Question about Motorcycles

Open Question

Baja 196cc bike will not start my Carb keeps filling up with gas got level in Carb to close but still wont start. Dont know if its the cold wheather but how can I get it to start

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 10 Answers

SOURCE: 49cc Baja not getting gas/ wont start

have you checked the fuel pump? You can take the hose of the carb fuel rail and with the ignition on the fuel pump should spit fuel out. If it does... move on to the fuel filter it could be clogged. Good luck

Posted on Jun 14, 2009

  • 40 Answers

SOURCE: baja 90cc 4wheeler wont start

I would check the timing to make sure that it is correct because if it's not firing at the correct time it will not start.

Posted on Aug 15, 2009

DoubleClutch
  • 376 Answers

SOURCE: easy way to start a cold dr350 dualsport or

I would check the spark plugs. Take a spare spark plug that is known to be good and unplug the wire from the plug that is in the head and put the spare plug in and put it against the head to make a ground and try starting it to see if you have any spark. If you are not then test at the coil with a voltage meter set on 12 volt and try again to see if you have voltage to the coil. If there is no voltage to the coil then you will need to test the stater.

Posted on Oct 31, 2009

  • 474 Answers

SOURCE: Kawasaki ZZR 250. Engine hydrauliced after fuel

sounds like you blew a set of piston rings. instead of building compression in the cylinder its pressurizing your crank case forceing the oil out the breather into your air box

Posted on Dec 19, 2009

  • 209 Answers

SOURCE: i have a yamaha yz 250 98' and wont start i

coil

Posted on Apr 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Baja warrior 196cc mini bike engine torque specs ???


Hi, Randall for more information about your question and valuable "FREE" downloads that you will need please visit the websites below. Good luck and have a nice day.
Baja MB 200 Operator Manual
Baja Mini Bike Parts Baja Heat Parts Baja Mini Baja Parts
Mini Bike Easy Governor Bypass 1080P
http://docsfiles.com/pdf_baja_bike_manual.html

Mar 22, 2016 | Motorcycles

1 Answer

My Baja 196cc takes off when I start it don't know why just that the bike was given to me recently, no manual


Hi, Jeff your mini bike has a centrifugal clutch and the previous owner may have tried to modify/bypass the governor for more speed if not done properly it will give you the undesired result which can be easily fixed by watching the video below I am sorry you can't find the first and best tool you ever bought for your Baja but despair not for a mere $0 you can download another one. For more information about your issue, please visit the websites below. Good luck and have a nice day.Mini Bike Easy Governor Bypass 1080P

http://www.bajamotorsports.com/system/documents/86_OWNERS_MANUAL_-_WR65_Warrior_Mini_Bike_US_VIN_prefix_LUAH_.pdf
Mini Baja 6 5hp motor or other problems on 4Strokes com Forums

Jan 01, 2016 | Motorcycles

1 Answer

Baja 96cc mini bike wont start. Ran last year. Cleaned carb, replace plyg, fresh gas.... Wont start..? Help...


Remove the float bowl from the carburetor and check to make sure the float needle valve is not stuck in the closed position or clogged. If it's stuck or clogged, the bowl won't fill and fuel will never make it to the combustion chamber.... IT WON'T RUN!!! LOL!!! Good luck! Hope I was able to help. Bill

