1994 Chevrolet S-10 Logo
Anonymous Posted on Jan 07, 2013

Right blinker works but left dont an dash lights dont work

I have checked wiring an took dash gauge out an cleaned but still dont work. right blinker clicks when on but left dont. i cant find out whats wrong with it . It jut quit working all of a sudden please help

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

  • Contributor 1 Answer
  • Posted on Jan 24, 2013
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

New Friend:

An expert that has 1 follower.

Joined: Jan 24, 2013
Answers
1
Questions
0
Helped
178
Points
1

5 Related Answers

Anonymous

  • 2 Answers
  • Posted on Sep 05, 2008

SOURCE: turn signals and flashers

Hello I had the same problem on my 04 monte. After changing bulbs ,checking wires etc. I finally took it to the dealer and they found out it was the hazard switch. After swapping it with a new one all lights, dash etc started working again and have not had another problem

Ad

Anonymous

  • 12 Answers
  • Posted on Feb 16, 2009

SOURCE: My chevy z71 96 running lights work, but not right brake/blinker

check for a short it could be anywhere in the line

Anonymous

  • 59 Answers
  • Posted on Mar 15, 2009

SOURCE: turn signals and back up lights dont work.

Test the circuit board wires on the back side of your taillights where the bulbs go in to see if power is going there with the blinker on, if yes replace the circuit board (quite common with these trucks). If there is no power back there check your flasher relays for each turn signal, assuming they dont click off and on when you tip the turn lever. if all else fails, head for the multifunction switch behind your steering wheel inside the column that your turn signal/wiper/cruise control lever is connected to.

Anonymous

  • 41 Answers
  • Posted on May 08, 2009

SOURCE: Blinkers stay solid and dont flash, Hazards work fine.

CHECK GROUND ON TAIL LIGHT HOUSING.

seanpwright

Sean Wright

  • 2045 Answers
  • Posted on Sep 15, 2009

SOURCE: I am attaching tow lights to my Chevy Colorado,

You need an adapter to make them work properly...

Check this it out it will help alot...

http://www.coloradofans.com/forums/viewtopic.php?f=1&p=815675

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/sean_54c3a3dc48a7773c

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

Cant resolve a blinker issue, Tried the easy stuff.

The signal wire going to the right front has a splice for the dash indicator, a wire branching off from the turn wire and going to the dash. It sounds like that right signal wire is broken or lost a connection before it splices off to the dash, so the problem sounds like it is under the dash, either coming out of the turn signal switch to the flasher or from the flasher to that splice. You may need a multi-meter to check voltages on that wire at various places under the dash. Ascertain which color wire you need to concentrate on. Check for voltage on it with key on and right blinker on-voltmeter will spike to battery voltage, then fall to zero as the flasher breaks voltage continuously, if checked after the flasher. If checked when leaving the turn switch, it should be a continuous signal on that wire. Think you better find a wiring diagram to find the right wire to check. Good luck.
3helpful
1answer

Blinkers don't work: When I use my blinkers to

The right blinker issue sounds like you have one bulb out either front or rear check them both. The left blinker issue sounds like either bulbs(both out) or fuse, or worst case blinker switch has gone bad on left turn only so not picking up the signal.
1helpful
2answers

My left blinker and brake light dont work, i got a new blinker bulb and it still doesnt work

Check your fuses in the engine bay or under the dash. some vehicles have separate fuses for the left and right side of vehicle.
0helpful
1answer

94 dodge dakota electrical diagram,electric brake hookup.there is 6 wires off the brake switch witch one do I hoke the switching wire from the syncronizer to?

in my 94 dodge dakota when i turn my lights on sometimes all extior lights work and dash one dont and when i turn my blinkers on all my gauges bounce with the blinkers its weirdd
0helpful
1answer

Brake Lights and Hazard still dont work

TEST FRONT RIGHT BLINKER CIRCUIT AND REPLACE THE BULB,,WITH PROPER BULB...A DOUBLE CIRCUIT BULB IN A SINGLE SOCKET WILL DO THAT ALSO A SINGLE SOCKET BULB IN A DOUBLE SOCKET HOLDER....CHECK LEFT SIDE BULB FOR ACURANCY
1helpful
4answers

Blinkers wont turn on its not the bulbs or fuses 01 tahoe

Did you replace the hazard/flasher/blinker relays?- they are in the fuse block usually.

This is weird, but try this: Turn on your hazard lamps and turn your steering wheel all the way left and all the way right.
Then turn on your left blinker and hold the blinker on while you turn all the way left, then right. It will click and try to turn it off but keep it held down and turned on. Then do the right blinker the same way.
I have had this problem with every GM I've ever had, something about the detent-return and the blinker relays getting reset. I'm not sure why it works, but if your flasher relays are good and your fuses,bulbs and wires are good then this is probably what will fix ya. I've had this happen often enough that I always do this first. My GM vehicles were/are all 60s to 90s models- old school, but try this before you do anything else with it it's free and only takes about 15 seconds to do. Sometimes I have to do it more than once, but eventually the detents reset and they work. Viola!
Good luck and please rate this solution if it fixes ya!
0helpful
2answers

Fuel and Temp Gauge go on and off intermitently

faulty wiring for the lights, and blinkers....

broken gears for the fuel and temp gauge...

just get rid of the damn car, get a Civic of the same year.

I was given a 323 once, unsiezed the rear brakes (the idiot left the thing parked with the e-brake on all winter), then sold it for beer money.
0helpful
1answer

1987 Pulsar Electrical

Well first thing i would check would be the circuit plug connector at back of instrument panel is it full plugged in? if so check connectors that you did remove before making sure they are also fully and correctly plugged together
0helpful
1answer

Turn signals and flashers

Hello I had the same problem on my 04 monte. After changing bulbs ,checking wires etc. I finally took it to the dealer and they found out it was the hazard switch. After swapping it with a new one all lights, dash etc started working again and have not had another problem
Not finding what you are looking for?

188 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...