finding what you are looking for?
2002 Kymco Stryker 125 Logo

Related Topics:

425 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kymco Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...