Aug 01, 2014 | Motorcycles

1 Answer

Ran my baja sc125 til it ran outta gas, filled it, now it wont start


Hi, Carlos if you have an old bike that has not had regular fuel system maintenance and you run the fuel tank dry I feel your pain. All the contaminants water-dirt-rust-liner paint flakes-ethanol sludge etc. that lived in the bottom of your fuel tank get mixed with the last few oz. of fuel left in the tank and enter the fuel system clogging up fuel filters-fuel valves-fuel lines-carburetor jets-needle jets and seats-fuel injectors etc. You fill up your fuel tank and guess what your bike does not start or if it does it runs like dog caca, a complete cleaning of the fuel system is mandatory, the procedure is as follows:
1. Drain the fuel tank and inspect the inside for leftover uninvited guests decontaminate as necessary for rusty environments install a liquid fuel liner.
2. In tank fuel pumps with external filters need to be cleaned.
3. Fuel valves need to be rebuilt with a new gasket kit.
4. Fuel lines need to be inspected for integrity and replaced as necessary any inline fuel filter should be cleaned or replaced.
5. Carburetors need to be disassembled then "DIPPED" and soaked in a commercial carb cleaning solution Gunk sells 1/2 gallon pails with meshed screen baskets. Reassemble using new rebuild kits. Record all jet sizes and float level for fine tuning.
6. Fuel injectors and fuel rails need to be properly cleaned and tested for optimum performance, if necessary send off any suspect injectors to "InjectorRx.com" for a modest fee they will refurbish the unit back to factory specs.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
2008 Baja sc 150 wont start
GY6 Scooter Fuel and Vacuum system hands on
http://www.49ccscoot.com/manuals/Baja_SC150_Owners_Manual.pdf
Baja Sun City 125 SC125 125cc Scooter Parts
http://www.family-motorsports.net/GY6-50cc-150cc.pdf

May 25, 2017 | TN'G Baja 150 Motorcycles

1 Answer

I havent started my baja mini bike since last fall and now it wont start it seems to be not getting any gas


Chances are the carb is plugged up with stale gas. The carb will need to be disassembled and thoroughly cleaned, including all passages.

May 20, 2010 | Mini Motorized Bike

3 Answers

196 cc baja mini bike dies if I try and give throttle


Well i had the same Baja mini bike and to be honest with you, you will run into alot more problems with that bike bec they build them so cheap, I and alot of others had 1 thing go after the other on that modle and to me they just aint worth the trouble or money, But check the coil and make sure to

Jul 21, 2009 | Mini Motorized Bike

1 Answer

Have baja 125 motorsport idels fine but when throddle up it dies


ALWAYS have a fire extinguisher at hand when working on carburetors.
Remove the water trap bowl at the bottom of the petcock, (gas valve). Is there any water or trash in the bowl? Drain a cup of gas from the tank. Is there any water or trash in the cup? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ).

Drain the carburetor. There may be a screw on the lower side of the carb float bowl. Remove the screw then replace it after the fuel drains. Turn the gas back on and wait a minute for the carb to fill with gas. Install a new stock NGK spark plug and try to start the engine. If the bike doesn't start and run properly then shut off the gas and remove the carburetor from the engine.

Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the idle screw and the air screw on the outside throat of the
carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two adjusters down. Only screw these in until they LIGHTLY seat. Now turn each adjuster one and one half turns outward. Put the rest of the
carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine. This process should get you back on the road.

Please rate this solution. Thanks!

Apr 30, 2009 | 2007 TN'G Baja 150

2 Answers

89 jeep yj wont keep running


sounds like you need to rebuild your carb. I just had mine done for my jeep the hardest part was finding someone to do it. ps mine only cost 50 bucks so dont get ripped off. good luck and hope this helps.

Apr 19, 2009 | 1990 Jeep Wagoneer Limited

1 Answer

The bike keeps bogging


Remove the water trap bowl at the bottom of the petcock, (gas valve). Any water or trash in the bowl? Drain a cup of gas from the tank. Any water or trash in the cup? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ).

Drain the carburetor. There should be a screw on the lower side of the carb float bowl. Remove the screw then replace it after the fuel drains. Turn the gas back on and wait a minute for the carb to fill with gas. Install a new stock NGK spark plug and try to start the engine. If the bike doesn't start and run properly then shut off the gas and remove the carburetor from the engine.

Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the two screws on the outside throat of the carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two screws down. Only screw these in until they LIGHTLY seat. Now turn each screw one and one half turns outward. Put the rest of the carb back together, clean the air filter and install the carb. Be sure the bolts are tight. Let the float bowl fill then start the engine. Set the idle speed with the idle screw. This process should get you back on the road.


Please rate this solution. Thanks love_havin-s!!

Apr 04, 2009 | 2003 Suzuki RM 125

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...