Question about Suzuki Motorcycles

Open Question

How to install hid bulb on a suzuki skydrive 125

Posted by Anonymous on


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to install HID to honda xrm 125

Did you buy a HID bulb or did you buy the kit with the ballast etc? Usually an HID lamp will come with a ballast and wiring loom which is per fitted with relays etc. you would normally plug this loom into the headlight socket of your bike's wiring and then tidy the ballast etc behind the fairing and replacing your bulb with the HID lamp. If you don't have the loom and ballast they're pretty easy to come by on the auction sites.

Jul 14, 2014 | GAS EC 125 Motorcycles

1 Answer

I installed raptor hid lights on my 2006 ford f250. It called for a H13 hi/low bulb..... I purchased the kit from ddm tuning.... The installation when good except now I have no low beams..... Can someone...

interesting, make sure you have all the wiring appropriate and SECURE. otherwise it will not work. did the hid kit come with a relay harness? if you can send a pics of your set-up I will gladly assist you with your problem. I install hids as a job. when installing hids your not supposed to make any contact with the bulb directly against your skin, because the oils on your skin will damage the lens and less life of the bulb.

Jun 12, 2011 | Ford F-250 Super Duty Cars & Trucks

1 Answer

I installed a High beam hid kit and read online that they needed a resistor in that year to trick the computer. after installing the kit and the resistors to the high beams pos and neg it still flashes...

I don't know why you would install resistors inline for an HID kit, they should be 'plug and play'-you plug the connector for your halogen lights into the ballast input for the HID kit, then plug in the HID bulb harness/ bulb to the ballast output, install the bulb into the housing-done. Some people have installed relays to the lights because when the HID's 'light off' the use a lot of power until the bulbs warm up, then they actually consume less than a halogen bulb (usually 35 watts HID to 55 or more halogen). I have HID's in a number of cars and don't have relays hooked up on any, just 'plug and play' and I have no issues whatsoever.

Apr 03, 2011 | Dodge Ram Pickup 1500 Cars & Trucks

1 Answer

How do I replace the headlight bulbs on my 2007 expedition?

SECTION 417-01: Exterior Lighting 2007 Expedition/Navigator Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 08/10/2006 Headlamp Bulb adobe.gif Printable View (255 KB) Expedition Headlampn0057191.gif
Item Part Number Description 1 13006/13005 Headlamp assembly (LH/RH) 2 13N021 Headlamp bulb

Navigator High Intensity Discharge (HID) Headlamp Bulbn0057192.gif
Item Part Number Description 1 13N019 HID bulb access cover 2 — HID bulb screws (2 required) (part of 13A006) 3 13N021 HID bulb 4 13A006 HID bulb electrical connector and harness Removal and Installation
ani_caut.gif WARNING: The headlamp bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope. Failure to follow these instructions may result in personal injury.
NOTE: The headlamp bulb should not be removed from the headlamp until just before a new bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamp with the bulb removed from the headlamp.
NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
All vehicles
  1. Remove the headlamp assembly. For additional information, refer to Headlamp Assembly in this section.
  1. Rotate the headlamp bulb approximately 1/8 turn counterclockwise and remove the bulb from the headlamp assembly.
  1. Remove the HID bulb access cover.
  1. Remove the 2 screws and the HID bulb.
    • Disconnect the electrical connector.
All vehicles
  1. To install, reverse the removal procedure.


Apr 04, 2010 | 2007 Ford Expedition Eddie Bauer EL

3 Answers

Scooter HID headlamp leading to power loss

Cutting the wire will do. My Mio also have a HID any that's what we did (cutting one wire). But you can also try alternative like installing a fast charger. So you can charge up your battery fast as you use your HID.

No problems encountered with my HID using the cutting methode.

Sep 30, 2009 | 2006 Yamaha DT 125 RE

1 Answer

How do i replace the headlight bulbs for a Suzuki TL1000s. Replacing with HID bulbs...bulb dont seem to just turn and pull-out real easily.

they usually have a metal clip that holds them into the socket, be careful not to pull or bend it when removing bulb otherwise the new bulb will not fit tightly in the socket

Mar 29, 2009 | 1992 Suzuki GSX 1100 GN

3 Answers

HID fog light

check your connections to the relay, sounds like something is breaking down under load

Feb 18, 2009 | 2005 Chevrolet Silverado

1 Answer

HID headlights for esteem

There are retrofit kits for your car, but they're expensive. If you're needing better headlights I would look for a aftermarket high wattage halogen bulb. If you just want the cool look then Sylvania Silverstar bulbs are the closest low cost alternative. They're not the same as HID but they're close at a fraction of the cost. As far as HID in India, your best bet is looking on the Internet. Most HID kits that would fit your car are 200 to 400 dollars US. Good luck and don't forget to vote

Jan 26, 2009 | 2001 Suzuki Esteem

2 Answers

HID headlight

Most likely the HID transformer is not producing the correct voltage to properly charge the HID bulb. 12 volts goes into the transformer, but a lot more comes out. The HID needs a lot of volts to run, hence the need for the abovementioned transformer. But, the transformers are REALLY expensive.

Sep 18, 2008 | 2004 Toyota Sienna

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

252 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts


Level 3 Expert

76846 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers


Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides