Question about Motorcycles

1 Answer

How to reset belt light

Will not run over quarter throttle, speedometer reads that its moving when its not

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 11 Answers

Remove and refit hopefully in the correct position.

Posted on Jan 10, 2013


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 32 Answers

SOURCE: hi my bike starts and

Try changing the spark plug first and clean the air filter.

Posted on Sep 24, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

The speedometer not working right why? and the left front seat want move why how do i fix it what is causing it not to move? i can hear a sound when i press the seat switch.

A few possible issues that may cause your speedometer to not work are a bad speed sensor / gear. Could be an internal gear inside the transmission, not as common of a problem.

What type of sound do you hear when trying to move the driver seat ? Is it a clicking or the motor seat motor running ? This can help determine what may be your problem.

Jul 24, 2017 | Lincoln Cars & Trucks

1 Answer

2005 Harley Davidson road glide When I throttle up the check engine light comes on When I hold a steady throttle the check engine light goes off I have replaced the fuel filter fuel hoses with factory...

Pull any error codes.


1 - Turn the ignition switch to off & run/stop switch is to run .
2 - Push odometer reset button in & HOLD .
3 - Turn the ignition switch on and then release odometer reset button. The background lighting should illuminate & the speedometer needle should sweep it's full range & indicator lamps ( battery , security , low fuel , check engine and cruise ) should illuminate . The word "DIAG" should then appear .
4 - Push the odometer reset button once and you will see the selection menu "PSSPtb" with the first P flashing .
5 - Each letter represents a area of the diagnostics module. The module that is flashing is the one you are going to check . To move from one letter to the next you must push the odometer reset button one time . ( from P to S to SP to t to b and back to P , ect ect )
SP = speedometer
t = tachometer
b = ABS codes
6 - To get the DTC code in a area of diagnostics you should PUSH & HOLD the odometer reset button in for 5 seconds and the release . If there are any DTC's the code will be displayed or the word " none " will appear if there are no DTC's . Push the odometer reset button again to view any additional codes if they exist .
7 - Record the codes .
8 - If DTC's are NOT to be cleared , press and release the odometer reset button . Part #of module will be displayed .
9 - If DTC's are to be cleared for that module , PRESS & HOLD the odometer reset button until " clear " is displayed .
10 - Press and release the odometer reset button to continue to the next module .
11 - Turn the ignition switch off to exit the diagnostic mode.

Once you have any codes, look them up, or post here (I have a manual that translates the codes), to find out what they mean.

Jan 01, 2014 | Motorcycles

1 Answer

06 harley flhtcui, check engine light comes on when i hit 65mph, once I let off the throttle and get under 65mph it turns off. Any ideas?

The best way to check is to pull any error codes (DTCs) and see what the computer says is going on.

Turn the Ignition switch to the OFF position.
Set the Run/Stop switch to the Run position.
Push in the odometer reset button and hold.
Turn on the ignition switch and release the odometer reset button. The process has been completed correctly when the speedometer needle sweeps across the speedometer and all indicator lamps illuminate. The speedometer will also display "DIAG."
Press the odometer reset button once. "PSSPt" will display on the speedometer. Each letter signifies an area of the diagnostics testing, with the current selection flashing. Push the odometer reset button to scroll through the components for testing.
Press and hold the odometer reset button for 5 seconds, then release. Any codes stored will be displayed on the speedometer. If no codes are stored, the speedometer will display "NONE."
Press the odometer reset button again to view additional codes, if any.
Record the codes and refer to your service manual for possible faults or conditions.
Turn off the Ignition switch to exit the diagnostics testing.

Once you pull the codes, post them here and myself, or someone else, can look them up and tell you what they mean.

Nov 25, 2013 | Harley Davidson FLHTCUI Electra Glide...

1 Answer

Engine revving

sounds like the stop pin has been moved check on the throttle there is a little stop screw see if it is coated in muck and the part that the throttle arm hits the pin. someone may have moved its setting before hand. and now the problem has been fixed with a new timing belt the timing is right and engine is running smooth. if engine is pinking the timing belt is still not set properly and this is the reason for high revving. timing is to advanced. and needs reseting.

May 10, 2013 | Gates 2003 Ford Focus Belt Tensioner

1 Answer

Gas light stays on and it reads a quarter tank

Dear Sir>
Please see the schematic attached, proceed with logic system for troubleshooting and fix it. Look for loose connection, corrosion, dirty, dust, vibration, burn or break wires, defective relais or pump.
God bless you

May 24, 2012 | 2000 Kia Sportage

1 Answer

The belt slides to one side (the same side) always when we start to walk. It is a new belt and deck. Afraid it will wear out the belt as it starts to rub against the edges. Thanks

you need to tighten the w/belt. the side that the belt goes to tighten 3 quarter turns. now on the other side loosen 2 quarter turns. turn on the the belt on 3or 4 setting the belt should start moving over when it get to where you want it tighten the sid e you first loosen 2 quarter turn. then run it at higher speed to see if it stays its trial and error remember rightie tightie leftty loosie. in the end you want equal tension with the rollers bolts ps good tension is 2 -3 inches up when lifting up the sides of the w/belt

Mar 17, 2011 | Life Fitness T3 Treadmill with Advanced...

2 Answers

I have a 2000 model Prado with a digital speedometer counter. the T-Belt light has come on at 120,000 Kms and i have just changed the timing belt. I need to know how to reset the warning light myself if...

i have exactly the same model and same problem at 100,000 km however i read the forum advice but my one neither has the grommet on the front neither a screw to re-locate to reset so the only way was to remove the bulb instead

Sep 21, 2010 | Toyota Land Cruiser Cars & Trucks

1 Answer

Engine light comes on when i open up throttle

I would start by retrieving the diagnostic trouble codes. To do this, with the run switch on the right grip set to run, hold the odometer reset button in and turn on the ignition to run then release the odometer reset button. Background lighting should illuminate, the speedometer needle should sweep its full range of motion and the indicator lamps should illuminate. After that the readout on the odometer should indicate any trouble codes. If there are any trouble codes I have a list of them to direct you to the problem. If you want to clear the codes, press the speedometer reset switch for more than 5 seconds when the DTC is displayed.

Apr 07, 2009 | 2008 Harley Davidson FLHX Street Glide

1 Answer

2003 chrysler town & country speedometer stuck

sit in the drivers seat close the door. with the key off hold the trip odometer button in then while holding the button in turn the key on. if done correctly this will put the MIC (mechanical instrument cluster) into a self test. if the speedometer does not move like the rest of the gauges during this test the MIC must be replaced. if the speedometer does move it is likely your problem will be fixed, however, if the speedometer does move but it does not start working properly then further diagnostic will be needed.

Mar 19, 2009 | 2003 Chrysler Town & Country

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4749 Answers


Level 3 Expert

78267 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides