Question about 2006 Harley Davidson FXDBI Street Bob

1 Answer

Reset alarm system 2006 street bob - 2006 Harley Davidson FXDBI Street Bob

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Harley Davidson Master
  • 40,627 Answers

Hi Anonymous, for more information on your question please visit the websites below and good luck:
Set Change Override Transport Harley Security Alarm PIN Code No Key Fob...

Posted on May 30, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

goofduck
  • 490 Answers

SOURCE: my 2006 dyna street bob efi back fires

that is usually caused by a too rich main jet
dumping too much fuel and it is igniting it in the pipe

Posted on Apr 16, 2009

  • 10 Answers

SOURCE: Running Fuel for 2006 Street Bob FXDBI

These bikes were designed to operate on REG. fuel. If you need a cleaner or feul additive to help use P.I. from Amsoil. If you are interested in saving money and fuel and on this product contact me and I'll show you how. steveb@ejourney.com

Posted on Jul 07, 2009

jigsaw_9077
  • 308 Answers

SOURCE: Speedometer stopped working and mileage is not

check the wires connected to the speedometer .if the speedometer is not working replace speedometer.

Posted on Jul 10, 2009

  • 269 Answers

SOURCE: I have error codes on 2006 HD street bob. Bike will not start.

The codes are the following depending on your bike (EFI or Carb).:

P0373 CKP Sensor Intermittent Carb
P0373 CKP Sensor Intermittent EFI
P0374 CKP Sensor Not Detected Carb
P0374 CKP Sensor Synch Error EFI
U1255 Missing Message at Speedometer EFI
U1255 Serial Data Error/Missing Message EFI
U1255 Serial Data Error/Missing Message Instruments
U1255 Serial Data Error/Missing Message TSM/TSSM
this could be a number of potential things or maybe just a loose connection or ground somewhere. you are probably best to go to a shop, sorry.

Posted on Aug 14, 2009

wd4ity
  • 4565 Answers

SOURCE: Changing grips. Any suggestions or warnings,

Usually when you change the grips on the throttle side, depending on what type of replacement grips you bought, you'll be replacing the throttle sleeve as well. This means that you will be messing with the throttle and idle cables.

Loosen both cables at the adjusters as loose as they will go. Then, remove the two bolts that hold the right hand switch housing together. Carefully seperate the two halves. Do not damage the wires going to the switch. Work the throttle cable and the idle cable out of there slots in the throttle sleeve of the old grip. Be careful not to loose the brass ferrel that goes over the cable end. Lubricate the inside of the new throttle sleeve, the handlebar, and the area where the cables hook up with white lithium grease. Reassemble cables into new sleeve and reassemble the switch housing.

Once you have everything back together, adjust the throttle cable first and leave just a bit of slack in the cable. You should be able to freely "rock the throttle grip" before you feel the cable tighten up, Just a bit. Then adjust the idle cable about the same way.

Now, Turn the throttle cable to Wide Open throttle position and release it. It should "snap" shut, do this again from half and quarter throttle to make sure it works as it should. Failure to insure that the throttle operates properly can cause serious injury or death.

If you are simply replacing a grip on each side of the handlebar, use a long slender blade screwdriver or an ice pick to slide between the handlebar and the grip. Spray some WD40 in the work the grip a bit and it will break loose. Clean the throttle sleeve and handlebar off alcohol. Now, some people like to use "Grip Glue" on the new grips. Put the glue inside the grip and slide it up on the handlebar. If you put the glue on the handlebar, it will roll up in front of the grip as you slide it on to the handlebar or throttle sleeve. Make sure you "align" the two grips so they look the same before the glue sets.

Good Luck
Steve

Posted on Jul 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No indicators no dash how to reset alarm


Hi Steve, for more information about your question please visit the website below. Good luck and have nice day.
Set Change Override Transport Harley Security Alarm PIN Code No Key Fob...

Jun 13, 2015 | 2007 Harley Davidson FXDB Dyna Street Bob

1 Answer

How do you reset the security alarm on a Harley Davidson dyna street bob


Maybe the dealer will tell you. I don't have any resources for that. My old 2000 manual doesn't even address that.

Just call the service dept and ask for help. They should be willing to give you that little bit of info over the phone.

But have pen and paper handy. There might be several steps to it.

Jul 03, 2012 | 2008 Harley Davidson FXDB Dyna Street Bob

1 Answer

Pics on drain plug on 2006 harley davidson dtreet bob


Hi Anonymous, for more information on your question please visit the websites below and good luck:
DIY Oil Change on 2003 Harley Davidson Dyna

Mar 20, 2012 | 2006 Harley Davidson FXDBI Street Bob

1 Answer

2006 Harley Street Bob will not start


Sounds like the battery is bad - no amperage --- If you had the battery load tested & you know it's good, reset the TSSM. The procedure will be in the owners manual.

Nov 26, 2011 | 2006 Harley Davidson FXDBI Street Bob

1 Answer

Bike won't start


change the battery in the round black alarm thing a ma jig

Apr 28, 2010 | 2006 Harley Davidson FXDBI Street Bob

1 Answer

Running Fuel for 2006 Street Bob FXDBI


These bikes were designed to operate on REG. fuel. If you need a cleaner or feul additive to help use P.I. from Amsoil. If you are interested in saving money and fuel and on this product contact me and I'll show you how. steveb@ejourney.com

Jul 07, 2009 | 2006 Harley Davidson FXDBI Street Bob

Not finding what you are looking for?
2006 Harley Davidson FXDBI Street Bob Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...