Question about 2010 kawasaki Z750

Open Question

How to remove the catalytic converter on a z750 kawasaki 2010 mdel

Want to remove the catalytic converter

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
DickCanFixIt
  • 948 Answers

SOURCE: kawasaki z750 abs. Vacuum (pression) in fuel tank

If you're building up vacuum or pressure in the fuel tank, your vent line is pinched or plugged. It is a rubber hose that comes off the fuel tank, usually runs down the right side and discharges vented air out the bottom somewhere.

Posted on Jun 25, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the 02 Oxygen Sensor before the cadalic converter on a 2006 Hyundai Santa Fe


Usually these are located on the exhaust manifold or just below the exhaust manifold and you should be able to see it in the engine bay. On V6 engines there will be one sensor on each of the 2 exhaust banks.
You will probably need to remove the engine cover to see the sensors on your exhaust.

If someone told you to replace these because you got a particular fault code I would be wary. A decent scan tool and basic diagnostics can show if the 02 sensor is working or not. Some faults often blamed on an 02 sensor are not due to faulty sensors.

Jan 09, 2016 | 2006 Hyundai Santa Fe

2 Answers

Catalytic converter is missing. The only thing in the housing is a metal ring. There are no signs of theft.


Catalytic Converter? - Nissan Titan Forum

www.titantalk.com > ... > Titan Performance Modifications
May 31, 2010 - 15 posts - ‎10 authors 2004-2006 4wd = 4 cats, you can remove (or gut) the two rear cats with no issues...just..... I have a 06 2wd I am about to do the exhaust. Hello Titan Owners! NEED HELP . Catalytic Converters ...
15 posts
Apr 25, 2014
Code P0420, Catalytic converters and exhaust system
9 posts
Jul 31, 2012
catalytic Converter going / Calif Emissions
12 posts
May 2, 2011
Catalytic Converter(s) bad
15 posts
Nov 20, 2009
More results from www.titantalk.com

Oct 29, 2015 | 2004 Nissan Titan

1 Answer

I have ordered an a16 race can for my kawasaki z750 07. I have taken original can off but it has two cables attached to it which go under seat to a box what is this and can the new race can be fitted...


This is an exhaust power valve...remove the cables from the servo box under the seat. Keep the servo box in place as removing it will cause a Fi warning light.

May 05, 2014 | 2007 kawasaki Z750

2 Answers

I have an 1998 Chevy Blazer and need to change the catalytic converter, are the flange bolts welded and can i cut them


Catalytic Converter Removal & Installation 2.2L Engine To Remove:
Catalytic converter 2.2L engine gm-03-22-734.gif

  1. Raise and safely support the vehicle.
  2. Disconnect the heated oxygen sensor (HO2S) electrical connector.
  3. Remove the exhaust manifold pipe flange mounting nuts from the catalytic converter.
  4. Remove the catalytic converter flange mounting nuts from the muffler.
  5. Remove the catalytic converter from the muffler.
  6. Remove the catalytic converter from the rear hanger bracket insulator.
  7. Remove the catalytic converter.
  8. Remove the (HO2S) from the catalytic converter.
To Install:
  1. Install the (HO2S) to the catalytic converter.
  2. Install a new gasket and the catalytic converter to the muffler.
  3. Install catalytic converter to the catalytic converter hanger.
  4. Install the catalytic converter flange mounting nuts to the muffler flange.
    • Tighten to 26 ft lbs (35 Nm).
  5. Install the catalytic converter flange mounting nuts to the exhaust manifold pipe flange.
    • Tighten to 26 ft lbs (35 Nm).
  6. Connect the heated oxygen sensor (HO2S) electrical connector.
  7. Lower the vehicle.
------ Catalytic Converter Removal & Installation 4.3L Engine To Remove:
  1. Raise and safely support the vehicle.
  2. Raise and support the transmission.
  3. Remove the transmission support
  4. Disconnect the left and right pre-converter heated oxygen sensor (HO2S) electrical connector.
  5. Disconnect the post-converter (HO2S) connector. Muffler flange and gasket gm-03-43-731.gif

  6. Remove the catalytic converter flange mounting nuts from the muffler.
  7. Remove the catalytic converter from the muffler.
  8. Remove the exhaust manifold flange mounting nuts from the catalytic converter. Catalytic converter 4.3L engine gm-03-43-735.gif

  9. Remove the catalytic converter from the support bracket insulator.
  10. Remove the catalytic converter and gaskets.
  11. Remove the heated oxygen sensor.
To Install:
  1. Install the heated oxygen sensors as needed.
  2. Install a new gasket and the Install the catalytic converter to the support bracket insulator.
  3. Install the catalytic converter to the exhaust manifold flange. Install the mounting nuts.
    • Tighten to 39 ft lbs (53 Nm).
  4. Using a new flange gasket, install the catalytic converter to the muffler. Install the mounting nuts.
    • Tighten to 30 ft lbs (40 Nm).
  5. Connect the left and right pre-converter heated oxygen sensor (HO2S) electrical connectors.
  6. Connect the post-converter (HO2S) electrical connector.
  7. Install the transmission support.
  8. Lower the transmission.
  9. Lower the vehicle.
prev.gif next.gif ---
It looks like you can cut them and replace them with new bolts and nuts.prev.gif next.gif

Sep 05, 2010 | 1998 Chevrolet Blazer

2 Answers

Kawasaki z750 abs. Vacuum (pression) in fuel tank


If you're building up vacuum or pressure in the fuel tank, your vent line is pinched or plugged. It is a rubber hose that comes off the fuel tank, usually runs down the right side and discharges vented air out the bottom somewhere.

Jun 25, 2009 | 2008 kawasaki Z750 Abs

1 Answer

DO I USE LEADED OR UNLEADED PETROL.


Unleaded. Leaded petrol will damage your catalytic converter. If you remove the converter (or just burn it out without plugging it) you can safely use either one.

Jan 26, 2009 | 1995 kawasaki ZZR 1100

Not finding what you are looking for?
2010 kawasaki Z750 Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...