Question about 2003 Harley Davidson FLHTCUI Electra Glide Ultra Classic
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Drain the fuel either by siphening or removing the cross over tube at the front of the tank and letting it drain that way or just block off those cross over lines and leave the fule in the tank for removal.
0) remove seat
1) drain fuel
2) undo cross over line (bottom front of gas tank.
3) shut off pet **** and remove fuel line from pet ****.
4)there should only be 2 bolts holding the tank on, one at the top front of the tank and one at the back of the tank.
All in all a pretty easy (but possibloy messy) job.
Posted on Jun 06, 2009
Turn the Bike on and the Radio off and then follow the buttons on the screen. Most people think you have to do it while it is running and this does not work
Posted on Jun 28, 2009
The only idea that i can come up with is that you dont have a good ground..or the guage was bad when you bought it..i hope this..Keith
Posted on Jul 02, 2009
The fork oil is a very specific job needing a manual and a special tool, I don't want to insult anyones mechanical knowledge but if you have never done it before, best to take somewhere else. Engine oil on the other hand is easy, the drain tube to any softail is on the right side by where the frame meets the swing arm, has somekind of plug in it. Start and run bike for a little while, long enough to get it warm but not hot. Remove fill plug and then remove plug in drain line. Using a peice of cardboard or something put in between filter and frame , directing the oil to your drain pan instead of where ever it goes. Put 1 qt oil back in (after everything is reinstalled) start the bike and make sure the oil light goes out, when it does shut bike off and fill to the point that when it is standing upright you get a little oil on the tip of your finger, over filling may result in loss of oil cap from pressure (been there)
Posted on Feb 16, 2010
It's a lot of work.
First, disconnect and remove the battery. Don't want to lose a finger.
Drain the primary and remove the outer primary cover.
Remove the small bolt that holds the jackshaft onto the starter and remove it if you can. If it won't come out, you'll have to take the nut off the clutch assembly and slide it out just far enough to get the jackshaft out. To get to the nut, remove the clutch rod adjuster in the center of the clutch assembly by removing the snap ring. Loosen the nut, left handed threads. When retorquing 60-80 foot pounds, left handed. There is a coupling that connects the jackshaft to the starter, mark which way it comes out. Tapered end towards starter.
Remove the exhaust system if needed.
Remove all bolts holding the oil tank and lift it up as high as possible.
Disconnect the large battery cable and the small wire at the top of the starter.
Remove the two large bolts that hold the starter onto the inner primary cover.
Work starter out.
Posted on Apr 01, 2010
Tips for a great answer:
Jan 28, 2014 | 2000 Harley Davidson FLHTCUI Electra Glide...
Jan 20, 2014 | 2003 Harley Davidson FLHRCI Road King...
Aug 22, 2013 | 2000 Harley Davidson FLHTCUI Electra Glide...
Jul 14, 2013 | 2008 Harley Davidson FLHTCU Ultra Classic...
Feb 10, 2013 | 2003 Harley Davidson FLHTCUI Electra Glide...
Dec 15, 2012 | 2003 Harley Davidson FLHRCI Road King...
Nov 05, 2012 | 2004 Harley Davidson FLHTCUI Electra Glide...
May 29, 2011 | 2003 Harley Davidson FLSTC Heritage...
51 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: